Introduction 4Instrument Cluster 20Warning lights and chimes 20Gauges 25Message center 27Entertainment Systems 36AM/FM stereo with CD/MP3 36Auxiliary
Frequently asked questionsQuestion AnswerWhat are the series of clicks fromthe cargo area when I first turnthe key in the ignition?The high voltage ba
3. Press and release the RESET button. HOLD RESET TO CONFIRMCLEAR is displayed.4. Press and hold the RESET button for two seconds until ALL MYKEYSCLEA
Note: For all vehicles with remote start installed, it is possible toprogram all original vehicle keys as MyKeys威, in which case, you willneed to use
Condition Potential CausesCannot clear MyKey威 • Key in the ignition is a MyKey威• No MyKeys威 are programmed to thevehicle. Refer to Create a MyKey威sect
POWER DOOR LOCKS• Press thecontrol to unlock alldoors.• Press thecontrol to lock alldoors.Door key unlocking/lockingUnlocking the doorsTurn the key in
Note: The autolock feature can be activated/deactivated independentlyof the autounlock feature.Before following the activation or deactivation procedu
Message center procedureFor information on activating/deactivating the autolock feature using thevehicle’s message center, refer to Message center inf
1. Place the key in the ignition andturn the ignition to the on position.2. Press the power door unlockcontrol on the door panel threetimes.3. Turn th
CHILDPROOF DOOR LOCKSWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thechi
The IKT allows you to:• remotely unlock the vehicledoors.• remotely lock all the vehicledoors.• remotely open the power liftgateglass.• activate the p
Switching from two step to one step door unlockingUnlocking can be switched between two step and one step doorunlocking by pressing and holding bothan
Question AnswerWhy does my engine stay ONwhen it’s extremely cold outside?In order to ensure that the climatecontrol system can begin heatingthe cabin
Replacing the batteryThe integrated keyhead transmitter uses one coin type three-volt lithiumbattery CR2032 or equivalent.To replace the battery:1. Tw
Illuminated entryThe interior lamps, parking lamps and puddle lamps (if equipped)illuminate when the Integrated Keyhead Transmitter or the keyless ent
2. Within five seconds press the 1 • 2 on the keypad. The doors will lockand then unlock to confirm that the system is in programming mode.3. Enter yo
Unlocking and locking the doors and liftgate using keyless entryTo unlock the driver’s door, enter the factory set 5-digit code or yourpersonal code.
Anti-theft indicatorThe anti-theft indicator is located in the instrument panel cluster.• When the ignition is in the offposition, the indicator will
Replacement of integrated keyhead transmitters (IKT) and codedkeysNote: Your vehicle comes equipped with two integrated keyheadtransmitters (IKTs). Th
Please read and understand theentire procedure before you begin.1. Insert the first previouslyprogrammed coded key into theignition.2. Turn the igniti
FRONT SEATSWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the eve
The adjustable head restraintsconsist of:• a trimmed energy absorbing foamand structure (1),• two steel stems (2),• a guide sleeve adjust/releasebutto
WARNING: The adjustable head restraint is a safety device.Whenever possible it should be installed and properly adjustedwhen the seat is occupied.To r
Question AnswerWhat is the fan noise I hear fromthe rear of my hybrid?The fan noise comes from two fanslocated inside the high voltagebattery. These f
Properly adjust the head restraint so that the top of the head restraint iseven with the top of your head and positioned as close as possible to theba
Using the manual lumbar support (if equipped)The lumbar support control islocated on the inboard side of thedriver’s seatback.Turn the lumbar support
WARNING: To reduce the risk of possible serious injury: Do nothang objects off seat back or stow objects in the seatback mappocket (if equipped) when
Heated seats (if equipped)WARNING: Persons who are unable to feel pain to the skinbecause of advanced age, chronic illness, diabetes, spinal cordinjur
The adjustable head restraintsconsist of :• a trimmed energy absorbing foamand structure (1),• two steel stems (2),• a guide sleeve adjust/removebutto
WARNING: The adjustable head restraint is a safety device.Whenever possible it should be installed and properly adjustedwhen the seat is occupied.To r
Properly adjust the head restraint so that the top of the head restraint iseven with the top of your head and positioned as close as possible to theba
Attach the safety belt web snapbutton to the quarter trim panelsnap button. This will ensure thatsafety belt does not get caught bystaying out of the
Returning the second row seats to upright position1. Pull seatback up and into uprightposition making sure seatback locksinto place and the red seatun
To remove the second row cushion1. Lift the yellow tab to release thehinges.2. Pull the cushion to the outboardside of the vehicle.To install the seco
Question AnswerCan you charge the battery with aplug into an A/C outlet?There are no provisions forcharging the high voltage batteryfrom a power suppl
• Restraint system warning light and back-up tone.• The electrical wiring for the airbags, crash sensor(s), safety beltpretensioners, front safety bel
Front passenger sensing systemFor airbags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occu
Front safety belt pretensionersThe safety belt pretensioners at the front outboard seating positions aredesigned to tighten the safety belts firmly ag
SAFETY BELT SYSTEMWARNING: Always drive and ride with your seatback uprightand the lap belt snug and low across the hips.WARNING: To reduce the risk o
WARNING: Safety belts and seats can become hot in a vehiclethat has been closed up in sunny weather; they could burn asmall child. Check seat covers a
Restraint of pregnant womenWARNING: Always ride and drive with your seatback uprightand the safety belt properly fastened. The lap portion of thesafet
In addition, the retractor is designed to lock if the webbing is pulled outtoo quickly. If this occurs, let the belt retract slightly and pull webbing
