Ford 2009 Explorer Sport Trac v.2 User Manual

Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 18Entertainment Systems 21How to get going 21AM/FM stereo with CD 25AM/FM stereo

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

• Compass display• Compass zone adjustment• Compass calibration adjustment• Oil Life Setup and Start ValueAWD lockSelect this function from the SETUP

6. BRAKE FLUID LEVEL7. PARK BRAKE8. FUEL LEVEL AND DISTANCE TO EMPTYUnits (English/Metric)1. Select this function from theSETUP MENU for the current u

1. To change the delay time of theautolamp feature, select thisfunction from the SETUP MENU.2. Press the RESET control to selectthe new Autolamp delay

Reverse Sensing System (Park Aid) (if equipped)This feature sounds a warning tone to warn the driver of obstacles nearthe rear bumper, and functions o

Note: Compass zone and calibration adjustments can be entered byusing the INFO and SETUP MENU controls or using the reset button ontop of the compass

Compass calibration adjustment (if equipped)Perform compass calibration in an open area free from steel structuresand high voltage lines. For optimum

2. Press and hold the RESETcontrol for more than two seconds.Oil life is set to 100% and “OILCHANGE SET TO 100%” isdisplayed.Note: To change oil life

Warning display StatusDoor ajar Warning cannot be resetFuel level low Warning returns after10 minutesPark brake engagedCheck brake systemCheck park ai

PARK BRAKE ENGAGED — Displayed when the manual park brake isset, the engine is running and the vehicle is driven more than 3 mph(5 km/h). If the warni

TRAILER SWAY REDUCE SPEED — Displayed when your trailerstarts to sway when towing. Refer to Trailer Sway Control in theDriving chapter for more inform

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

TAILGATE LOCKThe tailgate lock is designed to helpprevent theft of the tailgate.• Insert ignition key and turn to theright to lock.• Turn ignition key

Exterior tiedown hooksExterior tiedown hooks mounted onthe side of the pickup box:• can be used to secure loadswithin the pickup box.• can be used to

Activating Cargo Cage TheftDeterrent Device:The following procedure can bedone with the cargo cage in thestowed or extended position.1. Locate the Phi

To open the front panel:• Open the driver side lock coverand unlock the front panel usingyour ignition key.• Lift the panel to access items inthe pick

To remove the tonneau cover:The tonneau cover weighs 70 lb.(29 kg) and needs to be supportedduring removal since the panels willautomatically lock whe

WARNING: Do not leave children, unreliable adults, or animalsunattended in the vehicle. On hot days, the temperature in thepickup box can rise very qu

Pickup box storage compartmentThe storage compartments are located inside the pickup box behind thewheel wells.The storage compartments havebeen desig

To adjust cross-bar position (ifequipped):1. Loosen the thumbwheel at bothends of the cross-bar (If thethumbwheel is too tight to releaseby hand, a sm

KEYSOne key operates the door, tailgate, and tonneau cover locks and startsthe vehicle. Always carry a spare key with you in case of an emergency.Your

Deactivating/activating autolockYour vehicle comes with the autolock feature enabled. There are fourmethods to enable/disable this feature:• Through y

WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may

Keyless entry keypad procedure1. Turn the ignition to the off position.2. Close all doors.3. Enter 5–digit entry code4. Press and hold the 3 • 4. Whil

Power door unlock/lock procedureYou must complete Steps 1-5 within 30 seconds or the procedure willhave to be repeated. If the procedure needs to be r

Power door lock/unlock inhibit feature (if equipped)If the key is not in the ignition, all doors are closed, and the vehicle hasbeen locked using the

CHILDPROOF DOOR LOCKS• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the outside when the

Your vehicle is equipped with a remote entry system which allows you to:• unlock the vehicle doors withouta key.• lock all the vehicle doors withouta

Locking the doors1. Press and release to lock all the doors. The lamps will flash.Note: If any door is not closed properly, the lamps will not flash u

2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board.3. Remove the old battery.Note: Please refer to localreg

3. Turn the key from the 1 (off)position to 3 (on).4. Cycle eight times rapidly (within10 seconds) between the 1 (off)position and 3 (on). Note: Theei

SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED)You can use the keyless entrykeypad to:• lock or unlock the doors withoutusing a key.• activate or deact

Erasing personal code1. Enter the factory set 5–digit code.2. Within five seconds, press the 1 • 2 on the keypad and release.3. Press and hold the 1 •

Service engine soon: The serviceengine soon indicator lightilluminates when the ignition is firstturned to the on position to checkthe bulb and to ind

Note: The SecuriLock™ passive anti-theft system is not compatible withnon-Ford aftermarket remote start systems. Use of these systems mayresult in veh

Automatic disarmingSwitching the ignition to the on position with a coded key disarms thevehicle.• The theft indicator will illuminate for three secon

