Ford 2010 Explorer v.2 User Manual

Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 18Message center 21Entertainment Systems 39How to get going 39AM/FM stereo with

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

• Remove any snow, ice or leaves from the air intake area at the base ofthe windshield.• To improve the A/C cool down when the vehicle interior issign

DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEM(IF EQUIPPED)1. A/C control: Manually turns A/Con or off.2. Recirculation control: Coolsthe vehicle mo

5. DUAL (Single/dual electrictemperature control): Allows thedriver to have full control of thecabin temperature settings (single zone) or allows the

15. Fan Speed: Manually increasesor decreases the fan speed.16. EXT: Displays the outside airtemperature. It will remaindisplayed until the EXT contro

To allow side window defogging and demisting while warming up thevehicle cabin:1. Select.2. Select A/C.3. Set the temperature control to maintain comf

FLOOR CONSOLE CLIMATE CONTROLSControls the direction of the airflowto the rear of the vehicle.•directs air flow primarilythrough the console panelregi

HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola

Fog lamp controlThe fog lamps can be turned ononly when the headlamp control isin the, or position andthe high beams are not turned on.Pull headlamp c

Flash-to-passPull the lever toward you toactivate. Release the lever todeactivate.PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument pa

To adjust the headlamps:1. Park your vehicle on a level surface about 25 feet (7.6 meters) awayfrom a vertical plain surface (3). Check your headlamp

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.INTERIOR LAMPSDome/reading lampsThe dome lam

Cargo/reading lampsThe dome portion of the lamp orthe center light can be turned onwhen the panel dimmer control isrotated fully up or when a door iso

Function Number of bulbs Trade numberHeadlamp low & highbeam2H13Front park/turn lamp 2 3457 NAK (amber)Side park/turn lamp 2 194Upper rear tail la

Replacing headlamp bulbsDo not touch the glass of a halogen bulb.1. Turn off the headlamps and openthe hood.2. Remove three screws from theheadlamp as

Replacing front parking lamp/turn signal/sidemarker bulbs1. Turn off the headlamps and openthe hood.2. Remove three screws from theheadlamp assembly a

4. Rotate the bulb socketcounterclockwise and remove itfrom the lamp assembly.5. Pull the bulb straight out of thesocket.Reverse steps to reinstall bu

Replacing high-mount brakelamp bulb1. Remove the two screws and lampassembly away from the vehicle.2. Remove the bulb holder from thelamp assembly by

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

O (off) — Rear wiper and washer off.For rear wash cycle, rotate (and hold as desired) the rear wiper/washercontrol to eitherposition.From either posit

Slide-on-rod featureRotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage.Note: To stow the visor back intoth

WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may

Installing a garage door opener (if equipped)The storage compartment can be converted to accommodate a variety ofaftermarket garage door openers:1. Pl

WARNING: Use only soft cups in the cupholder. Hard objectscan injure you in a collision.Rear center console features (if equipped)The rear center cons

To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe ba

To operate one-touch down:• Press the switch completely downto the second detent and releasequickly. The window will openfully. Momentarily press thes

Window lockThe window lock feature allows onlythe driver to operate the powerwindows.To lock out all the window controls(except for the driver’s) pres

EXTERIOR MIRRORSPower side view mirrorsWARNING: Do not adjust the mirror while the vehicle is inmotion.The ignition must be in the accessory or on pos

Fold-away mirrorsFold the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash.POWER ADJUSTABLE FOOT PEDALS (IF EQU

Manual power deploy:To manually operate the running boards, refer to Message center in theInstrument Cluster chapter.• This feature can manually set t

WARNING: Turn off the running boards before jacking orplacing any object under the vehicle. Never place your handbetween the extended running board an

• If the vehicle speed decreases more than 10 mph (16 km/h) belowyour set speed on an uphill, your speed control will disengage.Resuming a set speedPr

Service engine soon: The serviceengine soon indicator lightilluminates when the ignition is firstturned to the on position to checkthe bulb and to ind

Reducing speed while using speed controlThere are two ways to reduce a setspeed:• Press and hold the SET - controluntil you get to the desiredspeed, t

STEERING WHEEL CONTROLSThese controls allow you to operate some radio control features.Audio control featuresPress MEDIA to select:• AM, FM1, FM2• SAT

In any mode:• Press VOL + or − to adjustvolume.Navigation system hands freecontrol features (if equipped)Press and hold VOICE briefly untilthe voiceic

Navigation system/SYNC威 handsfree control features (ifequipped)Press VOICE briefly until thevoiceicon appears on theNavigation display to use the voic

Bounce-back: When an obstacle has been detected in the moon roofopening as the moon roof is closing, the moon roof will automaticallyopen and stop at

Car2U威 Home AutomationSystemHomeLink姞 Wireless Control System (if equipped)The HomeLink威 Wireless Control System, located on the overheadconsole or on

Console mountVisor mount1. Position the end of your hand-held transmitter 1–3 inches (2–8 cm)away from the HomeLink威 button you wish to program while

4. At the garage door opener receiver (motor-head unit) in the garage,locate the “learn” or “smart” button (usually near where the hangingantenna wire

After completing Step 1 outlined in the Programming section, replaceStep 2 with the following:Note: If programming a garage door opener or gate operat

Erasing HomeLink姞 buttonsConsole mountVisor mountTo erase the three programmed buttons (individual buttons cannot beerased):• Press and hold the two o

• Optional instrument clusterBrake system warning light: Toconfirm the brake system warninglight is functional, it willmomentarily illuminate when the

Car2U姞 Home Automation System (if equipped)The Car2U威 Home AutomationSystem is a universal transmitterlocated in the driver’s visor thatincludes two p

• Fixed code garage door openers were produced prior to 1996. Fixedcode uses the same coded signal every time. It is manuallyprogrammed by setting DIP

