Ford 2004 Thunderbird v.2 User Manual

Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 14Entertainment Systems 16AM/FM stereo with in-dash six CD 16Climate Controls 2

WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa

SAFETY SEATS FOR CHILDRENChild and infant or child safety seatsUse a safety seat that is recommended for the size and weight of thechild. Carefully fo

Carefully follow all of the manufacturer’s instructions includedwith the safety seat you put in your vehicle. If you do not installand use the safety

2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt isextracted and a c

Attaching child safety seats with tether strapsMost new forward-facing child safety seats include a tether strap whichgoes over the back of the seat a

3. Route the child safety seat tetherstrap under the head restraint andover the back of the seat.4. Grasp the tether strap andposition it to the seat

6. Clip the tether strap to theanchor on the seat frame.7. Rotate the tether strap clip.8. Tighten the child safety seattether strap according to them

This type of child seat eliminates the need to use safety belts to attachthe child seat. For forward-facing child seats, the tether strap must alsobe

STARTINGPositions of the ignition1. LOCK, locks the gearshift leverand allows key removal. (Thesteering wheel will not lock afterkey removal.)2. OFF,

Extended idling at high engine speeds can produce very hightemperatures in the engine and exhaust system, creating the riskof fire or other damage.Do

Brake system warning light: Toconfirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the ON

• Turn the key to 4 (ON) withoutturning the key to 5 (START).Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to i

strongly recommended if you live in a region where temperatures reach-23° C (-10° F) or below. For best results, plug the heater in at leastthree hour

ABS warning lampThe ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringsta

TRACTION CONTROL姟Your vehicle is equipped with a Traction Control娂 system. This systemhelps you maintain the stability and steerability of your vehicl

STEERINGTo prevent damage to the power steering system:• Never hold the steering wheel at its furthest turning points (until itstops) for more than a

When the key is in the ignition and in the OFF position, theautomatic transmission shift lever can be moved from the P(Park) position without the brak

Driving with a 5–speed automatic transmissionThis vehicle is equipped with an adaptive Transmission Shift Strategy.Adaptive Shift strategy offers the

R (Reverse)With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Re

• Selecting 2 (Second) at higher speeds will cause the transmission todownshift to second gear at the appropriate vehicle speed.1 (First)This position

Manual shift modeWith the gearshift lever in D5(Overdrive), the gearshift lever canbe moved to the right and into themanual shift mode. The transmissi

Engine oil pressure: Illuminateswhen the oil pressure falls below thenormal range, refer to Engine oil inthe Maintenance andspecifications chapter.Eng

• If shifter (-) is tapped more than once in rapid succession, thetransmission will downshift only into the next lower gear, then whenthe vehicle reac

VEHICLE LOADING – WITH AND WITHOUT A TRAILERThis section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehic

Exceeding the Safety Certification Label axle weight rating limitscould result in substandard vehicle handling, performance,engine, transmission and/o

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

Exceeding any vehicle weight rating limitation could result inserious damage to the vehicle and/or personal injury.TRAILER TOWINGYour vehicle is not e

GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program

Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will

This switch is located in the driver’sfootwell, behind the kick panel.To reset the switch:1. Turn the ignition OFF.2. Check the fuel system for leaks.

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey ———3A Violet Vio

The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 5A Starter relay coil2 5A Radio start sign

Low washer fluid: Illuminateswhen the windshield washer fluid islow.Bulb warning: A text messageindicates when one of the exteriorfront turn lamps or

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description8 5A Right-hand turn/park lamp andside marker9 15A Right-hand headlamp10 5A

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description34 5A Outside mirrors35 5A Brake pedal switchRelay 1 — Not usedFront power

The high-current fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription1 10A* A/C clutch2 — Not used3 10A* Park

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription13 — Not used14 30A** ABS module power15 — Not used16 30A** Blower motor17 — Not used

Rear power distribution boxThe rear power distribution box islocated in the luggage compartmentunder the spare tire well cover. Thepower distribution

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription1 15A* Rear Electronics Module (REM)2 5A* License plate lamp and rear sidemarkers3 10