Please read and understand the entire procedure before you begin.1. Insert the first previously programmed coded key into the ignition.2. Turn the ign

SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event o

To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o

To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous

WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Adjusting the front manual seat (if eq

Using the manual lumbar support (if equipped)For more lumbar support, turn thelumbar support control toward thefront of vehicle.For less lumbar suppor

WARNING: To reduce the risk of possible serious injury: Do nothang objects off seat back or stow objects in the seatback mappocket (if equipped) when

Press the control to move the seatforward, backward, up or down.Press the control to recline theseatback forward or rearward.Using the power lumbar su

• Optional instrument clusterBrake system warning light: Toconfirm the brake system warninglight is functional, it willmomentarily illuminate when the

Heated seats (if equipped)WARNING: Persons who are unable to feel pain to the skinbecause of advanced age, chronic illness, diabetes, spinal cordinjur

REAR SEATSIf needed, when installing some high back child restraints, the headrestraints of the second row seating positions can be removed. Insert at

Folding down the 2nd row 60/40 seatsEnsure that the head restraint is in the down position and no objectssuch as books, purses or briefcases are on th

Note: For 60% seats, ensure thatthe seatback is fully latched to therear of the cab.2. Lift up on the head restraint untilit locks into its original p

Your vehicle’s Personal Safety System威 consists of:• Driver and passenger dual-stage airbag supplemental restraints.• Front safety belts with pretensi

information early in the crash event on the severity of the impact. Thisallows your Personal Safety System威 to distinguish between differentlevels of

Front safety belt usage sensorsThe front safety belt usage sensors detect whether or not the driver andfront outboard passenger safety belts are faste

Safety restraints precautionsWARNING: Always drive and ride with your seatback uprightand the lap belt snug and low across the hips.WARNING: To reduce

WARNING: Safety belts and seats can become hot in a vehiclethat has been closed up in sunny weather; they could burn asmall child. Check seat covers a

• Front and rear seats2. To unfasten, push the release button and remove the tongue from thebuckle.• Front and rear seatsAll safety restraints in the

Safety belt: Reminds you to fastenyour safety belt. A Belt-Minder威chime will also sound to remind youto fasten your safety belt. Refer tothe Seating a

Automatic locking modeWhen to use the automatic locking modeIn this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to

How to disengage the automatic locking modeUnbuckle the combination lap and shoulder belt and allow it to retractcompletely to disengage the automatic

Front safety belt height adjustmentYour vehicle has safety belt heightadjustments at the front outboardseating positions. Adjust the heightof the shou

To adjust the comfort guide:1. Slip the shoulder belt into thebelt guide.2. Slide the guide up or down alongthe webbing so that the belt iscentered on

Safety belt warning light and indicator chimeThe safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occup

When the Belt-Minder威 feature is activated, the safety belt warning lightilluminates and the warning chime sounds for six seconds every30 seconds, rep

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra

WARNING: Do not sit on top of a buckled safety belt or insert alatchplate into the buckle to avoid the Belt-Minder威 chime. Todo so may adversely affec

WARNING: While the design allows you to deactivate yourBelt-Minder威, this system is designed to improve your chances ofbeing safely belted and survivi

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right

WARNING: Never remove the coolant reservoir cap while theengine is running or hot.Low tire pressure warning:Illuminates when your tire pressureis low.

WARNING: Never place your arm over the airbag module as adeploying airbag can result in serious arm fractures or otherinjuries.To properly position yo

Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt

• one or more impact and safing sensors.• a readiness light and tone.• diagnostic module.• and the electrical wiring which connects the components.• F

The front passenger sensing system will turn off the passenger seat sideairbag if:• the seat is empty and safety belt is unbuckled.The front passenger

• If the indicator lamp remains lit even after this, the person should beadvised to ride in the rear seat.OccupantPass Airbag OffIndicator LampPasseng

ObjectsPass Airbag OffIndicator LampPassenger AirbagSmall (i.e. three-ring binder,small purse, bottled water)Unlit DisabledMedium (i.e. heavy briefcas

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit.If the airbag readi

A difficulty with the system is indicated by one or more of the following:• The readiness light will eitherflash or stay lit.• The readiness light wil

How does the side airbag system work?The design and development of the side airbag system includedrecommended testing procedures that were developed b

AdvanceTrac威: Flashes when theAdvanceTrac威 with RSC威 system isactive. Illuminates solid when thesystem has been disabled (by thedriver or as a result

WARNING: Several air bag system components get hot afterinflation. Do not touch them after inflation.WARNING: If the sideairbag has deployed, theairba

WARNING: All occupants of the vehicle including the drivershould always wear their safety belts even when an airbag SRSand Safety Canopy威 system is pr

The Safety Canopy威 system, in combination with safety belts, can helpreduce the risk of severe injuries in the event of a significant side impactcolli