2. Go to the garage to locate thegarage door opener motor and its“learn” button. You may need aladder to reach the unit and youmay need to remove the

Note: The Car2U威 system allows for three devices to be programmed. Ifyou need to change or replace any of the three devices after it has beeninitially

3. To input these positions into theCar2U威 system, simultaneouslypress all three Car2U威 systembuttons for a few seconds and thenrelease to put the dev

To erase programming on the Car2U威 system (individual buttons cannotbe erased), use the following procedure:1. Firmly press the two outsideCar2U威 syst

WARNING: Do not place any objects on the cargo area cover.They may obstruct your vision or strike occupants of the vehiclein the case of a sudden stop

REAR LIFTGATEThe liftgate area is only intended for cargo, not passengers. You can openand close the liftgate from outside the vehicle. It cannot be o

LUGGAGE RACKYour vehicle is equipped with a roof rack for transporting items on theexterior of the vehicle.The maximum recommended load tobe carried o

WARNING: Loaded vehicles, with a higher center of gravity,may handle differently than unloaded vehicles. Extraprecautions, such as slower speeds and i

Safety belt: Reminds you to fastenyour safety belt. A Belt-Minder威chime will also sound to remind youto fasten your safety belt. Refer tothe Seating a

KEYSOne key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency.Your keys are programmed to your v

Deactivating/activating autolockYour vehicle comes with the autolock feature enabled. There are fourmethods to enable/disable this feature:• Through y

Keyless entry keypad procedure1. Turn the ignition to the off position.2. Close all doors, the liftgate and liftgate window.3. Enter 5–digit entry cod

Power door unlock/lock procedureYou must complete Steps 1-5 within 30 seconds or the procedure willhave to be repeated. If the procedure needs to be r

Power door lock/unlock inhibit feature (if equipped)If the key is not in the ignition, all doors are closed, and the vehicle hasbeen locked using the

CHILDPROOF DOOR LOCKS• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the outside when the

The remote entry system allows youto lock or unlock all vehicle doorsand liftgate, open the liftgatewindow without a key and activatethe panic alarm.T

Locking the doors/liftgate1. Press and release to lock all the doors and liftgate. The lamps willflash. Note: If any door, the liftgate or the liftgat

Activating the memory seat featureTo activate this feature:1. Position the seat and adjustable pedals to the position desired.2. Press the SET control

2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board.3. Remove the old battery.Note: Please refer to localreg

WARNING: Never remove the coolant reservoir cap while theengine is running or hot.Low tire pressure warning:Illuminates when your tire pressureis low.

3. Turn the key from the 1 (off)position to 3 (on).4. Cycle eight times rapidly (within10 seconds) between the 1 (off)position and 3 (on). Note: Theei

SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED)You can use the keyless entrykeypad to:• lock or unlock the doors withoutusing a key.• open the liftgate

• If you program a code to a position that already contains a set code,the previously-set code will be erased.Erasing personal code1. Enter the factor

Your vehicle comes with two coded keys; additional coded keys may bepurchased from your authorized dealer. The authorized dealer canprogram your spare

Automatic disarmingSwitching the ignition to the on position with a coded key disarms thevehicle.• The theft indicator will illuminate for three secon

2. Turn the ignition from the 1 (off)position to the 3 (on) position. Keepthe ignition in the 3 (on) positionfor at least three seconds, but nomore th

SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event o

To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o

To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous

WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Adjusting the front manual seat (if eq

O/D off: Illuminates when theoverdrive function of thetransmission has been turned off;refer to the Driving chapter.AdvanceTrac威: Flashes when theAdva

Using the manual lumbar support (if equipped)For more lumbar support, turn thelumbar support control toward thefront of vehicle.For less lumbar suppor

WARNING: To reduce the risk of possible serious injury: Do nothang objects off seat back or stow objects in the seatback mappocket (if equipped) when

Press the control to recline theseatback forward or rearward.Using the power lumbar support (if equipped)The power lumbar control is located on the ou

A position can be recalled:• in any gearshift position if the ignition is not in the on position.• only in P (Park) or N (Neutral) if the ignition is

Deactivating/activating the easy access/easy out featureThe easy entry/exit feature can be turned off or on through the vehiclemessage center (if equi

Note: Do not do the following:• Place heavy objects on the seat• Operate the seat heater if water or any other liquid is spilled on theseat. Allow the

If needed, when installing some high back child restraints, the headrestraints of the second row seating positions can be removed. Insert athin pointe

1. Lower the head restraints bypulling on the strap.2. Locate the recline handle for your particular seat on the side of theseat cushion by the door.6

Bucket Seats3. Pull up on the handle (pull forward on the bucket seat handle) andpush the seatback forward toward the front of the vehicle.To return t

2. Lift the cargo mode lever locatedon the back of the seatback to kneelthe seat down and get a flat loadingfloor.Returning to the upright position fr

Turn signal: Illuminates when theleft or right turn signal or thehazard lights are turned on. If theindicators stay on or flash faster, check for a bu

60/40 SeatsBucket Seats2. Pull the handle up (pull forward on the bucket seat handle) againuntil the seat releases from the floor.3. Push the seat upw

To return the seat to a seating position:1. Push the seat down and latch tothe floor with a moderate amount ofeffort and speed.2. Make sure the seat i

Exiting the 3rd row1. Lower the head restraints. SeeFolding down the 2nd row seatsearlier in this section.2. Pull on the lever/strap (asequipped) loca

Bucket Seats2. Pull the handle up (pull forward on the bucket seat handle) againuntil the seat releases from the floor.3. Push the seat upward and fol

4. Lift up on the head restraint untilit locks into its original position.WARNING: Before returning the seatback to its originalposition, make sure th

3rd row folding seat (if equipped)Before folding the third row seats,fold the head restraints down bypulling on the strap located underthe restraint.P