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription29 30A** Rear defroster30 — Not used31 40A** Convertible top motor32 30A** SSP2Relay

• Tow a trailer• Use snow chains on the end of the vehicle with the T-type/mini sparetire• Use more than one T-type/mini spare tire at a time• Use com

The usage of a dissimilar spare tire/wheel can lead to impairment of thefollowing:• Handling, stability and braking performance• Comfort and noise• Gr

3. Lift the trunk cargo cover andremove the spare tire, jack and toolbag with lug wrench.4. Loosen each wheel lug nutone-half turn counterclockwise bu

GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera

5. Put the jack in the jack notchnext to the tire you are changing.Turn the jack handle clockwise untilthe wheel is completely off theground.Never use

9. Remove the jack and fully tightenthe lug nuts in the order shown.Note: The jack cannot beproperly stowed when a full sizetire is placed here. Secur

Wheel lug nut torque specificationsRetighten the lug nuts to the specified torque at 800 km (500 miles)after any wheel disturbance (tire rotation, cha

1. Use only a 12–volt supply to start your vehicle.2. Do not disconnect the battery of your disabled vehicle as this coulddamage the vehicle’s electri

2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat

4. Make the final connection of the negative (-) cable to the spare tiretie-down stud. (Your vehicle may be equipped with a plastic cap on topof the t

Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the spare tire tie-dow

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli

Trip odometer: Registers thekilometers (miles) of individualjourneys. To reset, depress theRESET control. To switch thedisplay from Trip A to the Trip

Ford Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf you own a Lincoln vehicle and are away f

In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or

The Dispute Settlement Board may not be available in all states. FordMotor Company reserves the right to change eligibility limitations, modifyprocedu

from Ford and Lincoln Mercury dealership management, recognized fortheir business leadership qualities.What the Board needsTo have your case reviewed

Making a decisionBoard members review all available information related to eachcomplaint, including oral presentations, and arrive at a fair and impar

In the CAMVAP program, impartial third-party arbitrators conducthearings at mutually convenient times and places in an informalenvironment. These impa

ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro

3. The vehicle is out of service for repair of nonconformities for a total ofmore than 30 calendar days (not necessarily all at one time)In the case o

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is

PAINT CHIPSYour dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam

AUDIOPHILE SATELLITE READY AM/FM STEREO IN-DASH SIX CDRADIO1. Seek: Press and releaseSEEK/ for previous/nextstrong station, selection or track.2. Rewi

• Cover the highlighted areas to prevent water damage when cleaningthe engine.• Never wash or rinse the engine while it is running; water in therunnin

• Do not use fuel, kerosene, or paint thinner to clean any parts.• Wiper blades can be cleaned with isopropyl (rubbing) alcohol orwindshield washer so

INTERIORFor fabric, carpets, cloth seats, safety belts and seats equipped with sideair bags:• Remove dust and loose dirt with a vacuum cleaner.• Remov

FORD, LINCOLN AND MERCURY CAR CARE PRODUCTSYour Ford, Lincoln or Mercury dealer has many quality products availableto clean your vehicle and protect i

SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a

Working with the engine off1. Set the parking brake and ensure the gearshift is securely latched in P(Park).2. Turn off the engine and remove the key.

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.9L–4V V8 engine1. Engine oil filler cap2. Engine oil dipstick3. Brake fluid reservoir4. Engine coola

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

5. Locate and carefully remove theengine oil level indicator (dipstick).6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.•

3. Recheck the engine oil level. Make sure the oil level is not above theMAX mark on the engine oil level indicator (dipstick).4. Install the indicato

4. Mute: Press to MUTE playingmedia; press again to return toplaying media5. Eject: Press to eject a CD. Pressand hold to eject all loaded discs.6. Ba

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich is located in the luggagecompartment, next to the spare tire.Your batte

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyeswhen working near

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “cold fill level” or within the “c

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn youbadly. Also, you can be bur

coolant pressure relief cap on the radiator of a vehicle with an overflowsystem, follow these steps to add engine coolant.To reduce the risk of person