WARNING: If the Safety Canopy威 system has deployed, theSafety Canopy威 will not function again. The SafetyCanopy威 system (including the A, B and C pill

Disposal of airbags and airbag equipped vehicles(including pretensioners)Contact your authorized dealer as soon as possible. Airbags MUST BEdisposed o

Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfantsortoddlersChildren weighing 40 lb

Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe

WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli

If the child is the proper height, age, and weight (as specified by yourchild safety seat or booster manufacturer), fits the restraint and can berestr

Installing child safety seats with combination lap and shoulder beltsIf needed, when installing some high back child restraints, the headrestraints of

Turn signal: Illuminates when theleft or right turn signal or thehazard lights are turned on. If theindicators stay on or flash faster, check for a bu

• Keep the buckle release button pointing up and away from the safetyseat, with the tongue between the child seat and the release button,to help preve

3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi

8. Remove remaining slack from thebelt. Force the seat down with extraweight, e.g., by pressing down orkneeling on the child restraint whilepulling up

however the safety belt can still be used to attach the child seat. Forforward-facing child seats, the top tether strap must also be attached tothe pr

WARNING: Never attach two child safety seats to the sameanchor. In a crash, one anchor may not be strong enough to holdtwo child safety seat attachmen

If the safety seat is not anchored properly, the risk of a child beinginjured in a crash greatly increases.Attaching child safety seats with tether st

2. Locate the correct anchor for theselected rear seating position.• You may need to pull the seatback forward to access the tetheranchors. Make sure

4. Clip the tether strap to theanchor and return the seat back toits locked position.If the tether strap is clippedincorrectly, the child safety seat

Booster seats position a child so that vehicle lap/shoulder safety belts fitbetter. They lift the child up so that the lap belt rests low across the h

Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction

Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature,

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a

The importance of shoulder beltsUsing a booster without a shoulder belt increases the risk of a child’shead hitting a hard surface in a collision. For

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary

• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and

government test course. For example, a tire graded 150 would wear oneand one-half (11⁄2) times as well on the government course as a tiregraded 100. T

• Tire Identification Number (TIN): A number on the sidewall ofeach tire providing information about the tire brand andmanufacturing plant, tire size

You are strongly urged to buy a reliable tire pressure gauge, as automaticservice station gauges may be inaccurate. Ford recommends the use of adigita

If you are checking tire pressure when the tire is hot, (i.e. driven morethan 1 mile [1.6 km]), never “bleed” or reduce air pressure. The tires arehot

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them

Locks and Security 118Keys 118Locks 118Anti-theft system 129Seating and Safety Restraints 133Seating 133Safety restraints 143Airbags 159Child restrain

Trip odometer: Registers the miles (kilometers) of individual journeys.• Standard instrument clusterPress the SELECT/RESET controlonce to switch from

U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s

WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w

WARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the tires; spinning the tires can tear the tire andcause an explosion.

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can b

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/

11. Maximum Load: Indicates the maximum load in kilograms andpounds that can be carried by the tire. Refer to the Safety ComplianceCertification Label

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

AUDIO SYSTEMSQuick start — How to get goingWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly

following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including inter

When your temporary spare tire is installedWhen one of your road tires needs to be replaced with the temporaryspare, the TPMS system will continue to

Low TirePressureWarning LightPossiblecauseCustomer Action RequiredFlashing WarningLightSpare tire inuseYour temporary spare tire is in use.Repair the

SNOW TIRES AND CHAINSWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. The use ofnon-recommende

your vehicle, familiarize yourself with the following terms for determiningyour vehicle’s weight ratings, with or without a trailer, from the vehicle’

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or performance, e

WARNING: Do not use replacement tires with lower loadcarrying capacities than the original tires because they maylower the vehicle’s GVWR and GAWR lim

• A final example for your vehicle with 1,400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the

Listening to satellite radio (if equipped)1. If the audio system is turned off,press VOL-PUSH to turn the radioon. Turn VOL-PUSH to adjust thevolume.N

2. Weigh your vehicle without cargo. To obtain correct weights, take yourvehicle to a shipping company or an inspection station for trucks.3. Subtract

4x2GCWR (Gross Combined Weight Rating)/Trailer WeightEngine Rear axle ratio MaximumGCWR-lb. (kg)Trailer weightrange-lb. (kg)(0-Maximum)4.0L SOHC Class

4WD and AWDGCWR (Gross Combined Weight Rating)/Trailer WeightEngine Rear axle ratio MaximumGCWR-lb. (kg)Trailer weightrange-lb. (kg)(0-Maximum)4.6L* C

Class III Trailer Hitch Safety ChainLoops can be used as recoveryhooks.Do not attach safety chains to the bumper.Trailer brakesElectric brakes and man

Driving while you towWhen towing a trailer:• To ensure proper “break-in” of powertrain components, do not trailertow during the first 1,000 miles (1,6