The control buttons are located onthe driver-side rear quarter trimpanel (accessible from the liftgatearea).Push the bottom portion of thecontrol butt

WARNING: Before returning the seatback to its originalposition, make sure that cargo or any objects are not trappedbehind the seatback. After returnin

The fact that the pretensioners or airbags did not activate for both frontseat occupants in a collision does not mean that something is wrong withthe

WARNING: Air bags can kill or injure a child in a child seat.NEVER place a rear-facing child seat in front of an active airbag. If you must use a forw

Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature,

Determining if the Personal Safety System™ is operationalThe Personal Safety System™ uses a warning light in the instrumentcluster or a back-up tone t

WARNING: It is extremely dangerous to ride in a cargo area,inside or outside of a vehicle. In a collision, people riding inthese areas are more likely

WARNING: BELT AND RETRACTOR ASSEMBLY MUST BEREPLACED if the safety belt assembly automatic lockingretractor feature or any other safety belt function

All safety restraints in the vehicle are combination lap and shoulderbelts. All of the passenger combination lap and shoulder belts have threetypes of

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl

When the Safety Canopy威 System, seat-mounted side airbags, and/or thefront airbags are activated, the safety belt pretensioners for the driverand righ

Second row comfort guideThe second row outboardlap/shoulder belt is equipped with abelt comfort guide. This guide isattached to the quarter trim panel

Use only extensions manufactured by the same supplier as the safetybelt. Manufacturer identification is located at the end of the webbing onthe label.

Both the driver’s and passenger’s safety belt usages are monitored andeither may activate the Belt-Minder威 feature. The warnings are the samefor the d

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra

Locks and Security 150Keys 150Locks 150Anti-theft system 156Seating and Safety Restraints 166Seating 166Safety restraints 187Airbags 202Child restrain

Trip odometer: Registers the miles (kilometers) of individual journeys.• Standard instrument clusterPress the SELECT/RESET controlonce to switch from

Reasons given... Consider...“I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate

The driver and front passenger Belt-Minder威 features can bedeactivated/activated by performing the following procedure:Before following the procedure,

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right

WARNING: Never place your arm over the airbag module as adeploying airbag can result in serious arm fractures or otherinjuries.To properly position yo

Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt

• one or more impact and safing sensors.• a readiness light and tone.• diagnostic module.• and the electrical wiring which connects the components.• F

The front passenger sensing systemuses a ⬙passenger airbag off⬙ or⬙pass airbag off⬙ indicator which willilluminate and stay lit to remind youthat the

OccupantPass Airbag OffIndicator LampPassenger AirbagEmpty seat Unlit DisabledSmall child in childsafety seat or boosterLit DisabledSmall child with s

ObjectsPass Airbag OffIndicator LampPassenger AirbagSmall (i.e. three-ringbinder, small purse,bottled water)Unlit DisabledMedium (i.e. heavybriefcase,

STANDARD MESSAGE CENTER (IF EQUIPPED)Your vehicle’s message center allowsyou to configure/personalize certainvehicle options to suit your needs.The me

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit.If the airbag readi

A difficulty with the system is indicated by one or more of the following:• The readiness light will eitherflash or stay lit.• The readiness light wil

How does the side airbag system work?The design and development of the side airbag system includedrecommended testing procedures that were developed b

WARNING: Several air bag system components get hot afterinflation. Do not touch them after inflation.WARNING: If the sideairbag has deployed, theairba

WARNING: All occupants of the vehicle including the drivershould always wear their safety belts even when an airbag SRSand Safety Canopy威 System is pr

The Safety Canopy威 System, in combination with safety belts, can helpreduce the risk of severe injuries in the event of a significant side impactcolli

WARNING: If the Safety Canopy威 System has deployed, theSafety Canopy威 will not function again. The SafetyCanopy威 System (including the A, B and C pill

Disposal of airbags and airbag equipped vehicles(including pretensioners)Contact your authorized dealer as soon as possible. Airbags MUST BEdisposed o

Recommendations for Safety Restraints for ChildrenChild size, height, weight, orageRecommendedrestraint typeInfantsortoddlersChildren weighing 40 lb (

Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe

AVERAGE FUEL XX.X MPG / (L/100km)Average fuel economy displays your average fuel economy in miles/gallonor liters/100 km.If you calculate your average

WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli

Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle.If the child is the proper height, age, and weigh

Installing child safety seats with combination lap and shoulderbeltsIf needed, when installing some high back child restraints, the headrestraints of

• Keep the buckle release button pointing up and away from the safetyseat, with the tongue between the child seat and the release button,to help preve

3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi

8. Remove remaining slack from thebelt. Force the seat down with extraweight, e.g., by pressing down orkneeling on the child restraint whilepulling up

method eliminates the need to use safety belts to attach the child seat,however the safety belt can still be used to attach the child seat. Forforward

The LATCH anchors for child seatinstallation are located at the rearsection of the second row seatbetween the cushion and seatback.The LATCH anchors a

WARNING: Depending on where you secure a child restraint,and depending on the child restraint design, you may blockaccess to certain safety belt buckl

Attaching child safety seats with tether strapsMany forward-facing child safety seats include a tether strap whichextends from the back of the child s

• Compass zone adjustment• Compass calibration adjustmentSYSTEM CHECK HOLD RESETPress and hold the SELECT/RESET stem to select system check whenthis i

Perform the following steps to install a child safety seat with tetheranchors:1. Route the tether strap under the head restraint and between the headr

3. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safety seat maynot be retained properly in theeven

Booster seats position a child so that vehicle lap/shoulder safety belts fitbetter. They lift the child up so that the lap belt rests low across the h

Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a

Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary

• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and

TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen

2. Press the SELECT/RESET stem for the next setup menu item or waitfor more than four seconds to return to the info menu.ENGLISH / SPANISH / FRENCH /