Used engine coolant should be disposed of in an appropriatemanner. Follow your community’s regulations and standards for recyclingand disposing of aut

If the engine reaches a preset over-temperature condition, the enginewill automatically switch to alternating cylinder operation. Each disabledcylinde

The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, wait until it stopsbefore completely rem

clothing and wash skin thoroughly with soap and water. Repeated orprolonged skin contact with fuel liquid or vapor causes skin irritation.• Be particu

FIND Program type: Allows you to search RDS-equipped stations for acertain category of music format: Classic, Country, Info, Jazz, Oldies,R&B, Rel

5. Turn the filler cap clockwise 1/8 of a turn until it stops.If the “Check Fuel Cap” indicator comes on and stays on after you startthe engine, the f

with the recommended octane rating, see your dealer or a qualifiedservice technician to prevent any engine damage.Fuel qualityIf you are experiencing

ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform

2. Each time you fill the tank, record the amount of fuel added (in litersor gallons).3. After at least three to five tank fill-ups, fill the fuel tan

• Warming up a vehicle on cold mornings is not required and mayreduce fuel economy.• Resting your foot on the brake pedal while driving may reduce fue

It is important to note the box in the lower left corner of the windowsticker. These numbers represent the Range of L/100 km (MPG)expected on the vehi

permitted to intentionally remove an emission control device or preventit from working. Information about your vehicle’s emission system is onthe Vehi

If the vehicle’s powertrain system or its battery has just been serviced,the on-board diagnostics system is reset to a “not ready for I/M test”conditi

BRAKE FLUID RESERVOIRThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the

Changing the air filter element1. Loosen the hose clamp on theoutlet tube at the air filter housing.2. Release the two clamps thatsecure the cover to

13. Power/volume: Press to turnON/OFF; turn to increase ordecrease volume levels.Speed sensitive volume: Radiovolume changes automatically andslightly

5. Install a new air filter element. Be careful not to crimp the filterelement edges between the air filter housing and cover. This could causefilter

Tire Quality Grades apply to new pneumatic tires for use on passengercars. They do not apply to deep tread, winter-type snow tires,space-saver or temp

The temperature grade for this tire is established for a tire thatis properly inflated and not overloaded. Excessive speed,underinflation, or excessiv

INFORMATION CONTAINED ON THE TIRE SIDEWALLFederal law requires tire manufacturers to place standardizedinformation on the sidewall of all tires. This

7. H: Indicates the tire’s speed rating. The speed rating denotes thespeed at which a tire is designed to be driven for extended periods oftime under

10. Tire Ply Composition and Material Used: Indicates the number ofplies or the number of layers of rubber-coated fabric in the tire tread andsidewall

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation than those of “P” typetires; t

Information on “T” type tiresT145/80D16 is an example of a tiresize.Note: The temporary tire size foryour vehicle may be different thanthis example.1.

Use the recommended cold inflation pressure for optimum tireperformance and wear. Under-inflation or over-inflation may causeuneven treadwear patterns

6. Visually inspect the tires to make sure there are no nails or otherobjects embedded that could poke a hole in the tire and cause an airleak.7. Chec

Seating and Safety Restraints 73Seating 73Safety restraints 76Air bags 86Child restraints 96Driving 108Starting 108Brakes 111Traction control/AdvanceT

For information regarding SIRIUS Satellite Radio, please call toll-free888-539-SIRIUS (888-539-7474) or visit the SIRIUS website atwww.siriusradio.com

• Front Wheel Drive (FWD)vehicles (front tires at top ofdiagram)• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive (4WD)vehicles (front tires at top of

Sometimes irregular tire wear can be corrected by rotating the tires.Note: If your tires show uneven wear ask a qualified technician at aFord or Linco

• Severe abrasion on the sidewallIf your vehicle has a leak in the exhaust system, a road tire or the sparetire may be exposed to hot exhaust temperat

Tire explosions can cause death, personal injury or propertydamage. Do not allow anyone to stand near, directly ahead orbehind the spinning tire.Never