• If you will be towing a trailer frequently in hot weather, hillyconditions, at GCWR, or any combination of these factors, considerrefilling your rea

RECREATIONAL TOWINGFollow these guidelines if you have a need for recreational (RV) towing.An example of recreational towing would be towing your vehi

STARTINGPositions of the ignition1. Off — shuts off the engine and allaccessories/locks the steering wheel,gearshift lever and allows keyremoval.2. Ac

WARNING: If you smell exhaust fumes inside your vehicle, haveyour dealer inspect your vehicle immediately. Do not drive if yousmell exhaust fumes.Impo

• Make sure the gearshift is in P(Park).3. Turn the key to 3 (on) withoutturning the key to 4 (start).Some warning lights will briefly illuminate. See

2. Press CD to enter CD mode. If adisc is already loaded into thesystem, CD play will begin where itended last.For a single CD system, if a discis not

Starting the engine1. Turn the key to 3 (on) withoutturning the key to 4 (start). If thereis difficulty in turning the key,rotate the steering wheel u

ENGINE BLOCK HEATER (IF EQUIPPED)An engine block heater warms the engine coolant which aids in startingand allows the heater/defroster system to respo

• Be sure that areas where the vehicle is parked are clean and clear ofall combustibles such as petroleum products, dust, rags, paper andsimilar items

brake pedal pulsation may be observed during ABS braking and thebrake pedal may suddenly travel a little farther as soon as ABS braking isdone and nor

The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned on) until theparking brake is released.

ADVANCETRAC姞 WITH ROLL STABILITY CONTROL™ (RSC姞)STABILITY ENHANCEMENT SYSTEMWARNING: Vehicle modifications involving braking system,aftermarket roof r

The AdvanceTrac威 with RSC威 system provides the following stabilityenhancement features for certain driving situations:• Traction Control (TCS), which

• If the driving condition is severe and your foot is not on the brake, thebrake pedal may move as the systems applies higher brake forces. Youmay als

Certain adverse driving maneuvers may activate the Electronic StabilityControl system, which include but are not limited to:• Taking a turn too fast•

with RSC威 system can be restored by pressing the AdvanceTrac威 withRSC威⬙Off⬙ button again or by turning off and restarting the engine.If you switch off

While in folder mode, pressFOLDER to access the previousfolder on MP3 discs, if available.While in folder mode, pressFOLDERto access the nextfolder on

During Trailer Sway Control events, the icon in the instrumentcluster will flash momentarily. The message center will also display:TRAILER SWAY REDUCE

• loose or worn steering components• improper steering alignmentA high crown in the road or high crosswinds may also make the steeringseem to wander/p

AUTOMATIC TRANSMISSION OPERATIONBrake-shift interlockThis vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever fr

Driving with a 5–speed automatic transmission (if equipped)This vehicle is equipped with an Adaptive Transmission Control Strategy.This Adaptive Trans

P (Park)This position locks the transmissionand prevents the rear wheels fromturning.To put your vehicle in gear:• Start the engine• Depress the brake

D (Drive) without OverdriveOverdrive can be deactivated bypressing the transmission controlswitch on the side of the gearshiftlever.• This position al

Forced downshifts• Allowed in D (Overdrive) or Drive.• Depress the accelerator to the floor.• Allows transmission to select an appropriate gear.Drivin

P (Park)This position locks the transmissionand prevents the rear wheels fromturning.To put your vehicle in gear:• Depress the brake pedal• Start the

D (Drive) without OverdriveOverdrive can be deactivated bypressing the transmission controlswitch on the side of the shift lever.• This position allow

1 (First)• Transmission operates in 1st gear only.• Provides maximum engine braking.• Allows upshifts by moving gearshift lever.• Will not downshift i

AM/FM Single CD/MP3 satellite compatible sound system(if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and

WARNING: This system is not designed to prevent contact withsmall or moving objects. The system is designed to provide awarning to assist the driver i

The RSS automatically turns on when the gear selector is placed in R(Reverse) and the ignition is on. A control in the message center allowsthe driver

Using the Control Trac 4WD system4X4 AUTO - Provides electronically-controlled four-wheel drive withpower delivered to all four wheels as required for

WARNING: If your vehicle is equipped with AWD, a spare tire ofa different size than the road tires should never be used. Such atire could make the veh

Driving off-road with truck and utility vehiclesAWD and 4WD vehicles are specially equipped for driving on sand, snow,mud and rough terrain and have o

• It often may be less risky to strike small objects, such as highwayreflectors, with minor damage to your vehicle rather than attempt asudden return

Emergency maneuvers• In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle, i.e.,

ParkingOn some 4WD vehicles, when the transfer case is in the N (Neutral)position, the engine and transmission are disconnected from the rest ofthe dr

Mud and waterIf you must drive through highwater, drive slowly. Traction orbrake capability may be limited.When driving through water,determine the de