Glossary of tire terminology• Tire label: A label showing the OE (Original Equipment) tire sizes,recommended inflation pressure and the maximum weight

Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure of all tires and adjust ifrequired

When weather temperature changes occur, tire inflation pressures alsochange. A 10°F (6°C) temperature drop can cause a corresponding dropof 1 psi (7 k

TIRE CAREInspecting your tires and wheel valve stemsPeriodically inspect the tire treads for uneven or excessive wear andremove objects such as stones

WARNING: AgeTires degrade over time depending on many factors such asweather, storage conditions, and conditions of use (load, speed,inflation pressur

WARNING: Only use replacement tires and wheels that are thesame size, load index, speed rating and type (such as P-metricversus LT-metric or all-seaso

It is recommended that the two front tires or two rear tires generally bereplaced as a pair.The tire pressure sensors mounted in the wheels (originall

vehicle seems to pull to one side when you’re driving, the wheels may beout of alignment. Have an authorized dealer check the wheel alignmentperiodica

Note: Your vehicle may be equipped with a dissimilar spare tire/wheel. Adissimilar spare tire/wheel is defined as a spare tire and/or wheel that isdif

5. 15: Indicates the wheel or rim diameter in inches. If you change yourwheel size, you will have to purchase new tires to match the new wheeldiameter

2. Press and hold the SELECT/RESET stem to turn park aid on or off.3. Press the SELECT/RESET stem for the next setup menu item or waitfor more than fo

numbers represent the week and year the tire was built. For example,the numbers 317 mean the 31st week of 1997. After 2000 the numbersgo to four digit

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

The Tire Pressure Monitoring System complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw

Understanding your Tire Pressure Monitoring System (TPMS)The Tire Pressure Monitoring System measures pressure in your fourroad tires and sends the ti

When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.

Low Tire PressureWarning LightPossible cause Customer Action RequiredFlashing WarningLightSpare tire in use Your temporary spare tire is inuse. Repair

SNOW TIRES AND CABLESWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. The use ofnon-recommende

your vehicle, familiarize yourself with the following terms for determiningyour vehicle’s weight ratings, with or without a trailer, from the vehicle’

Most geographic areas (zones) have a magnetic north compass point thatvaries slightly from the northerly direction on maps. This variation is fourdegr

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

WARNING: Exceeding any vehicle weight rating limitation couldresult in serious damage to the vehicle and/or personal injury.Steps for determining the

to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12x 100) = 1400

TRAILER TOWINGTrailer towing with your vehicle may require the use of a trailer towoption package.Trailer towing puts additional loads on your vehicle

4x2GCWR (Gross Combined Weight Rating)/Trailer WeightEngine Rear axle ratio MaximumGCWR-lb. (kg)Trailer weightrange-lb. (kg)(0-Maximum)4.0L SOHC Class

4X4 and AWDGCWR (Gross Combined Weight Rating)/Trailer WeightEngine Rear axle ratio MaximumGCWR-lb. (kg)Trailer weightrange-lb. (kg)(0-Maximum)4.6L* C

Class III Trailer Hitch Safety ChainLoops can be used as recoveryhooks.Do not attach safety chains to the bumper.Trailer brakesElectric brakes and man

2. Press and release the SELECT/RESET stem to scroll through theinformation menu until the message center displays HOLD RESET FORSETUP MENU.3. Press a

Driving while you towWhen towing a trailer:• To ensure proper “break-in” of powertrain components, do not trailertow during the first 1,000 miles (1,6

• If you will be towing a trailer frequently in hot weather, hillyconditions, at GCWR, or any combination of these factors, considerrefilling your rea

2WD vehicles: Do not tow your vehicle with any wheels on the ground,as vehicle or transmission damage may occur. It is recommended to towyour vehicle

STARTINGPositions of the ignition1. Off— locks the gearshift leverand allows key removal. Thisposition also shuts the engine andall electrical accesso

WARNING: If you smell exhaust fumes inside your vehicle, haveyour dealer inspect your vehicle immediately. Do not drive if yousmell exhaust fumes.Impo

• Make sure the gearshift is in P(Park).3. Turn the key to 3 (on) withoutturning the key to 4 (start).Some warning lights will briefly illuminate. See

Starting the engine1. Turn the key to 3 (on) withoutturning the key to 4 (start). If thereis difficulty in turning the key,rotate the steering wheel u

ENGINE BLOCK HEATER (IF EQUIPPED)An engine block heater warms the engine coolant which aids in startingand allows the heater/defroster system to respo

• Be sure that areas where the vehicle is parked are clean and clear ofall combustibles such as petroleum products, dust, rags, paper andsimilar items

brake pedal pulsation may be observed during ABS braking and thebrake pedal may suddenly travel a little farther as soon as ABS braking isdone and nor

• Some messages can be acknowledged and reset by pressing theSELECT/RESET stem. This allows you to use the full message centerfunctionality by clearin

The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned on) until theparking brake is released.