WARNING: BELT AND RETRACTOR ASSEMBLY MUST BEREPLACED if the safety belt assembly “automatic lockingretractor” feature or any other safety belt functio
WARNING: Failure to replace the safety belt assembly underthe above conditions could result in severe personal injuries inthe event of a collision.Saf
Belt-Minder姞The Belt-Minder威 feature is a supplemental warning to the safety beltwarning function. This feature provides additional reminders byinterm
Using your vehicle with a snowplowDo not use this vehicle for snowplowing.Your vehicle is not equipped with a snowplowing package.Using your vehicle a
If... Then...The driver’s or frontpassenger’s safety belt becomesunbuckled for approximately1 minute while the vehicle istraveling at least 3 mph(5 km
Reasons given... Consider...⬙Traffic is light⬙ Nearly 1 of 2 deaths occur insingle-vehicle crashes, many whenno other vehicles are around.⬙Belts wrink
The driver and front passenger Belt-Minder威 features can bedeactivated/activated by performing the following procedure:Before following the procedure,
AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right
WARNING: Never place your arm over the airbag module as adeploying airbag can result in serious arm fractures or otherinjuries.To properly position yo
Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear
The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt
impact sensors, the system wiring, the airbag system readiness light, theairbag backup power and the airbag ignitors).WARNING: Several air bag system
The front passenger sensing systemuses a ⬙passenger airbag off⬙ or ⬙passairbag off⬙ indicator which willilluminate and stay lit to remind youthat the
OccupantPass Airbag OffIndicator LampPassenger AirbagEmpty seat Unlit DisabledSmall child in child safety seat orboosterLit DisabledSmall child with s
• How fast the vehicle was travelling; and• Where the driver was positioning the steering wheel.This data can help provide a better understanding of t
If you think that the status of the “passenger airbag off” indicator lamp isincorrect, check for the following:• Objects lodged underneath the seat•Ob
• Driver and/or adult passengers should check for any objects lodgedunderneath the front passenger seat or cargo interfering with the seat.• Remove th
Seat-mounted side airbag systemWARNING: Do not place objects or mount equipment on ornear the airbag cover on the side of the seatbacks of the frontse
How does the side airbag system work?The design and development of theside airbag system includedrecommended testing proceduresthat were developed by
WARNING: Several airbag system components get hot afterinflation. Do not touch them after inflation.WARNING: If the sideairbag has deployed, theairbag
Safety Canopy姞 SystemWARNING: Do not placeobjects or mount equipmenton or near the headliner at thesiderail that may come intocontact with a deploying
How does the Safety Canopy姞 System work?The design and development of theSafety Canopy system includedrecommended testing proceduresthat were develope
The Safety Canopy system is designed to activate when the vehiclesustains lateral deceleration sufficient to cause the RCM to initiate SafetyCanopy in
Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref
SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag suppleme
Additionally, when you connect to Traffic, Directions andInformation (if equipped, U.S. only) the service uses GPStechnology and advanced vehicle sens
Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfants ortoddlersChildren weighing 40 lb
Recommendations for attaching child safety restraints for childrenRestraintTypeChildWeightUse any attachment method as indicatedbelow by “X”LATCH(lowe
WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli
Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle.If the child is the proper height, age, and weigh
Installing child safety seats with combination lap and shoulderbeltsThe rear seat head restraints must be removed when using a childseat that utilizes
1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan
4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear
9. Attach the tether strap (if thechild seat is equipped). Refer toAttaching child safety seats withtether straps later in this chapter.10. Before pla
Your vehicle has LATCH lower anchors for child seat installation at theseating positions marked with the child seat symbol.The LATCH anchors are locat
Use of inboard lower anchors from the outboard seating positions(center seating use)The lower anchors at the center of the second row rear seat are sp
EXPORT UNIQUE (NON–UNITED STATES/CANADA) VEHICLESPECIFIC INFORMATIONFor your particular global region, your vehicle may be equipped withfeatures and o
Attaching child safety seats with tether strapsMany forward-facing child safety seats include a tether strap whichextends from the back of the child s
2. Locate the correct anchor for theselected seating position.There are three tether anchorslocated on the headliner at the rearof the vehicle.3. Clip
Child booster seatsThe belt-positioning booster (booster seat) is used to improve the fit ofthe vehicle safety belt. Children outgrow a typical child
When children should use booster seatsChildren need to use booster seats from the time they outgrow thetoddler seat until they are big enough for the
Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction
Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a
Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi
NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e
VEHICLE CHARACTERISTICS4WD system (if equipped)Your vehicle may be equipped with a four-wheel drive (4WD) system.With the 4WD option, power will be de
• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUVs and
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen
TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary
INFLATING YOUR TIRESSafe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air
When weather temperature changes occur, tire inflation pressures alsochange. A 10°F (6°C) temperature drop can cause a corresponding dropof 1 psi (7 k
TIRE CAREInspecting your tires and wheel valve stemsPeriodically inspect the tire treads for uneven or excessive wear andremove objects such as stones
WARNING: AgeTires degrade over time depending on many factors such asweather, storage conditions, and conditions of use (load, speed,inflation pressur
WARNING: Only use replacement tires and wheels that are thesame size, load index, speed rating and type (such as P-metricversus LT-metric or all-seaso
Note: The use of a different tire can affect the fuel economy of yourvehicle.The tire pressure monitoring sensors mounted in the wheels (originallyins
Tire and wheel alignmentA bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your
Note: If your tires show uneven wear ask an authorized dealer to checkfor and correct any wheel misalignment, tire imbalance or mechanicalproblem invo
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi
3. 65: Indicates the aspect ratio which gives the tire’s ratio of height towidth.4. R: Indicates a “radial” type tire.5. 15: Indicates the wheel or ri
8. U.S. DOT Tire Identification Number (TIN): This begins with theletters “DOT” and indicates that the tire meets all federal standards. Thenext two n
13. Maximum Permissible Inflation Pressure: Indicates the tiremanufacturers’ maximum permissible pressure and/or the pressure atwhich the maximum load
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre
The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw
When your temporary spare tire is installedWhen one of your road tires needs to be replaced with the temporary spare,the TPMS will continue to identif
Low tirepressurewarning lightPossible cause Customer action requiredFlashing warninglightSpare tire in use Repair the damaged road wheel/tireand reins
SNOW TIRES AND CABLESWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. Use of any tire orwheel
VEHICLE LOADING – WITH AND WITHOUT A TRAILERThis section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehic
Seating and Safety Restraints 117Seating 117Personal Safety System™ 129Safety belt system 133Airbags 143Child restraints 159Tires, Wheels and Loading
WARNING LIGHTS AND CHIMESShown in standard measure. Metric similar.Warning lights and gauges can alert you to a vehicle condition that maybecome serio
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
WARNING: Do not use replacement tires with lower loadcarrying capacities than the original tires because they maylower the vehicle’s GVWR and GAWR lim
• A final example for your vehicle with 1,400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the
TRAILER TOWINGTrailer towing with your vehicle may require the use of a trailer towoption package.Trailer towing puts additional loads on your vehicle
Powertrain Maximum GCWR - lb(kg)1Maximum TrailerWeight - lb (kg)22WD 2.5L 4880 (2214) 1000 (454)4WD 2.5L 5040 (2286) 1000 (454)1For high altitude oper
Trailer brakesElectric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspeci
Trailer towing tips• Practice turning, stopping and backing-up before starting on a trip toget the feel of the vehicle-trailer combination. When turni
WARNING: Under engine misfire conditions, excessive exhausttemperatures could damage the catalytic converter, the fuelsystem, interior floor coverings
RECREATIONAL TOWINGFollow these guidelines if you have a need for recreational (RV) towing.An example of recreational towing would be towing your vehi
STARTINGPositions of the ignition1. Off— locks the gearshift leverand allows key removal.2. Accessory— allows the electricalaccessories such as the ra
Important safety precautionsA computer system controls the engine’s idle revolutions per minute(RPM). When the engine starts, the idle RPM runs higher
3. Turn the key to 3 (on) withoutturning the key to 4 (start).Some warning lights will briefly illuminate. See Warning lights andchimes in the Instrum
Note: If the engine fails to start when it should, which is indicated bythe service engine soonlight , put the gearshift lever into P (Park),turn the
Prior to using the engine block heater, follow these recommendations forproper and safe operation:• For your safety, use an outdoor extension cord tha
How to use the engine block heaterEnsure the receptacle terminals are clean and dry prior to use. To cleanthem, use a dry cloth.Depending on the type
Using ABSWhen hard braking is required, apply continuous force on the brakepedal. Do not pump the brake pedal since this will reduce theeffectiveness
When the accelerator pedal is released or the brake pedal is applied, thebrake controller automatically detects the amount of decelerationrequested an
The parking brake is not recommended to stop a moving vehicle.However, if the normal brakes fail, the parking brake can be used to stopyour vehicle in
Safety belt: Reminds you to fastenyour safety belt. A Belt-Minder威chime will also sound to remind youto fasten your safety belt. Refer tothe Seating a
WARNING: Remember that even advanced technology cannotdefy the laws of physics. It’s always possible to lose control of avehicle due to inappropriate
When AdvanceTrac威 with RSC威 performs a normal system self-check,some drivers may notice a slight movement of the brake, and/or arumble, grunting, or g
The engine traction control and brake traction control system may bedeactivated in certain situations. See the Switching off traction controlsection b
Switching off traction controlIf the vehicle is stuck in snow, mud or sand, and seems to lose enginepower, switching off the traction control features
Trailer sway control (if equipped)Your vehicle may be equipped with trailer sway control (TSC). Whenproperly equipped, trailer sway control will use t
STEERINGYour vehicle is equipped with an electric power-assisted steering (EPAS)system. There is no fluid reservoir to check or fill.If your vehicle l
WARNING: Loaded vehicles, with a higher center of gravity,may handle differently than unloaded vehicles. Do not overloadyour vehicle and use extra pre
WARNING: Do not drive your vehicle until you verify that thebrake lamps are working.WARNING: When doing this procedure, you will be taking thevehicle
R (Reverse)With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Re
REVERSE SENSING SYSTEM (IF EQUIPPED)The reverse sensing system (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when R (Reverse
High engine or high motorelectronic coolant temperature:Illuminates when the engine coolantor motor electronics coolant temperature is high. The messa
The RSS detects obstacles up to6 feet (1.8 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the
REARVIEW CAMERA SYSTEM (IF EQUIPPED)The rearview camera system locatedon the liftgate provides a videoimage, which appears in therearview mirror or on
Note: The default setting for the camera delay is off. Press the“Settings” button found on the navigation screen (if equipped) to set thecamera delay
Servicing• If the image comes on while the vehicle is not in R (Reverse), havethe camera inspected by your authorized dealer.• If the image is not cle
For best performance, the driver should drive the vehicle as parallel aspossible while passing a parking space. If driven too fast (above 18 mph[30 km
When you determine the vehicle is back far enough or you hear a solidtone from reverse sensing system, bring the vehicle to a complete stopand move th
• Exceeding a vehicle speed of 6 mph (10 km/h) during automaticsteering• Deactivating the AdvanceTrac威 system or the system has activated ona slippery
Why doesn’t APA position the vehicle where I want in the space?• The driver allows the vehicle to roll in the opposite direction of thetransmission, s
BLIND SPOT MIRRORSBlind spot mirrors have an integrated convex spotter mirror built intothe upper outboard corner of the outside mirrors. They are des
FOUR WHEEL DRIVE (4WD) SYSTEM (IF EQUIPPED)WARNING: For important information regarding safe operationof this type of vehicle, see Preparing to drive
Low fuel: Illuminates when the fuellevel in the fuel tank is at or nearempty (refer to Fuel gauge in thischapter).Speed control: Illuminates whenthe s
If your vehicle goes off the edge of the pavement• If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, an
WARNING: If the parking brake is fully released, but the brakewarning lamp remains illuminated, the brakes may not beworking properly. See your author
Avoid excessive speed because vehicle momentum can work against youand cause the vehicle to become stuck to the point that assistance maybe required f
Driving on hilly or sloping terrainAlthough natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should
Avoid sudden applications of power and quick changes of direction onsnow and ice. Apply the accelerator slowly and steadily when startingfrom a full s
DRIVING THROUGH WATERIf driving through deep or standingwater is unavoidable, proceed veryslowly. Never drive through waterthat is higher than the bot
ROADSIDE ASSISTANCEVehicles sold in the U.S. : Getting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany off
Vehicles sold in the U.S. : Using roadside assistanceComplete the roadside assistance identification card and place it in yourwallet for quick referen
FUEL PUMP/HIGH VOLTAGE SHUT-OFF SWITCHESThe fuel pump shut-off switch stops the electric fuel pump from sendingfuel to the engine and the high voltage
To reset the switch(es):1. Turn the ignition to the off position.2. Check the fuel system for leaks.3. If no leaks are apparent, reset the switch by p
HEV engine off reminder chime: Sounds for 10 seconds when thePRNDL is in the P (Park) position and the Driver’s door is ajar (open)while ignition is o
COLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge10A Red Red — — —15A Blue Blue — — —20A Yellow Yellow Yellow Blue Bl
The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingProtected Circuits1 30A 110V inverter2 15A Brake on/off switch3 15A SYNC威 module4 30A M
Fuse/RelayLocationFuse AmpRatingProtected Circuits15 10A Climate control16 15A Not used (spare)17 20A All lock motor feeds, Liftgaterelease, Liftglass
Fuse/RelayLocationFuse AmpRatingProtected Circuits41 15A Driver/passenger door lockswitches, Auto dimming mirror,Compass, Ambient lighting, Moonroof,
The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingProtected CircuitsA 80A Midi Power steering control moduleB 125A Midi Passenger compart
Fuse/RelayLocationFuse AmpRatingProtected Circuits14 10A* Heater/Coolant pump1550A** Traction battery control module(TBCM)16 40A** Cooling fan 117 40A
Fuse/RelayLocationFuse AmpRatingProtected Circuits31A — Reverse lamp relay31B — Not used31C — Heater pump relay31D — Coolant pump relay31E — Not used3
Auxiliary relay boxThe relay box is located in the engine compartment on the radiatorsupport bracket.Fuse/RelaylocationFuse ampratingDescriptionRelay
CHANGING THE TIRESIf you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel
2. Full-size dissimilar spare with label on wheel: This spare tire hasa label on the wheel that states: “THIS TIRE AND WHEEL FORTEMPORARY USE ONLY”Whe
Battery gauge: Providesinformation about the vehicle’senergy usage.• ASSIST — Battery provides extrapower to boost the vehicle’sacceleration.• CHARGE
• Winter weather driving capability• Wet weather driving capability• All-wheel driving capability (if applicable)• Load leveling adjustment (if applic
To remove jack from vehicle:1. Release the thumbscrew on thebracket.2. Release the retention clip on theupper part of the jack bracket.3. Dislodge the
If equipped with a tether, perform the following additional steps:4. Lift the spare tire on end toaccess tether attachment (1).5. Use the lug wrench t
Tire change procedureWARNING: When one of the front wheels is off the ground, thetransmission alone will not prevent the vehicle from moving orslippin
2. Loosen each wheel lug nutone-half turn counterclockwise butdo not remove them until the wheelis raised off the ground.Before placing the jack under
• RearView shown from forward of reartire. Position the jack directly belowthe stud on the rear trailing arm.3. Position the jack according to theguid
Never use the differentials as ajacking point.WARNING: To lessen therisk of personal injury, donot put any part of your bodyunder the vehicle while ch
Reinstall the jack and tools in the cargo area. To replace the jack in thevehicle,• guide the jack bottom first in thetrim opening and position in the
3. Lay the tire on the ground with the valve stem facing down. If yourvehicle is equipped with aluminum wheels, remove the wheel ornament.4. Slide the
WARNING: When a wheel is installed, always remove anycorrosion, dirt or foreign materials present on the mountingsurfaces of the wheel or the surface
MESSAGE CENTERYour vehicle’s message center is capable of monitoring many vehiclesystems and will alert you to potential vehicle problems and variousc
JUMP STARTING (LOW VOLTAGE [UNDERHOOD] BATTERY ONLY)WARNING: The gases around the battery can explode ifexposed to flames, sparks, or lit cigarettes.
Connecting the jumper cablesNote: In the illustration, the vehicle on the bottom is used to designatethe assisting (boosting) battery.1. Connect the p
Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up
GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehi
In Canada:Mailing addressCustomer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Telephone1-800-565-367
IN CALIFORNIA (U.S. ONLY)California Civil Code Section 1793.2(d) requires that, if a manufactureror its representative is unable to repair a motor veh
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.If a warranty con
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee
AVG MPG (L/100km)Average fuel economy displays your average fuel economy in miles/gallonor liters/100 km.If you calculate your average fuel economy by
If your vehicle must be serviced while you are traveling or living inAsia-Pacific Region, Sub-Saharan Africa, U.S. Virgin Islands, CentralAmerica, the
If you buy your vehicle in North America and then relocate to any of theabove locations, register your vehicle identification number (VIN) andnew addr
REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i
• Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as grained door handles, roofracks, bumpers, sid
• Spray Motorcraft威 Engine Shampoo and Degreaser (ZC-20) on allparts that require cleaning and pressure rinse clean. In Canada, useMotorcraft威 Engine
WINDOWS AND WIPER BLADESThe windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, sub
• Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to a
• If a ring forms on the fabric after spot cleaning, clean the entire areaimmediately (but do not oversaturate) or the ring will set.• Do not use hous
FORD AND LINCOLN CAR CARE PRODUCTSYour Ford or Lincoln authorized dealer has many quality productsavailable to clean your vehicle and protect its fini
System check and vehicle feature customizationPress the SETUP button repeatedlyto cycle the message center throughthe following features:PRESS RESET F
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
The following are specific locations in the rear cargo area that consist ofhigh voltage components and/or wiring.1. High voltage connector shield2. Se
Working with the engine off1. Set the parking brake and ensure the gearshift is securely latched in P(Park).2. Turn off the engine and remove the key.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT1. Engine coolant reservoir2. Motor/Electronics (M/E) coolant reservoir3. Engine oil filler cap4. Brak
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
CHANGING THE WIPER BLADES1. Pull the wiper blade and armaway from the glass.2. Squeeze the locking tabs torelease the blade from the arm andpull the b
Changing rear window wiper bladeThe rear wiper arm is designed without a service position. This reducesthe risk of damage to the blade in an automatic
4. Open the hood. Protect yourself from engine heat.5. Locate and carefully remove the engine oil level dipstick.6. Wipe the dipstick clean. Insert th
4. Install the dipstick and ensure it is fully seated.5. Fully install the engine oil filler cap by turning the filler cap clockwise1/4 of a turn unti
Ford production and Motorcraft威 replacement oil filters are designed foradded engine protection and long life. If a replacement oil filter is usedthat
Cleaning 283Maintenance and Specifications 290Engine compartment 293Engine oil 296Battery 299Engine Coolant and Motor/Electronics Coolant 301Fuel info
3. Once “OIL LIFE SET TO XXX%” is displayed, release and press theRESET button to change the Oil Life Start Value. Each release and presswill reduce t
WARNING: When lifting a plastic-cased battery, excessivepressure on the end walls could cause acid to flow through thevent caps, resulting in personal
If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the battery isreco
Checking engine coolantThe concentration and level ofengine coolant should be checked atthe intervals listed in scheduledmaintenance information. Thec
Checking motor/electronics (M/E) coolantThe M/E coolant reservoir is locatedbehind the engine coolant reservoir.Refer to the following enginecoolant s
If the engine coolant has not been checked at the recommended interval,the engine coolant reservoir may become low or empty. If the reservoir islow or
• Do not use alcohol, methanol, brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcoholand other liquids can cause en
Whenever coolant has been added, the coolant level in the coolantreservoir should be checked the next few times you drive the vehicle. Ifnecessary, ad
If you drive in extremely hot climates:• It is still necessary to maintain the coolant concentrationabove 40%.• NEVER decrease the coolant concentrati
Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforerefueling your vehicle.• Al
RefuelingWARNING: Fuel vapor burns violently and a fuel fire can causesevere injuries. To help avoid injuries to you and others:• Read and follow all
Waiting four seconds or pressing the RESET button cycles the messagecenter through each of the language choices.Press and hold the RESET button for tw
4. After you are done pumping fuel, slowly remove the fuel fillernozzle—allow about five seconds after pumping fuel before removing thefuel filler noz
Octane recommendations“Regular” unleaded gasoline with apump (R+M)/2 octane rating of 87 isrecommended. Some stations offerfuels posted as “Regular” w
Running out of fuelAvoid running out of fuel because this situation may have an adverseeffect on powertrain components.If you have run out of fuel:• Y
When filling the vehicle’s fuel tank from a portable fuel container, use thefunnel included with the vehicle.1. Locate the white plastic funnel. Itis
Filling the tankWhen the fuel gauge indicates empty, there is still a small reserve of fuelin the fuel system. When refueling your vehicle after the f
Driving style — good driving and fuel economy habitsSince it is able to operate in electric mode and to collect braking energy,your hybrid vehicle may
Conditions• Heavily loading a vehicle or towing a trailer may reduce fuel economyat any speed.• Carrying unnecessary weight may reduce fuel economy (a
Illumination of the service engine soon indicator, charging systemwarning light or the temperature warning light, fluid leaks, strange odors,smoke or
These temporary malfunctions can be corrected by filling the fuel tankwith good quality fuel, properly closing the fuel fill inlet or letting theelect
Allow the vehicle to sit for at least eight hours without starting theengine. Then, start the engine and complete the above driving cycle. Theengine m
HIGH ENGINE TEMPERATURE — Displayed when the enginecoolant is overheating. Engine coolant temperature warning lamp willilluminate indicating coolant t
AIR FILTERRefer to scheduled maintenance information for the appropriateintervals for changing the air filter element.When changing the air filter ele
VEHICLE STORAGEIf you plan on storing your vehicle for an extended period of time(30 days or more), refer to the following maintenance recommendations
Fuel system• Fill the fuel tank with high-quality fuel until the first automatic shutoffof the fuel pump nozzle.Note: During extended periods of vehic
MOTORCRAFT PART NUMBERSComponent 2.5L I4 engineOil filter FL-910SSpark plugs1Engine air filter element FA-1772Low voltage (underhood)batteryBXT-96R-50
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord Part Name orequivalentFord Part Number / FordSpecificationBrake fluidBetween MINand
Item CapacityFord Part Name orequivalentFord Part Number / FordSpecificationEngine oil 5.3 quarts (5.0L)•Motorcraft威 SAE5W-20 PremiumSynthetic Blend M
Item CapacityFord Part Name orequivalentFord Part Number / FordSpecificationWindshield washerfluidFill as requiredMotorcraft威 PremiumWindshield Washer
ENGINE DATAEngine 2.5L I4 engineCubic inches 152Required fuel Minimum 87 octaneFiring order 1-3-4-2Ignition system Coil on plugSpark plug gap 0.049–0.
IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli
The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating
LOW TIRE PRESSURE — Displayed when one or more tires on yourvehicle have low tire pressure. Refer to Inflating your tires in the Tires,Wheels and Load
FORD CUSTOM ACCESSORIES FOR YOUR VEHICLEA wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of C
*Ford Licensed Accessories (FLA) are warranted by the accessorymanufacturer’s warranty. Ford Licensed Accessories are fully designedand developed by t
FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY)More than 30 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the
Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With
Ford Extended Service Plan3342012 Escape Hybrid (ehv)Owners Guide, 1st PrintingUSA (fus)
FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY)You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is
GENERAL MAINTENANCE INFORMATIONWhy maintain your vehicle?This guide describes the scheduled maintenance required for yourvehicle. Carefully following
Your vehicle is very sophisticated and built with multiple complexperformance systems. Every manufacturer develops these systems usingdifferent specif
Genuine Ford parts and serviceWhen planning your maintenance services, consider your dealership forall your vehicle’s needs.There are a lot of reasons
Owner checks and servicesCertain basic maintenance checks and inspections should be performedby the owner or a service technician at the intervals ind
TOP SPEED MYKEY SETTING — Displayed when a MyKey威 is in useand the MyKey speed limit is on and the vehicle speed is 80 mph(130 km/h). Refer to MyKey威
Multi-point inspectionIn order to keep your vehicle running right, it is important to have thesystems on your vehicle checked regularly. This can help
Scheduled Maintenance3412012 Escape Hybrid (ehv)Owners Guide, 1st PrintingUSA (fus)
NORMAL SCHEDULED MAINTENANCE AND LOGYour vehicle is equipped with a oil minder system that indicates whenthe engine oil should be changed under normal
Additional maintenance items1Miles (x 1,000) 20 30 40 60 80 90 100 120 140 150Kilometers (x 1,000) 32 48 64 96 128 144 160 192 225 240Replace cabin ai
Maintenance schedule logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDAT
DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO
DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO
SPECIAL OPERATING CONDITIONSIf you operate your vehicle primarily in any of the following conditions,you need to perform additional maintenance as ind
Operating in dusty conditions such as unpaved or dusty roadsInspect frequently,service as requiredReplace cabin air filter (if equipped)Replace engine
Special operating condition logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER
SPACE FOUND STOP (if equipped) — May display when using theactive park assist system. See Active park assist in the Driving chapterfor more informatio
DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO
EXCEPTIONSThere are several exceptions to the Normal Schedule. They are listed below:Normal vehicle axle maintenance: Rear axles and power take-off(PT
Edge/MKX AWD only – vehicles operating off-road in sand during highambient temperatures must replace the AWD PTU (All-wheel drivePower Transfer Unit)
AAccessory delay ...79Active Park Assist ...233AdvanceTrac ...219Airbag supplement
in front seat ...164in rear seat ...164LATCH ...167recommendatio
specifications ...324Event data recording ...14Exhaust fumes ...214FFleet MyKey programmi
KKeyless entry systemautolock ...103, 105keypad ...111locking and unlocking doors ..113progr
Power distribution box(see Fuses) ...253Power door locks ...103Power mirrors ...
Starting your vehicle ...211–213jump starting ...270Steering wheelcontrols ...83tilting
AUDIO SYSTEMSAM/FM/single CD/MP3 satellite compatible sound systemWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and
AM/FM Radio/ VOL (Power/Volume): Pressto turn the radio on/off. Turn theknob to increase/decrease volume.If the volume is set above a certainlevel and
To activate the autoset feature: Press MENU repeatedly until AUTOPRESET ON/OFF appears in the display. Use SEEK/TRACK toturn AUTO PRESET to ON, and ei
EJECT: Press EJECT to eject the CD./ Play/Pause: Press toplay/pause a track when playing aCD.SEEK/TRACK: PressSEEK/TRACK to access theprevious/next tr
CONGRATULATIONSCongratulations on acquiring your new Ford Hybrid. Please take the timeto get well acquainted with your vehicle by reading this handboo
COMPRESSION: Press MENU repeatedly until COMPRESSION ON/OFFappears in the display. Use SEEK/TRACK to switch between ONand OFF. When COMPRESSION is ON,
SCAN: Press SCAN for a brief sampling of all available SIRIUS satellitechannels. If a specific category is selected, (Jazz, Rock, News, etc.) pressSCA
• SONG SEEK MENU- Press OK to enter song seek menu.Press / to scroll through the following options:a. SAVE THIS SONG?: Press OK to save the currently
• CHANNEL LOCKOUT MENU- Press OK to enter the ChannelLockout menu. Press the/ to scroll through the followingoptions:a. LOCK/UNLOCK THIS CHANNEL: Pres
• SPEED COMPENSATED VOLUME (if equipped): Allows the radiovolume to automatically adjust with vehicle speed to compensate forroad and wind noise. Use
Auxiliary input jack (Line in)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends th
3. Attach one end of the audio extension cable to the headphone outputof your player and the other end of the audio extension cable to the AIJin your
USB port (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdriver
Radio reception factors:There are three factors that can affect radio reception:• Distance/strength: The further you travel from an FM station, thewea
Do not use any irregular shapedCDs or discs with a scratchprotection film attached.CDs with homemade paper(adhesive) labels should not beinserted into
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou
• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w
Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m
Radio Display Condition Action RequiredNO TEXT Category informationnot available.Category informationnot available at thistime on this channel.The sys
DUAL AUTOMATIC TEMPERATURE CONTROL1. AUTO/Driver temperature: Press to engage full automaticoperation. The system will automatically determine fan spe
5. Power/ : Press to activate/deactivate the climate controlsystem. When the system is off, outside air is shut out. Press +or– to manually increase/d
11. Recirculated air: Press to activate/deactivate air recirculationin the vehicle. Recirculated air may reduce the amount of time needed tocool down
• To improve the A/C cool down, drive with the windows slightly openfor 2-3 minutes after start up or until the vehicle has been “aired out.”• A small
REAR WINDOW DEFROSTERRThe rear defroster control is located on the climate control panel andworks to clear the rear window of fog and thin ice.The veh
HEADLAMP CONTROLRotate the headlamp control to thefirst positionto turn on theparking lamps.Rotate to the second positiontoturn on the headlamps.Rotat
PERCHLORATE MATERIALCertain components of this vehicle such as airbag modules, seat beltpretensioners, and button cell batteries may contain Perchlora
3. Rotate the headlamp control to the off position.4. Turn the vehicle on.5. Turn the vehicle off.6. Turn the headlamp control to the autolamp positio
Daytime running lamps (DRL) (if equipped)Turns the low beam headlamps on with a reduced output.To activate:• the ignition must be in the on position.•
AIMING THE HEADLAMPSThe headlamps on your vehicle are properly aimed at the assembly plant.If your vehicle has been in an accident, the alignment of y
5. Locate the vertical adjuster onthe headlamp, then usea4mmsocket to turn the adjuster eithercounterclockwise (to adjust up) orclockwise (to adjust d
Map lamps (without moon roof)The map lamp controls (withoutmoon roof) are located on the domelamp.• Press the button on either side ofeach map lamp to
Ambient lighting (if equipped)Illuminates footwells, cupholders,the console bin and the console traywith a choice of several colors. Theambient lighti
Take your vehicle to a dealer for service if any of the above conditions ofunacceptable moisture are present.Using the right bulbsReplacement bulbs ar
Replacing headlamp bulbs1. Make sure that the headlamp control is in the off position.2. Open the hood.3. Reach over the front bolster.4. Remove the b
5. Carefully pull the bulb out of thesocket and push in the new bulb.6. Install the bulb socket into thelamp assembly and rotate clockwise.Replacing f
Replacing license plate lamp bulbs1. Make sure the headlamp switch isin the off position.2. Depress the lever and carefullypry the license plate lamp
Driving: The gas engine automatically starts and stops to provide powerwhen it’s needed and to save fuel when it’s not. While coasting at lowspeeds, c
3. Pull the bulb straight out of thesocket and push in the new bulb.To complete installation, follow theremoval procedure in reverse order.Replacing f
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
Rear window wiper/washer controlsFor rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select:2 — Normal spe
ILLUMINATED VISOR MIRRORLift the mirror cover to turn on thevisor mirror lamp.Slide-on-rod featureRotate the visor towards the sidewindow and extend i
Compass zone adjustment1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Turn ignition to the on p
2. To calibrate, press and hold theRESET control for approximatelyten seconds until CAL appears.Release the control.3. Slowly drive the vehicle in aci
The tray and inside bin can beremoved to open up space to fit alaptop computer, MP3 players, CDsor handbags. To remove, open theconsole lid and pull t
To prevent the fuse from being blown, do not use the power point(s)over the vehicle capacity of 12V DC/180W. If the power point or cigarlighter socket
Do not keep electrical devices plugged in the power point wheneverthe device is not in use. It is not recommended to use anyextension cord with the 11
One-touch downAllows the driver’s window to open fully without holding the controldown. Press the switch completely down to the second detent andrelea
Unique Hybrid operating characteristicsYour Hybrid, with its new technology, behaves differently compared to anon-hybrid. Here is a description of the
Note: A rear center passenger and/or raised rear center headrest (ifequipped) may also block the light from reaching the sensor.Do not clean the housi
Heated outside mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated.Do not re
3. Press and release SET +.4. Take your foot off the accelerator pedal.5. The indicatorlight on the instrument cluster will turn on.Note:• Vehicle spe
Turning off speed controlTo turn off the speed control, press OFF or turn off the ignition.Note: When you turn off the speed control or the ignition,
SYNC威 system hands-freecontrol feature (if equipped)Press briefly to use the voicecommand feature. You will hear atone and LISTENING will appear inthe
To open the moon roof: The moonroof is equipped with an automatic,one-touch, opening, closing andventing feature. Press and releasethe rear portion of
The moon roof has a sliding shade that can be opened or closed when theglass panel is shut. To close the shade, pull it toward the front of the vehicl
Additional Car2U威 system information can be found on-line atwww.learcar2U.com or by calling the toll-free Car2U威 system help line at1-866-572-2728.Typ
Make sure that your key is on and engine off while programming thetransmitter.1. Firmly press the two outerCar2U威 system buttons for1–2 seconds, then
The indicator light above the selected button will turn on to confirm thatthe Car2U威 system is responding to the button command.To program another rol
Driving to optimize fuel economyYour fuel economy should improve throughout your hybrid’s break-inperiod. As with any vehicle, fuel economy can be sig
3. To input these positions into theCar2U威 system, simultaneouslypress all three Car2U威 systembuttons for a few seconds and thenrelease to put the dev
Erasing the Car2U姞 Home Automation System buttonsNote: The system allows for three devices to be programmed. If youneed to change or replace any of th
POSITIVE RETENTION FLOOR MATWARNING: Always usefloor mats that are designedto fit the foot well of your vehicle.Only use floor mats that leave thepeda
LIFTGATE• To open the liftgate window,unlock the liftgate (with thepower door locks or the remoteentry) and press the right sidecontrol button located
CARGO AREA FEATURESCargo shade (if equipped)If your vehicle has a cargo shade, you can use it to cover items in thecargo area of your vehicle.To insta
WARNING: When loading the roof rail crossbars, it isrecommended to evenly distribute the load, as well as maintain alow center of gravity. Loaded vehi
3. Use a long, flat object to depressthe tongue in the endcaps on bothsides of the cross-bar.4. Slide the cross-bar assembly offthe end of the rail.Be
KEYSYour vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and unl
MYKEY姞The MyKey威 feature allows you to program a restricted driving mode topromote good driving habits. All but one of the keys programmed to thevehic
2. Press and release the RESET button. HOLD RESET TO CONFIRMMYKEY will be displayed.3. Press and hold the RESET button for two seconds until MARK THIS
Comments to this Manuals