Driving on hilly or sloping terrainAlthough natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should

In CATEGORY MODE, press / to scroll through the list ofavailable SIRIUS channel Categories (Pop, Rock, News, etc.). Refer toCategory Mode under Menu f

Driving on snow and iceAWD and 4WD vehicles have advantages over 2WD vehicles in snow andice but can skid like any other vehicle.Should you start to s

Failure to maintain your vehicle properly may void the warranty, increaseyour repair cost, reduce vehicle performance and operational capabilitiesand

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsIn Canada, for uninterrupted Roadside Assistance co

FUEL PUMP SHUT-OFF SWITCHFUELRESETThe fuel pump shut-off switch is a device intended to stop the electricfuel pump when your vehicle has been involved

FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth

Passenger compartment fuse panelThe fuse panel is located below theinstrument panel on the driver’sside.To remove a fuse use the fuse puller tool prov

Fuse/RelayLocationFuse AmpRatingProtected Circuits6 20A Door unlock/lock7 15A Trailer tow stop/turn lamps8 15A Ignition switch power, PATS, Cluster9 2

Fuse/RelayLocationFuse AmpRatingProtected Circuits27 15A Not used28 10A Manual/DEATC climate controlCB1 25A WindowsThe following relays are located on

The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingProtected Circuits1 50A** BATT 2 (SJB)2 50A** BATT 3 (SJB)3 50A** BATT 1 (

• DELETE SONG: Press OK to delete a song from the system’smemory. Press/ to cycle through the saved songs. When thesong appears in the display that yo

Fuse/RelayLocationFuse AmpRatingProtected Circuits16 40A** Blower motor17 30A** Trailer tow electronic brakes18 — Not used19 — Not used20 30A** Front

Fuse/RelayLocationFuse AmpRatingProtected Circuits42 15A* Speed control deactivation switch,EVMV, MAFS, HEGO, EVR, CMS,(VCT1, VCT2, CMCV on 4.6L only)

Have a flat serviced by an authorized dealer in order to prevent damageto the TPMS sensor, refer to Changing tires with TPMS in the Tires,Wheels and L

• Use more than one dissimilar spare tire at a time• Use commercial car washing equipment• Try to repair the dissimilar spare tireUse of one of the di

Stopping and securing the vehicle1. Park on a level surface, activatethe hazard flashers and set theparking brake.2. Place gearshift lever in P (Park)

4. Remove the chock and jack toolsfrom the provided bag and rotatethe wrench socket out from thehandle.Removing the spare tire1. Assemble the jack han

4. With the spare tire on the ground,remove the retainer from the sparetire.Changing the spare tireWARNING: When one of the rear wheels is off the gro

1. Block the wheel that is diagonallyopposite of the flat tire using thewheel chock provided with yourvehicle.2. Use the tip of the lug wrench toremov

5. Position the jack according to theillustrated guides and turn the jackhandle clockwise until the tire is amaximum of 1 inch (25 mm) off theground.W

9. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torquespecifications later in this chapterfor the proper lu

To activate, press MENU repeatedly until RBDS (ON/OFF) appears inthe display. Use/ / SEEK to toggle RBDS ON/OFF. WhenRBDS is OFF, you will not be able

2. Stow the wheel ornament (if removed) in a safe location in the vehicle(such as the glove box or jack stowage compartment) so it will notbecome dama

JUMP STARTINGWARNING: The gases around the battery can explode ifexposed to flames, sparks, or lit cigarettes. An explosion couldresult in injury or v

Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to the g

WARNING: Do not connect the end of the second cable to thenegative (-) terminal of the battery to be jumped. A spark maycause an explosion of the gase

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheelson the ground (without dollies) and the rear wheels off the ground.On 4x4/AW

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized

In Canada:Mailing Address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph

TRACK/FOLDER MODE: Available only on MP3 discs in CD mode.In track mode, pressSEEK, SEEK to scroll through all tracks onthe discIn folder mode, pressS

In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext

procedure outlined on the first page of the Customer Assistance section,you may be eligible to participate in the BBB AUTO LINE program.The BBB AUTO L

The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have

If you cannot find unleaded fuel or can only get fuel with an anti-knockindex lower than is recommended for your vehicle, contact a regionaloffice or

Obtaining a French owner’s guideFrench Owner’s Guides can be obtained from your authorized dealer orby writing to:Ford Motor Company of Canada, Limite

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is

• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent qu

ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when

4.6L V8 ENGINEPLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your authorized

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft Premium Windshield Washer Concentrate (ZC-32-A),available from your au

Customer Assistance 288Reporting safety defects (U.S. only) 294Reporting safety defects (Canada only) 294Cleaning 295Maintenance and Specifications 30

In satellite radio mode (if equipped), press SEEK, SEEK toseek to the previous/next channel. If a specific category is selected,(Jazz, Rock, News, etc