ADVANCETRAC姞 WITH ROLL STABILITY CONTROL™ (RSC姞)STABILITY ENHANCEMENT SYSTEMWARNING: Vehicle modifications involving braking system,aftermarket roof r

The AdvanceTrac威 with RSC威 system provides the following stabilityenhancement features for certain driving situations:• Traction Control System (TCS),

• The brake pedal may feel stiffer than usual.Traction Control System (TCS)The TCS is a driver aid feature that helps your vehicle maintain tractionof

• Changing lanes on a snow-rutted road• Entering a snow-free road from a snow-covered side street, or viceversa• Entering a paved road from a gravel r

AdvanceTrac威 with RSC威 FeaturesButtonfunctions“Slidingcar”iconRSC威 ESCEnginetractioncontrolBraketractioncontrolDefault atstart-upOff Enabled Enabled E

Disabling Trailer Sway ControlTrailer sway control can be disabled during any key cycle. Refer toMessage center in the Instrument Cluster chapter for

PREPARING TO DRIVEWARNING: Utility vehicles have a significantly higher rolloverrate than other types of vehicles.WARNING: In a rollover crash, an unb

2. Remove the rubber pad at thebottom of the cup holder to locatethe access cap of the floor shifterassembly.3. Using a screwdriver (orequivalent), re

learning process, slightly firmer shifts may occur. After this learningprocess, normal shift feel and shift scheduling will resume.P (Park)This positi

TIRE PRESSURE SENSOR FAULT — Displayed when a tire pressuresensor is malfunctioning, or your spare tire is in use. For moreinformation on how the syst

D (Drive) without OverdriveOverdrive can be deactivated bypressing the transmission controlswitch on the side of the gearshiftlever.• This position al

Forced downshifts• Allowed in D (Overdrive) or Drive.• Press the accelerator to the floor.• Allows transmission to select an appropriate gear.Driving

WARNING: Always set the parking brake fully and make surethe gearshift is latched in P (Park). Turn the ignition to the offposition and remove the key

• O/D (Overdrive) is automatically returned each time the key is turnedoff.3 (Third)Transmission operates in third gear only.Used for improved tractio

REVERSE SENSING SYSTEM (IF EQUIPPED)The reverse sensing system sounds a tone to warn the driver of obstaclesnear the rear bumper when the R (Reverse)

The system detects obstacles within approximately 16 feet (five meters),at speeds above 2.5 mph (4 km/h) behind the rear bumper with adecreased covera

Audible WarningsDistance to Object Warning13 feet (4 meters) to 19.6 feet(6 meters)Slow beepSpeed below 2.5 mph (4 km/h)up to 1.4 feet (.4 meters) Sol

Four–wheel drive (4WD) supplies power to all four wheels. Do not use4X4 High or 4X4 Low on dry, hard surfaced roads. Doing so will produceexcessive no

Shifting between 4X4 AUTO (4WD Auto) and 4X4 HIGH (4WD High)• Select 4X4 AUTO (4WD Auto) or 4X4 HIGH (4WD High) at anyforward speed.Note: Do not perfo

Normal operation (4.6L engine vehicles only)During normal operation the AWD system is in AWD AUTO mode (AWDLOCKED will illuminate in the message cente

Customer Assistance 335Reporting safety defects (U.S. only) 341Reporting safety defects (Canada only) 341Cleaning 342Maintenance and Specifications 35

OPTIONAL MESSAGE CENTER (IF EQUIPPED)Your vehicle’s message center allowsyou to configure/personalize certainvehicle options to suit your needs.The me

You should either know the terrain or examine maps of the area beforedriving. Map out your route before driving in the area. To maintainsteering and b

If your vehicle gets stuckIf your vehicle gets stuck in mud or snow it may be rocked out byshifting between forward and reverse gears, stopping betwee

WARNING: Vehicles with a higher center of gravity such asutility and four-wheel drive vehicles handle differently thanvehicles with a lower center of

WARNING: If the parking brake is fully released, but the brakewarning lamp remains illuminated, the brakes may not beworking properly. See your author

If the transmission, transfer case or front axle are submerged in water,their fluids should be checked and changed, if necessary.Driving through deep

Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;

WARNING: If you are driving in slippery conditions that requiretire cables, then it is critical that you drive cautiously. Keepspeeds down, allow for

DRIVING THROUGH WATERIf driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive th

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsIn Canada, for uninterrupted Roadside Assistance co

Refer to UNITS later in this section to switch the display from Metric toEnglish.MILES (km) TO EThis displays an estimate of approximately how far you

Note: With extended use, the flasher may run down your battery.FUEL PUMP SHUT-OFF SWITCHFUELRESETThe fuel pump shut-off switch is a device intended to

Standard fuse amperage rating and colorCOLORFuseratingMini fusesStandardfusesMaxi fusesCartridgemaxi fuses2A Grey Grey — —3A Violet Violet — —4A Pink

The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingProtected Circuits1 20A Moon roof, Adjustable pedals,Memory seats, Lumbar motor2 5A Mic

Fuse/RelayLocationFuse AmpRatingProtected Circuits12 5A Rear wiper motor RUN/ACC,Trailer battery charge relay inPDB, Radio13 15A Heated mirror, Manual

The following relays are located on either side of the passengercompartment fuse panel. See your authorized dealer for service of theserelays.Fuse/Rel

The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingProtected Circuits1 50A** Battery feed 2 (passengercompartment fuse panel)

Fuse/RelayLocationFuse AmpRatingProtected Circuits25 20A* Front power point/Cigar lighter26 20A* 4x4 module (4.6L engine only)27 20A* 6R Transmission

Fuse/RelayLocationFuse AmpRatingProtected Circuits43 15A* Coil on plug (4.6L engine only),Coil tower (4.0L engine only)44 15A* Injectors45B — Not used

WARNING: The use of tire sealants may damage your TirePressure Monitoring System and should not be used.WARNING: Refer to Tire Pressure Monitoring Sys

• Use more than one dissimilar spare tire at a time• Use commercial car washing equipment• Try to repair the dissimilar spare tireUse of one of the di

FUEL ECONOMY MPG (L/km)This displays instantaneous fuel economy as a bar graph ranging from ↓poor economy to ↑ excellent economy.Your vehicle must be

Stopping and securing the vehicle1. Park on a level surface, activatethe hazard flashers and set theparking brake.2. Place gearshift lever in P (Park)

Removing the jack and tools1. Open liftgate and remove thecarpeted floor lid.2. Turn jack screw eyelet (1)counterclockwise to releasepressure.3. Rotat