MOTORCRAFT PART NUMBERSComponent 3.9L-4V V8 engineAir filter element FA-1679Fuel filter FG-1011Battery BXT-66-650Oil filter FL-218PCV valve1Spark plug

REFILL CAPACITIESFluid Ford PartNameApplication CapacityBrake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluid1All Fill to MAX lineon res

Fluid Ford PartNameApplication CapacityWindshieldwasher fluidMotorcraftPremiumWindshieldWasherConcentrateAll Fill to line onreservoir1Use only brake f

LUBRICANT SPECIFICATIONSItem Ford partnameFord partnumberFordspecificationBrake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluid1PM-1 ESA

Item Ford partnameFord partnumberFordspecificationRear AxleLubricantMotorcraft SAE75W-90 FuelEfficient HighPerformanceSynthetic RearAxle Lubricant2XY-

VEHICLE DIMENSIONSVehicle dimensions mm (in)(1) Overall length 4732mm (186.3 in)(2) Overall width 1829mm (72.0 in)(3) Overall height 1323 mm (52.1 in)

CD units are designed to play commercially pressed 12 cm (4.75in) audio compact discs only. Due to technical incompatibility,certain recordable and re

IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt

Vehicle identification number (VIN)The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Plea

Transmission/Transaxle code designationsYou can find a transmission/transaxle code on the vehicle certificationlabel which is located on the door pill

Passenger car application:Code Transmission/Transaxle DescriptionFront wheel drive manual transaxleR5–speed overdrive (MTX75)W5–speed overdrive (M5)Fr

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford

Interior trim kitsLeather wrapped steering wheelsScuff platesSpeed controlLifestyleBike racksCargo organization and managementEngine block heaters and

AAccessory delay ...40Air bag supplemental restraintsystem ...86, 94and child safety seats ...

interior trim ...161plastic parts ...160washing ...158waxing ...

filter, specifications ...169, 204recommendations ...169refill capacities ...205specifications ...

KKeyless entry systemautolock ...68Keyspositions of the ignition ...108LLampsautolamp system ...

DUAL ELECTRONIC AUTOMATIC TEMPERATURE CONTROL(DEATC) SYSTEM1. A/C control: Press to turn onand manually control the airconditioning. Press again todis

Safety Canopy ...94Safety defects, reporting ...157Safety restraints ...76–80belt minder ...

Water, Driving through ...120Windowspower ...40Windshield washer fluid andwipers ...

222

223

224

5. DUAL zone selector: Press totoggle the system between singlezone and dual zone control.6.(Defrost): Distributes outside air through the windshieldd

16. EXT control: Press to displaythe outside air temperature. Pressagain to return to interiortemperature. Exterior readings are most accurate when th

• Do not place items over theclimate temperature sensor grid.This may cause improperoperation of the system.To aid in side window defogging/demisting

CABIN AIR FILTERYour vehicle is equipped with a Cabin air filter. The particulate airfiltration system is designed to reduce the concentration of airb

MASTER LIGHTING SWITCHTurns the lamps off.Turns on the parkinglamps, instrument panel lamps,license plate lamps and tail lamps.Turns the headlamps on.

Always remember to turn on your headlamps at dusk or duringinclement weather. The Daytime Running Light (DRL) Systemdoes not activate your tail lamps

HEADLAMP VERTICAL AIM ADJUSTMENT1. Park the vehicle on a level surface approximately 7.6 meters (25 feet)from a vertical wall or screen directly in fr

Maintenance and Specifications 164Engine compartment 166Engine oil 167Battery 170Fuel information 177Air filter(s) 189Tire Information 192Part numbers

TURN SIGNAL CONTROL• Push down to activate the leftturn signal.• Push up to activate the right turnsignal.INTERIOR LAMPSReading and dome lampsThe read

Function Trade numberPark/turn lamps (front) 3457 AK (amber)Supplemental parking lamps (ifequipped)912Front side marker lamps 194Rear side marker lamp

Replacing headlamp bulbsTo remove the headlamp bulb:1. Make sure headlamp switch is inOFF position, then open the hood.2. Pry up the two retainer pins