If a staining liquid like coffee/juice has been spilled on the instrumentpanel or on interior trim surfaces, clean as follows:1. Wipe up spilled liqui

LEATHER SEATS (IF EQUIPPED)Your leather seating surfaces have a clear, protective coating over theleather.• For routine cleaning, wipe the surface wit

Motorcraft Detail Wash (ZC-3-A)Motorcraft Dusting Cloth (ZC-24)Motorcraft Engine Shampoo and Degreaser (U.S. only) (ZC-20)Motorcraft Engine Shampoo (C

SERVICE RECOMMENDATIONS• Use the scheduled maintenance information to track routineservice.• Use only recommended fuels, lubricants, fluids and servic

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.0L SOHC V6 engine1. Engine oil filler cap2. Engine oil dipstick (out of view)3. Brake fluid reservoi

4.6L V8 engine1. Air filter assembly2. Engine oil filler cap3. Engine oil dipstick4. Brake fluid reservoir5. Power distribution box6. Battery7. Power

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

CHANGING THE WIPER BLADES1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to releas

5. Locate and carefully remove the engine oil level dipstick.• 4.0L V6 engine• 4.6L V8 engine6. Wipe the dipstick clean. Insert the dipstick fully, th

9. FOLDER: In folder mode,pressFOLDER to access theprevious folder on MP3 discs, ifavailable.10. FF (Fast forward): Press FFto manually advance in a C

• 4.0L V6 engine• 4.6L V8 engine• Oil levels above the upper hole may cause engine damage. Some oilmust be removed from the engine by an authorized de

To avoid possible oil loss, DO NOT operate the vehicle with theengine oil level dipstick and/or the engine oil filler cap removed.Engine Oil Recommend

4.6L 3V V8 EngineLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils “Certified For Gasoline Engines” by the AmericanPetroleum

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If

WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

• 4.0L V6 engine• 4.6L V8 engine• The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant

Adding engine coolantWhen adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. When the engine is cool, add the mixtu

For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when

Your cooling system may have a leak. Operating an engine with a lowlevel of coolant can result in engine overheating and possible enginedamage.Recycle

In satellite radio mode (if equipped), press and hold to hear a briefsampling of the next channels. Press again to stop. In CATEGORYMODE, press SCAN t

• Decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine damag

• Engine Oil Overheat Mode: The (Engine coolant temperature)indicator will be on. The instrument cluster has no separate oiltemperature indicator.Alon

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsWARNING: Do not overfill the fuel tank. The pressure in anoverfilled tank may c

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek med

Use the following guidelines to avoid electrostatic charge build-up whenfilling an ungrounded fuel container:• Place approved fuel container on the gr

WARNING: The fuel system may be under pressure. Removefuel filler cap slowly. Otherwise, fuel may spray out and injureyou or others.WARNING: If you do

Do not be concerned if your engine sometimes knocks lightly. However, ifit knocks heavily under most driving conditions while you are using fuelwith t

• The Service engine soon indicator may come on. For moreinformation on the Service engine soonindicator, refer toWarning lights and chimes in the Ins

• Have the vehicle loading and distribution the same every time.Your results will be most accurate if your filling method is consistent.Calculating fu

• Revving the engine before turning it off may reduce fuel economy.• Using the air conditioner or defroster may reduce fuel economy.• You may want to

Audiophile AM/FM in-dash six CD/MP3 satellite compatible soundsystem (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontr

EPA fuel economy estimatesEvery new vehicle should have a window sticker containing EPA fueleconomy estimates. Contact your authorized dealer if the w

WARNING: Exhaust leaks may result in entry of harmful andpotentially lethal fumes into the passenger compartment.Do not make any unauthorized changes

detected by the OBD-II may not have symptoms that are apparent,continued driving with the Service engine soonindicator on canresult in increased emiss

1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge indicator will benear the center o

transmission is not working properly, (i.e., if the transmission slips orshifts slowly) or if you notice some sign of fluid leakage.Transmission fluid

AIR FILTERRefer to scheduled maintenance information for the appropriateintervals for changing the air filter element.When changing the air filter ele

5. Install a new air filter element. Be careful not to crimp the filterelement edges between the air filter housing and cover. This could causefilter

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord Part Nameor equivalentFord Part Number / FordSpecificationBrake fluidBetween MINand

Item CapacityFord Part Nameor equivalentFord Part Number / FordSpecificationCooling systemstop leak pellets—Motorcraft CoolingSystem Stop LeakPelletsV

Item CapacityFord Part Nameor equivalentFord Part Number / FordSpecificationAutomatictransmission(6R80) fluid11.2 quarts(10.6L)3MotorcraftMERCON威 LV A

In satellite radio mode (if equipped), press / to tune to thenext/previous channel.In CATEGORY MODE, press/ to scroll through the list ofavailable SIR