2. Insert the lug wrench on thewinch drive nut.The wrench will stop moving andforward resistance to turning will befelt when properly engaged.3. Turn

WARNING: If the vehicle slips off the jack, you or someone elsecould be seriously injured.WARNING: Do not attempt to change a tire on the side of thev

4. Assemble the jack handleextension on the lug nut wrench bysliding the square end of the jackhandle through the plastic grommeton the lug nut wrench

WARNING: To lessen therisk of personal injury, donot put any part of your bodyunder the vehicle while changing atire. Do not start the engine whenyour

increases significantly and the spare tire carrier ratchets or slips whenthe tire is raised to the maximum tightness. Tighten to the best of yourabili

WARNING: When a wheel is installed, always remove anycorrosion, dirt or foreign materials present on the mountingsurfaces of the wheel or the surface

JUMP STARTINGWARNING: The gases around the battery can explode ifexposed to flames, sparks, or lit cigarettes. An explosion couldresult in injury or v

Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,

4. DOOR AJAR5. EXTERIOR LAMP6. BRAKE FLUID LEVEL7. PARK BRAKE8. FUEL LEVEL AND DISTANCE TO EMPTYAWD AUTO / LOCKED (if equipped)This feature disables/e

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to the g

Note: Do not attach the negative (-) cable fuel lines, engine rockercovers, the intake manifold or electrical components as groundingpoints.WARNING: D

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGNote: Turn off the power running boards (if equipped) prior topreparing the vehicle for towing. Refer to Power deployable runningboards

On 4x4/AWD vehicles, it is required that your vehicle be towed with awheel lift and dollies or flatbed equipment with all the wheels off theground.If

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized

In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph

In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext

procedure outlined on the first page of the Customer Assistance section,you may be eligible to participate in the BBB AUTO LINE program.The BBB AUTO L

The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have

Press the RESET button to turn autounlock on or off.RUNNING BRDS (if equipped)This feature automatically deploys the side running boards for easyentry

If you are in another foreign country, contact the nearest authorizeddealer. If the authorized dealer employees cannot help you, they candirect you to

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i

WAXING• Wash the vehicle first.• Do not use waxes that contain abrasives; use Motorcraft威 PremiumLiquid Wax (ZC-53-A), which is available from your au

ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when

4.6L V8 ENGINEPLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your authorized

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft威 Premium Windshield Washer Concentrate (ZC-32-A),available from your a

If a staining liquid like coffee/juice has been spilled on the instrumentpanel or on interior trim surfaces, clean as follows:1. Wipe up spilled liqui

LEATHER SEATS (IF EQUIPPED)Your leather seating surfaces have a clear, protective coating over theleather.• For routine cleaning, wipe the surface wit

Motorcraft威 Premium Glass Cleaner (Canada only) (CXC-100)Motorcraft威 Premium Liquid Wax (ZC-53-A)Motorcraft威 Premium Windshield Washer Concentrate (U.

Usually, when something affects the compass readings, the compass willcorrect itself after a few days of operating your vehicle in normalconditions. I

SERVICE RECOMMENDATIONS• Use the scheduled maintenance information to track routineservice.• Use only recommended fuels, lubricants, fluids and servic

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.0L V6 engine1. Engine oil filler cap2. Engine oil dipstick (out of view)3. Brake fluid reservoir4. P

4.6L V8 engine1. Air filter assembly2. Engine oil filler cap3. Engine oil dipstick4. Brake fluid reservoir5. Power distribution box6. Battery7. Power

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

CHANGING THE WIPER BLADES1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to releas

4. To attach the new wiper to thewiper arm, align the cross pin andkeyway (denoted with the arrows)and firmly press the wiper bladeinto the wiper arm

• 4.6L V8 engine6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.• If the oil level is between the lower and upper holes, t

• 4.6L V8 engine• Oil levels above the upper hole may cause engine damage. Some oilmust be removed from the engine by an authorized dealer.7. Put the

Engine oil and filter recommendations4.0L V6 EngineLook for this certificationtrademark.Use SAE 5W-30 engine oilOnly use oils “Certified For Gasoline

HOLD RESET IF NEW OILTo reset the oil monitoring system to 100% after each oil change(approximately 7,500 miles [12,000 km] or six months) perform the

4.6L 3V V8 EngineLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils “Certified For Gasoline Engines” by the AmericanPetroleum

BATTERYYour vehicle is equipped with aMotorcraft威 maintenance-freebattery which normally does notrequire additional water during itslife of service.If

WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

• 4.0L V6 engine• 4.6L V8 engine• The engine coolant should be at the FULL COLD level or within theCOLD FILL RANGE as listed on the engine coolant res

Adding engine coolantWhen adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to the coolant reservo

For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when

If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your authorized dealer check the engine cooling system.Your coolin

• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures i

Along with the (engine coolant temperature) indicator, the enginecoolant temperature gauge will read in the H (Hot) area.Oil overheat can be triggered

REMOVE OBJECTS NEAR PASS SEAT — Displayed when objectsare by the passenger seat. After the objects are moved away from theseat, if the warning stays o

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsWARNING: Do not overfill the fuel tank. The pressure in anoverfilled tank may c

• Fuels can also be harmful if absorbed through the skin. If fuel issplashed on the skin and/or clothing, promptly remove contaminatedclothing and was

• Keep the fuel pump nozzle in contact with the fuel container whilefilling.• DO NOT use a device that would hold the fuel pump handle in the fillposi

WARNING: The fuel system may be under pressure. If you heara hissing sound near the fuel filler door (Easy Fuel™ “no cap”fuel system), do not refuel u

Fuel qualityIf you are experiencing starting, rough idle or hesitation driveabilityproblems, try a different brand of unleaded gasoline. If the proble

Refilling with a portable fuel containerWith the Easy Fuel™ “no cap” fuel system, use the following directionswhen filling from a portable fuel contai

ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform

Calculating fuel economy1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers).2. Each time you fill the tan

• You may want to turn off the speed control in hilly terrain ifunnecessary shifting between the top gears occurs. Unnecessaryshifting of this type co

EPA fuel economy estimatesEvery new vehicle should have a sticker on the window called theMonroney Label which contains EPA fuel economy estimates. Co

BRAKE FLUID LEVEL LOW — Indicates the brake fluid level is lowand the brake system should be inspected immediately. Refer to Brakefluid in the Mainten

WARNING: Exhaust leaks may result in entry of harmful andpotentially lethal fumes into the passenger compartment.Do not make any unauthorized changes

If the service engine soon indicator remains on, have your vehicleserviced at the first available opportunity. Although some malfunctionsdetected by t

POWER STEERING FLUIDCheck the power steering fluid. Refer to scheduled maintenanceinformation.1. Start the engine and let it rununtil it reaches norma

TRANSMISSION FLUIDChecking automatic transmission fluidThe automatic transmission does not have an underhood transmissionfluid dipstick.Refer to your

3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening.Use only fluid that meets Ford specifications

Changing the air filter element• 4.0L Engine• 4.6L Engine1. Release the clamps that secure the air filter housing cover.2. Carefully separate the two

MOTORCRAFT PART NUMBERSComponent 4.0L V6 engine 4.6L 3V V8 engineAir filter element FA-1695 FA-1780Fuel filter FG-1083 FG-1083Battery BXT-65-650 BXT-6

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord Part Name orequivalentFord Part Number / FordSpecificationBrake fluidBetween MINand

Item CapacityFord Part Name orequivalentFord Part Number / FordSpecificationEngine coolant(4.0L engine withoutauxiliary climatecontrol)12.2 quarts(11.

Item CapacityFord Part Name orequivalentFord Part Number / FordSpecificationEngine oil(4.0L engine)5.0 quarts(4.7L)•Motorcraft威 SAE5W-30 PremiumSynthe

AUDIO SYSTEMSQuick start — How to get goingWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly

Item CapacityFord Part Name orequivalentFord Part Number / FordSpecificationAutomatictransmission(5R55S) fluid12.7 quarts(12.0L)3Motorcraft威MERCON威 VA

Item CapacityFord Part Name orequivalentFord Part Number / FordSpecificationFuel tank22.5 gallons(85.2L)——1Add the coolant type originally equipped in

ENGINE DATAEngine 4.0L V6 engine 4.6L 3V V8engineCubic inches 245 281Required fuel 87 octane 87 octaneFiring order 1-4-2-5-3-6 1-3-7-2-6-5-4-8Ignition

IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli

The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of

Peace of mindKeyless entry keypadRemote startVehicle security systemsLocking gas plug for capless fuel systemWheel locksFor maximum vehicle performanc

FORD ESP EXTENDED SERVICE PLANSMore than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP. It is the on

Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With

Ford Extended Service Plan3992010 Explorer (exp)Owners Guide, 2nd PrintingUSA (fus)

CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The

Listening to satellite radio (if equipped)1. If the audio system is turned off,press VOL-PUSH to turn the radioon. Turn VOL-PUSH to adjust thevolume.N

AAccessory delay ...124AdvanceTrac ...281Air cleaner filter ...384–386Air conditioning ...

Child safety seats - boosterseats ...232Cleaning your vehicleengine compartment ...344instrument pa

idle speed control ...361lubrication specifications ...387refill capacities ...387service points ...

How to get going ...39IIgnition ...273, 392Illuminated visor mirror ...118Infant seats(see Sa

Oil (see Engine oil) ...356PParking brake ...279Parts(see Motorcraft威 parts) ...386Passenger OccupantC

SecuriLock passive anti-theftsystem ...162Setting the clockAM/FM single CD ...45AM/FM/In-dash 6

Washer fluid ...354Water, Driving through ...307Windows...157power...

For a single CD system, if a discis not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the

Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engageshuffle mode right away, press SEEK to begin random pl

AM/FM Single CD/MP3 satellite compatible sound system(if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and

In CATEGORY MODE, press / to scroll through the list ofavailable SIRIUS威 channel Categories (Pop, Rock, News, etc.). Refer toCategory Mode under Menu

• DELETE SONG: Press OK to delete a song from the system’smemory. Press/ to cycle through the saved songs. When thesong appears in the display that yo

To activate, press MENU repeatedly until RBDS (ON/OFF) appears inthe display. Use / / SEEK to toggle RBDS ON/OFF. WhenRBDS is OFF, you will not be abl

TRACK/FOLDER MODE: Available only on MP3 discs in CD mode.In track mode, pressSEEK, SEEK to scroll through all tracks onthe discIn folder mode, pressS

6. / (Play/Pause): Thiscontrol is operational in CD andDVD mode (if equipped). When aCD or DVD is playing in the FES system, press this control to pla

PRESET # SAVED appears in the display. You can save up to 18 stations,six in AM, six in FM1 and FM2.In satellite radio mode (if equipped), there are 1

Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti

16. CD: Press to enter CD/MP3mode. If a CD/MP3 is already loadedinto the system, CD/MP3 play willbegin where it ended last. If no CD is loaded, NO DIS

Accessory delay: Your vehicle is equipped with accessory delay. Withthis feature, the window switches, radio and moon roof (if equipped)may be used fo

• SAVE SONG: Press OK to save the currently playing song’s title inthe system’s memory. (If you try to save something other than a song,CANT SAVE will

AUTOSET: Press MENU until the display reads AUTOSET. Autosetallows you to set the strongest local radio stations without losing youroriginal manually

The default setting is off; increasing your vehicle speed will not changethe volume level.Adjust 1–7: Increasing this setting from 1 (lowest setting)