6. Without turning, remove the oldbulb from the lamp assembly bypulling it straight out of the lampassembly.To install the new bulb:Handle a halogen h

Replacing front parking lamp/turn signal bulbs1. Make sure headlamp switch is inOFF position, then open the hood.2. Pry up the two retainer pins torel

Replacing front/rear side marker bulbs1. Make sure the headlamp switch isin the OFF position and thenremove the screw and carefully pullthe lamp assem

Prior to pulling the carpet away, instep 1, the trunk trim scuff platemust be removed. This can beaccomplished by pulling gently onthe component until

Replacing license plate lamp bulbs1. Make sure the headlamp switch isin the OFF position and thenremove two screws and the licenseplate lamp assembly

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

POWER TILT/TELESCOPE STEERING COLUMNThe steering column can beadjusted manually by moving thefour-way rocker adjustment controllocated below the turn

CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth

POWER WINDOWSWhen closing the powerwindows, you should verifythey are free of obstructions andensure that children and/or petsare not in the proximity

closed. To re-calibrate the window, press the up switch to raise thewindow until it completes its travel and hold the switch down for 2seconds. Anothe

In the event of battery failure, youcan open the trunk by using yourmaster key on the key cylinderlocated behind the driver’s seat.SPEED CONTROLWith s

3. Press the SET + control andrelease it.4. Take your foot off the acceleratorpedal.5. The indicatorlight on theinstrument cluster will turn on.Note:•

Increasing speed while using speed controlThere are two ways to set a higherspeed:• Press and hold the SET + controluntil you get to the desiredspeed,

Turning off speed controlThere are two ways to turn off the speed control:• Depress the brake pedal or pressCANCEL. This will not erase yourvehicle’s

In any mode:• Press VOL + or − to adjustvolume.Press the PHONE/MUTE control tomute the playing media. Press againto return to the playing media.HOMELI

purchase). It is also suggested that upon the sale of the vehicle, theprogrammed Homelink威 buttons be erased for security purposes, refer toProgrammin

and released. Note: To program the remaining two HomeLink威 buttons,begin with step 2 in the “Programming” section — do not repeat step 1.Note: If the

• Proceed with step 4 in the “Programming” section.Operating the HomeLink姞 Wireless Control SystemTo operate, simply press and releasethe appropriate

SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury and prevent possibledamage to others, you

Lowering the convertible topThe convertible top can be lowered with the side windows either up ordown.Do not lower the top when the top material is we

1. Fasten the snaps on the boot tothe quarter trim panel on both sidesof the vehicle and at the center.2. Tuck the boot under the upperback panel at t

3. Push the two screws down intothe windscreen panel of yourvehicle.4. Push the convertible topswitch, holding it until the topunfolds and moves forwa

8. To fasten both clamps securely,push the clamp handles into theheader on the top until they areflush with the header. Pulling downon the header at t

Also, high pressure car washes may cause water to enter the convertibletop well, which may result in the convertible top staining if the top is notall

Once per year, apply a small amountof silicone lubricant,F5AZ–19553–AA, to the receivers asshown. The lubricant should besprayed directly into the hol

6. Partially turn, 1/2 turn forward,the levers of the top (located in therear on the left and right-hand sideof the vehicle).7. Using the mounting key

Removing the topIt is recommended that you prepare the storage rack before removingthe top. See Removable top storage rack in this section.1. Take the

Removable top storage rackIt is recommended that you prepare the storage rack prior to removingthe top from the vehicle.1. Remove the storage rack fro

8. Place the removable top on thestorage rack.9. Make sure the rear edge of theremovable top rests on the rubberbumpers of the rack legs. Thisprevents

SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and

CELL PHONE USEThe use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,dri

KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w

The inside lights will not turn off if:• they have been turned on using the dimmer control or• any door is open.The battery saver feature will turn of

Keep vehicle doors andluggage compartmentlocked and keep keys and remotetransmitters out of a child’s reach.Unsupervised children could lockthemselves

The remote entry system allows you to:• unlock the vehicle doors withouta key.• lock all the vehicle doors withouta key.• open the trunk without a key

The inside lights will not turn off if:• they have been turned on using the dimmer control or• any door is open.The battery saver feature will turn of

To replace the battery:1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIR

To reprogram the remote entrytransmitters:1. Ensure the vehicle is electronically unlocked.2. Put the key in the ignition.3. Turn the key from the 1 (

The inside lights will not turn off if:• they have been turned on with the dimmer control, or• any door is open.The battery saver will shut off the in

5. Turn the ignition back to the 4 (RUN) position. The horn will chirp.6. Press the unlock control, then press the lock control. The horn willchirp on

To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access e

Automatic disarmingSwitching the ignition to the 4 (RUN) position with a coded key disarmsthe vehicle.• The theft indicator will illuminate for three

Programming spare keysA maximum of eight keys can be coded to your vehicle. OnlySecurilock娂 keys can be used. To program a coded key yourself, youwill

PERIMETER ALARM SYSTEMThe perimeter anti-theft system will warn you in the event of anunauthorized entry to your vehicle.If there is any potential per

SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a

Using the manual lumbar supportThe lumbar control is located on thefront of the driver’s seat cushion.Turn to adjust lumbar support.Using the manual r

The driver and passenger seat must be in the upright positionand the lap belt must be snug and low across the hips while thevehicle is moving.Reclinin

Adjusting the passenger’s power seatThe control is located on the outboard side of the seat cushion.Press the control to move the seatforward or backw

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.All

1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and feelit latch.

Automatic locking modeHow to use the automatic locking mode• Buckle the combination lap andshoulder belt.• Grasp the shoulder portion andpull downward

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-

When to use the automatic locking mode• Anytime a child safety seat is installed in the vehicle. Refer to SafetyRestraints for Children or Safety Seat

Safety belt warning light and indicator chimeThe safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occup

If... Then...The driver’s safety belt is notbuckled before the vehicle hasreached at least 5 km/h (3mph) and 1-2 minutes haveelapsed since the ignitio

Reasons given... Consider...“I was in a hurry” Prime time for an accident.BeltMinder reminds us to take a fewseconds to buckle up.“Safety belts don’t

One time disableAny time the safety belt is buckled and then unbuckled during anignition ON cycle, the BeltMinder will be disabled for that ignition c

• This will disable BeltMinder if it is currently enabled, or enableBeltMinder if it is currently disabled.7. Confirmation of disabling BeltMinder is

Failure to inspect and if necessary replace the safety beltassembly under the above conditions could result in severepersonal injuries in the event of

Never place your arm over the air bag module as a deploying airbag can result in serious arm fractures or other injuries.Steps you can take to properl

How does the safety belt pretensioner and air bag supplementalrestraint system work?The safety belt pretensioner and airbag SRS are designed to activa

Several air bag system components get hot after inflation. Do nottouch them after inflation.If the air bag has deployed, the air bag will not function

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng

Passenger front and side air bag ON/OFF switchAn air bag ON/OFF switchhas been installed in thisvehicle. Before driving, alwayslook at the face of the

1. Insert the ignition key and turnthe switch to ON.2. The OFF light will brieflyilluminate when the ignition isturned to ON. This indicates thatthe p

occupant is not properly buckled up. The most effective way to reducethe risk of unnecessary air bag injuries, without reducing the overallsafety of t

This vehicle has special energy management safety belts for thedriver and right front passenger. These particular belts arespecifically designed to wo

This vehicle has special energy management safety belts for thedriver and right front passenger. These particular belts arespecifically designed to wo

How does the side air bag system work?The side air bag system consists ofthe following:• An inflatable nylon bag (air bag)with a gas generator conceal

If the side air bag hasdeployed, the air bag willnot function again. The sideair bag system (including theseat) must be inspected andserviced by a qua

Important child restraint precautionsYou are required by law to use safety restraints for children in the U.S.and Canada. If small children (generally

Booster seats position a child so that safety belts fit better. They lift thechild up so that the lap belt rests low across the hips and the kneesbend

• Those with a high back.A backless booster would be abetter choice because the highback booster will place the childcloser to the instrument paneland