Item CapacityFord Part Nameor equivalentFord Part Number / FordSpecificationWindshield washerfluid4.2 quarts(4.0L)Motorcraft PremiumWindshield WasherC

ENGINE DATAEngine 4.0L SOHC V6engine4.6L 3V V8engineCubic inches 245 281Required fuel 87 octane 87 octaneFiring order 1-4-2-5-3-6 1-3-7-2-6-5-4-8Ignit

IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli

The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of

LifestyleAsh cup / smoker’s packageNeutral tow kitRoof rail cross barsTrailer hitch drawbars, wiring harnesses and accessoriesTripTunes™ Advanced port

AAccessory delay ...73AdvanceTrac ...235Air cleaner filter ...335–336Air conditioning ..

Child safety seats - boosterseats ...188Cleaning your vehicleengine compartment ...297instrument pa

Engine block heater ...231Engine oil ...308checking and adding ...308dipstick ...

Infant seats(see Safety seats) ...178Inspection/maintenance (I/M)testing ...332Instrument panel

• DELETE SONG: Press OK to delete a song from the system’smemory. Press/ to cycle through the saved songs. When thesong appears in the display that yo

Passenger OccupantClassification Sensor ...145Pedals (see Power adjustablefoot pedals) ...78Power adjustab

Specification chart,lubricants ...337Speed control ...78Starting yourvehicle ...

RBDS: Available only in FM mode. This feature allows you to searchRBDS-equipped stations for a certain category of music format:CLASSIC, COUNTRY, INFO

TRACK/FOLDER MODE: Available only on MP3 discs in CD mode.In track mode, pressSEEK, SEEK to scroll through all tracks onthe discIn folder mode, pressS

5. SEEK: In radio and CD/MP3mode, press to access the previous() or next ( ) strong stationor track.In satellite radio mode (if equipped), pressSEEK t

8. FOLDER : In folder mode,press FOLDERto access nextfolder on MP3 discs, if available.9.FOLDER: In folder mode,press FOLDER to access theprevious fol

CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The

In CATEGORY MODE, press SCAN to hear a brief sampling of thechannels in the selected category. Press again to stop.Satellite radio is available only w

18. (CD eject): To eject a discfrom the system, press. Selectthe correct slot number usingmemory presets 1–6. When ready, the system will eject the di

Required equipment:1. Any portable music player designed to be used with headphones2. An audio extension cable with stereo male 1/8 in. (3.5 mm)connec

5. For safety reasons, connecting or adjusting the settings on yourportable music player should not be attempted while the vehicle ismoving. Also, the

• Station overload: When you pass a broadcast tower, a stronger signalmay overtake a weaker one and play while the weak station frequencyis displayed.

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

Satellite radio reception factors: To receive the satellite signal, yourvehicle has been equipped with a satellite radio antenna located on theroof of

Satellite Radio Electronic Serial Number (ESN): This 12–digitSatellite Serial Number is needed to activate, modify or track yoursatellite radio accoun

Radio Display Condition Action RequiredNO TEXT Song titleinformation notavailable.Song title information notavailable at this time on thischannel. The

SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele

• Remove any snow, ice or leaves from the air intake area at the base ofthe windshield.• To improve the A/C cool down when the vehicle interior issign

DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEM(IF EQUIPPED)1. A/C control: Press to turn onthe air conditioning. Press again toturn off the air cond

4. MAX A/C: Distributesrecirculated air through theinstrument panel vents to cool thevehicle. This recooling of theinterior air is more economical and

14. Driver’s side temperaturecontrol: Press to increase ordecrease the temperature on thedriver side of the cabin. This controlalso sets the passenger

For maximum cooling performance:• Select and A/C and recirculated air. Use recirculated air with A/C toprovide a cooler airflow.• Move the temperature

HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola

Fog lamp controlThe fog lamps can be turned ononly when the headlamp control isin the, or position andthe high beams are not turned on.Pull headlamp c

Flash to passPull the lever toward you toactivate. Release the lever todeactivate.PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument pa

To adjust the headlamps:1. Park your vehicle on a level surface about 25 feet (7.6 meters) awayfrom a vertical plain surface (3). Check your headlamp

PERCHLORATE MATERIALCertain components of this vehicle such as airbag modules, seat beltpretensioners, and button cell batteries may contain Perchlora

TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.INTERIOR LAMPSMap lampsThe front map lamps a

Examples of acceptable condensation are:• Presence of thin mist (no streaks, drip marks or droplets)• Fine mist covers less than 50% of the lensExampl

Function Number of bulbs Trade numberAshtray lamp 1 161Visor vanity lamp - Slideon rail system (SOR)2A6224PFAll replacement bulbs are clear in color e

WARNING: Handle a halogen headlamp bulb carefully and keepout of children’s reach. Grasp the bulb only by its plastic baseand do not touch the glass.

Replacing tail/brake/turn/backup lamp bulbs1. Turn the headlamp switch off andopen the tailgate.2. Remove the two bolts from thelamp assembly.3. Remov

Replacing license plate lamp bulbsThe license plate bulbs are locatedbehind the rear bumper. To changethe license plate lamp bulbs:1. Reach behind the

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

TILT STEERING COLUMNPull the lever down and release, tounlock the steering column tilt lock.With the lever in the down position,tilt the steering colu

Slide on rod featureRotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage.Note: To stow the visor back intoth

Installing a garage door opener (if equipped)The storage compartment can be converted to accommodate a variety ofaftermarket garage door openers:• Pla

Service Data RecordingService data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This pote

AUXILIARY POWER POINTS (12VDC)Power outlets are designed for accessory plugs only. Do not insertany other object in the power outlet as this will dama

Truck bed auxiliary power pointAn additional auxiliary power pointis located in the bed of the truck(12V 20AMP max).Lift the cover to access the auxil

WARNING: When closing the power windows, you should verifythey are free of obstructions and ensure that children and/orpets are not in the proximity o

If the switch is pressed and held to the normal open or ONE TOUCHDOWN position during a ONE TOUCH UP event, the window will stop. If,after 1/2 second

The power down back window only has three window position selections:• Fully open• Vent• Fully closedPress and release thecontrol toopen window to the

Security overrideIf, during a bounce-back condition and within two seconds after thewindow stops, the control is held in the closed direction, the bac

Without microphoneWith microphoneThe mirror will automatically return to the normal state whenever thevehicle is placed in R (Reverse) to ensure a bri

Fold-away mirrorsFold the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash.Heated outside mirrors(if equipped)B

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED)The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is

3. Press the SET + control andrelease it.4. Take your foot off the acceleratorpedal.5. The indicator lighton theinstrument cluster will turn on.Note:•

and/or other details about the vehicle or crash to assist 911 operators toprovide the most appropriate emergency services. If you do not want todisclo

Increasing speed while using speed controlThere are two ways to set a higherspeed:• Press and hold the SET + controluntil you get to the desiredspeed,

• Press the speed control OFFcontrol.Note: When you turn off the speedcontrol or the ignition, your speedcontrol set speed memory is erased.STEERING W

In any mode:• Press VOL + or − to adjustvolume.Navigation system hands freecontrol features (if equipped)Press and hold VOICE briefly untilthe voiceic

Navigation system/SYNC handsfree control features(if equipped)Press VOICE briefly until thevoiceicon appears on theNavigation display to use the voice

Bounce-back: When an obstacle has been detected in the moon roofopening as the moon roof is closing, the moon roof will automaticallyopen and stop at

Info menuThis menu displays the following control displays:• Odometer/Trip Odometer (Trip A and Trip B)• Distance to Empty• Average Fuel Economy• Setu

• Variations in top-off procedure from one fill-up to another• Rounding of the displayed values to the nearest 0.1 gallon (liter)1. Drive the vehicle

AWD lockSelect this function from the SETUP MENU to display the AWD lockedfunction.1. Press the SELECT/RESET controlfor the current display mode.2. Pr

Units (English/Metric)1. Select this function from theSETUP MENU for the current unitsto be displayed.2. Press and hold theSELECT/RESET control switch

AutolockThis feature automatically locks all vehicle doors when the vehicle isshifted into any gear and when the vehicle is in motion over 13 mph(20 k

Cell phone useThe use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,dri

Trailer sway controlThis feature uses the electronic stability control to mitigate trailer sway,1. To disable/enable the trailer swayfeature, select t

Compass display (if equipped)The compass heading is displayed as one of N, NE, E, SE, S, SW, W andNW in the message center display.The compass reading

4. Press and hold the reset buttonon the compass module forapproximately four seconds untilCOMPASS ZONE XX appears in themessage center display.5. Con

System warningsSystem warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems.In the event of a multiple warning si

Warning display StatusRemove objects near pass seat Warning returns after thecondition has cleared thenreoccurs within the sameignition on-off cycle.C

TIRE PRESSURE MONITOR FAULT — Displayed when the TirePressure Monitoring System is malfunctioning. If the warning stays on orcontinues to come on, hav

OPTIONAL MESSAGE CENTER (IF EQUIPPED)With the ignition in the on position,the message center, located on yourinstrument cluster, displaysimportant veh

Info menuThe Info menu items are shown onthe top two lines of the messagecenter. Press the INFO control todisplay the following:• Trip odometer (Trip

Average fuel economy (AFE)Select this function from the INFOmenu to display your average fueleconomy in miles/gallon or liters/km.If you calculate you

Fuel UsedSelecting this function from theINFO menu. “FUEL USED XXX.XGAL” will display the fuel used sincelast reset. The information displayedwill be