If your vehicle is equipped with a Family Entertainment System (FES)please refer to the Family Entertainment DVD system later in thischapter.If your v

Note: In track mode, all tracks on the current disc will shuffle inrandom order. In MP3 folder mode, the system will randomly play alltracks within th

Press and hold to hear a brief sampling of the next channels. Press againto stop.In CATEGORY MODE, press SCAN to hear a brief sampling of thechannels

18. (CD eject): To eject a discfrom the system, press . Selectthe correct slot number usingmemory presets 1–6. When ready, the system will eject the d

Required equipment:1. Any portable music player designed to be used with headphones2. An audio extension cable with stereo male 1/8 in. (3.5 mm)connec

Do not add friction modifier compounds or special break-in oils sincethese additives may prevent piston ring seating. See Engine oil in theMaintenance

5. For safety reasons, connecting or adjusting the settings on yourportable music player should not be attempted while the vehicle ismoving. Also, the

• Station overload: When you pass a broadcast tower, a stronger signalmay overtake a weaker one and play while the weak station frequencyis displayed.

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m

Radio Display Condition Action RequiredNO TEXT Song title informationnot available.Song title informationnot available at thistime on this channel.The

Your vehicle may be equipped with a Family Entertainment System(FES) which allows you to listen to audio CDs, MP3 discs, watch DVDsand to plug in and

Note (navigation-based radiosystems only): Whenadiscisinserted, the FES switches todual-play mode–rear speakers turn off, and headphones turn on. Tosw

Note (navigation-based radiosystems only): Whenadiscisinserted, the FES switches todual-play mode–rear speakers turn off, and headphones turn on. Tosw

Your vehicle is not equipped with the Ford Ambulance PreparationPackage.NOTICE TO OWNERS WITH 20 INCH WHEELS AND TIRESWhen equipped with 20 inch wheel

3. Connect an auxiliary audio/videosource by connecting RCA cords(not included) to the RCA jacks onthe left hand side of the system.• Yellow (1) — vid

4. Press MEDIA to change the audio source of the active channel (A orB). The audio source will be shown on the display. You may change theactive chann

Using wired headphones (not included):WARNING: Do not leave children unattended in the vehicle anddo not let children operate the system while unsuper

DVD player controls1. Headphone control A/B: Whilein Dual Play mode, press to selecteither the A or B headphone source.Then press MEDIA to select thed

4. (Fast forward): Press andrelease for the next chapter ortrack. Press and hold to forwardsearch a DVD, Video CD, or FES CD in DVD/CD mode.5./ (Play/

11. / (Headphones/Speakers): Press once for Dual Play(Headphone mode- the rear speakers are muted) and press again forSingle Play (same media playing

Remote controlUnless otherwise stated, all operations can be carried out with theremote control. Always point the remote control directly at the playe

7. VOL (Volume): When in Single Play, press to increase ( )ordecrease () the volume over all speakers. When in Dual Play, press toincrease () or decre

21. LANGUAGE (DVD dependent): Press to select the desiredlanguage.22. ENTER: Press to select the highlighted menu option.23. ILLUMINATION: Press to il

HeadphonesWireless headphonesWARNING: The driver should never use the headphones whiledriving the vehicle. Using headphones may prevent the driverfrom

• how far (if at all) the driver was depressing the acceleratorand/or the brake pedal;• how fast the vehicle was traveling;• where the driver was posi

To install the batteries, remove the screw at the bottom of the cover.Then, lightly press down on top and slide the cover off.When replacing the batte

To operate the headphones:• Press POWER on the ear piece to turn on the headphones. A redindicator light will illuminate indicating the headphones are

Wired headphonesWARNING: Do not leave children unattended in the vehicle anddo not let children operate the system while unsupervised. Ifwired headpho

Single Play: Single play consists of all occupants in the vehicle listeningto the same playing media over the front and rear speakers. When theDVD sys

Press MEDIA to change the audiosource for Channel A. Thisinformation will display on the DVDsystem screen.Press the Headphone Control buttonB to chang

Press MEDIA to change the audiosource for Channel A. Thisinformation will display on the DVDsystem screen.Press the Headphone Control buttonB to chang

Menu modePress MENU once on the DVD system to access the DVD disc menu ifavailable.Press MENU twice to access the DVD set-up menu and the followingfea

You can select from: WIDE, LETTERBOX or PAN SCAN. Once you havemade your selection, press ENTERto confirm. The LCD screen displaywill immediately chan

Once you have made your selection,press ENTER to confirm. This isdisc dependent.Audio CDsTo play audio CDs on your DVD system:1. Ensure that the vehic

4. The folder, track and elapsedtime will appear in the status bar.The screen will list the Artist, Title,Album and File Name.COMP (Compression):Compr

CELL PHONE USEThe use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,dri

CD, MP3 and CD player care• Handle discs by their edges only. Never touch the playing surface.• Do not expose discs to direct sunlight or heat sources

4. Use the DVD bezel controls to:Press to play or pause a DVD.Press to stop or eject a DVD.Press and release to go to theprevious chapter. Press and h

2. Press the right cursor button. TheDVD will advance one frame. Eachpress of the right cursor button willadvance the DVD video by oneframe.Headphone/

Audio displaysYour DVD system interacts closely with the front audio system. Statusmessages will appear in the radio display showing the DVD status. S

When the DVD system is ON, youcan then press the memory presetcontrols 2 and 4 simultaneously totoggle between Single Play and Dual Play. In Single Pl

Safety informationWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdrivers us

Do not operate video games or video equipment if the power cordsand/or cables are broken, split or damaged. Carefully place cords and/orcables where t

Humidity and moisture condensationMoisture in the air will condense in the DVD player under extremelyhumid conditions or when moving from a cold place

While operating in Headphone Only Mode, the system will have limitedfunctionality.• The system will only output audio to the headphones. It will not b

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele