Ford 2004 User Manual

Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 18Entertainment Systems 21How to get going 21AM/FM stereo with CD 25AM/FM stereo

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

In AM, FM1, or FM2 mode:• PressSEEK toselect preset stations within theselected radio band or press andhold to select the next/previousradio frequency

Press FAN + or - to adjust fanspeed.MOON ROOF (IF EQUIPPED)You can move the glass panel of the moon roof back to open or tilt up(from the closed posit

Bounce back override: To override bounce back, within 2 seconds afterreaching bounce back position, if the switch is held in the close positionthe moo

Info menuThis menu displays the following control displays:• Odometer/Trip Odometer (Trip A and Trip B)• Distance to Empty• Average Fuel Economy• Setu

• Variations in top-off procedure from one fill-up to another• Rounding of the displayed values to the nearest 0.1 gallon (liter)1. Drive the vehicle

The sequence of the system check report and how it appears in themessage center is as follows:1. OIL LIFE RESET2. CHARGING SYSTEM3. WASHER FLUID4. DOO

Units (English/Metric)1. Select this function from theSETUP MENU for the current unitsto be displayed.2. Press and hold theSELECT/RESET control switch

AutolockThis feature automatically locks all vehicle doors when the vehicle isshifted into any gear and when the vehicle is in motion over 13 mph(20 k

Oil Life Start Value1. Select this function from theSETUP MENU for the currentdisplay mode.2. Press and hold theSELECT/RESET control switch toreset oi

Compass zone adjustment (if equipped)1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap.2. Turn igniti

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng

1. Start the vehicle.2. Locate the reset button on the compass sensor mounted on the baseof mirror.3. To calibrate, press and hold thereset button on

Warning display StatusDoor ajar Warning cannot be resetFuel level low Warning returns after 10 minutesPark brake engagedCheck brake systemCheck park a

CHECK BRAKE SYSTEM. Displayed when the braking system is notoperating properly. If the warning stays on or continues to come on,contact your authorize

OIL CHANGE REQUIRED. Displayed when the engine oil liferemaining is 0%.An oil change is required whenever indicated by the message center andaccording

Selectable featuresResetPress the RESET control to selectand reset functions shown in theINFO menu, SETUP menu, textwarnings and reconfigurable tellta

DTE is calculated using a running average fuel economy, which is basedon your recent driving history of 500 miles (800 km). This value is notthe same

Fuel UsedSelecting this function from theINFO menu. “FUEL USED XXX.XGAL” will display the fuel used sincelast reset.The information displayedwill be i

System checkSelecting this function from theSETUP MENU causes the messagecenter to cycle through each of thesystems being monitored. For eachof the mo

2. Press RESET control to display“HOLD RESET IF NEW OIL”.3. Press and hold the RESETcontrol for more than 2 seconds. Oillife is set to 100% and “OILCH

1. Select this function from theSETUP MENU for the currentlanguage to be displayed.2. Press the RESET control to cyclethe message center through each

WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may

AutounlockThis feature automatically unlocks all vehicle doors when the driver’sdoor is opened within 10 minutes of the ignition being turned off.1. T

degrees between adjacent zones and will become noticeable as thevehicle crosses multiple zones. A correct zone setting will eliminate thiserror. Refer

7. Wait 4 seconds when correct zoneis chosen.Compass calibration adjustment (if equipped)Perform compass calibration in an open area free from steel s

Oil life Start Value1. Select this function from theSETUP control for the currentdisplay mode.2. Each press of the RESET controlreduces the value by 1

Warning display StatusDoor ajar Warning cannot be resetFuel level low Warning returns after 10 minutesPark brake engagedCheck brake systemCheck park a

CHECK BRAKE SYSTEM. Displayed when the braking system is notoperating properly. If the warning stays on or continues to come on,contact your authorize

OIL CHANGE REQUIRED. Displayed when the engine oil liferemaining is 0%.An oil change is required whenever indicated by the message center andaccording

Tailgate removalYour tailgate is removable to allowmore room for loading.1. Lower the tailgate.2. Use a screwdriver to pry thespring clip (on each con

CARGO CAGE (IF EQUIPPED)Your vehicle may be equipped with a cargo cage designed to extend thepickup box for larger loads.To extend the cargo cage:1. L

To remove the cargo cage:1. Extend the cargo cage.2. Pull the lever on each side of thecage to unlock it.Make sure the locking clip screwsare loose be

Note: Some Warning Lights will display in the Message Center as wordsand function the same as the warning light.Note: Depending on which options your

To open the rear panel:• Open the lock cover and unlockthe rear panel using your ignitionkey.• Lift the rear panel to access itemsin the pickup box.•

Interior tonneau cover releaseYour vehicle is equipped with a mechanical interior tonneau coverrelease handle that provides a means of escape for chil

CARGO AREA FEATURESCargo management systemThe cargo management system consists of a storage compartmentlocated in the floor of the pickup box.The stor

Interior tiedown hooksMounted inside the pickup box,each tiedown hook can secure loadsup to 200 lb. (90 kg). Total pickupbox cargo weight is not to ex

Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with alower center of gravity.

KEYSOne key operates the door, tailgate, and tonneau cover locks and startsthe vehicle. Always carry a spare key with you in case of an emergency.Your

Deactivating/activating autolockYour vehicle comes with the autolock feature enabled. There are fourmethods to enable/disable this feature:• Through y

4. Press and hold the 3 • 4. While holding the 3 • 4pressthe7• 8.5. Release the 7 • 8.6. Release the 3 • 4.The user should receive a horn chirp to ind

Power door unlock/lock procedureYou must complete Steps 1-5 within30 seconds or the procedure willhave to be repeated. If theprocedure needs to be rep

Power door lock/unlock inhibit feature (if equipped)If the key is not in the ignition, all doors are closed, and the vehicle hasbeen locked using the

• Optional instrument clusterBrake system warning light: Toconfirm the brake system warninglight is functional, it willmomentarily illuminate when the

CHILDPROOF DOOR LOCKS• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the outside when the

Your vehicle is equipped with a remote entry system which allows you to:• unlock the vehicle doors withouta key.• lock all the vehicle doors withouta

Locking the doors1. Press and release to lock all the doors. The lamps will flash. Note:If any door is not closed properly, the lamps will not flash u

2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board.3. Remove the old battery. Note: Please refer to local r

Note: Ensure the brake pedal is notdepressed during this sequence.To reprogram the remote entrytransmitters:1. Ensure the vehicle is electronically un

The inside lights will not turn off if:• they have been turned on with the dimmer control, or• any door is open.The battery saver will shut off the in

Tips:• Do not set a code that uses five of the same number.• Do not use five numbers in sequential order.• The factory set code will work even if you

SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEMSecuriLock娂 passive anti-theft system is an engine immobilizationsystem. This system is designed to help prevent

Automatic armingThe vehicle is armed immediatelyafter switching the ignition to the 2(ACCESSORY) position.The theft indicator will flash everytwo seco

Please read and understand theentire procedure before you begin.1. Insert the first previouslyprogrammed coded key into theignition.2. Turn the igniti

Safety belt: Reminds you to fastenyour safety belt. A Belt-Minder威chime will also sound to remind youto fasten your safety belt. Refer tothe Seating a

SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a

Adjusting the front manual seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle ismoving.Always drive and ride with your seat

Adjusting the front power seat (if equipped)Never adjust the driver’s seat or seatback when the vehicle ismoving.Do not pile cargo higher than the sea

The control is located on the outboard side of the seat cushion.Press front to raise or lower thefront portion of the seat cushion.Press rear to raise

Using the power lumbar support (if equipped)The power lumbar control is located on the outboard side of the seat.Press one side of the control toadjus

REAR SEATSFolding down the 2nd row 60/40 seatsEnsure that the head restraint is in the down position and no objectssuch as books, purses or briefcases

3. Lift up on the head restraint untilit locks into its original position.Before returning the seatback to its original position, make surethat cargo

How does the Personal Safety System姟 work?The Personal Safety System娂 can adapt the deployment strategy of yourvehicle’s safety devices according to c

because they are initially sitting very close to the airbag. For otheroccupants, this occurs when the occupant is not properly restrained bysafety bel

Front safety belt energy management retractorsThe front outboard safety belt energy management retractors allowwebbing to be pulled out of the retract

Never remove the coolant reservoir cap while the engine isrunning or hot.Low tire pressure warning:Illuminates when your tire pressureis low. If the l

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.All

• This safety belt system has a retractor assembly that is designed toextend the safety belt webbing in a controlled manner. This helpsreduce the belt

Vehicle sensitive modeThis is the normal retractor mode, which allows free shoulder belt lengthadjustment to your movements and locking in response to

• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl

the driver and right front passenger seating positions will be activatedwhen the respective seatbelt is properly buckled.The driver and front passenge

Second row comfort guideThe second row outboardlap/shoulder belt is equipped with abelt comfort guide. This guide isattached to the quarter trim panel

Use only extensions manufactured by the same supplier as the safetybelt. Manufacturer identification is located at the end of the webbing onthe label.

Both the driver’s and passenger’s safety belt usages are monitored andeither may activate the Belt-Minder威 feature. The warnings are the samefor the d

If... Then...The driver’s or frontpassenger’s safety belt becomesunbuckled for approximately1 minute while the vehicle istraveling at least 3 mph (5 k

Reasons given... Consider...“Traffic is light” Nearly 1 of 2 deaths occur insingle-vehicle crashes, many whenno other vehicles are around.“Belts wrink

AdvanceTrac威: Flashes when theAdvanceTrac威 with RSC system isactive. Illuminates solid when thesystem has been disabled (by thedriver or as a result o

Read Steps1-4thoroughly before proceeding with thedeactivation/activation programming procedure.Note: The driver and front passenger Belt-Minder威 feat

• This will enable the Belt-Minder威 feature for that seating position if itis currently disabled. As confirmation, the safety belt warning light willf

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right

Never place your arm over the airbag module as a deployingairbag can result in serious arm fractures or other injuries.To properly position yourself a

Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt

• one or more impact and safing sensors.• a readiness light and tone.• diagnostic module.• and the electrical wiring which connects the components.• F

For side airbag equipped vehicles, the front passenger sensing systemwill turn off the passenger seat side airbag if:• the seat is empty and safety be

• If the indicator lamp remains lit even after this, the person should beadvised to ride in the rear seat.OccupantPass Airbag OffIndicator LampPasseng

ObjectsPass Airbag OffIndicator LampPassenger AirbagSmall (i.e. 3 ringbinder, small purse,bottled water)Unlit DisabledMedium (i.e. heavybriefcase, ful

Turn signal: Illuminates when theleft or right turn signal or thehazard lights are turned on. If theindicators stay on or flash faster, check for a bu

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit.If the airbag readi

A difficulty with the system is indicated by one or more of the following:• The readiness light will eitherflash or stay lit.• The readiness light wil

automotive safety experts known as the Side Airbag Technical WorkingGroup. These recommended testing procedures help reduce the risk ofinjuries relate

Several air bag system components get hot after inflation. Do nottouch them after inflation.If the side airbag hasdeployed, the airbag willnot functio

To reduce risk of injury, do not obstruct or place objects in thedeployment path of the inflatable Safety Canopy娂.How does the Safety Canopy姟 system w

The Safety Canopy娂 system is designed to activate when the vehiclesustains lateral deceleration sufficient to cause the side crash sensor toclose an e

Any difficulty with the system is indicated by one or more of thefollowing:• The readiness light (same light as for front airbag system) will eitherfl

Children and safety beltsIf the child is the proper size, restrain the child in a safety seat. Childrenwho are too large for child safety seats (as sp

When children should use booster seatsChildren need to use booster seats from the time they outgrow thetoddler seat until they are big enough for the

• Those with a high back.If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boo

Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature,

Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the sto

Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in acollision.SAFETY SEATS F

tether anchors. For more information on top tether straps and anchors,refer to Attaching safety seats with tether straps in this chapter. Formore info

2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out and a

Attaching child safety seats with tether strapsMost new forward-facing child safety seats include a tether strap whichgoes over the back of the seat a

3. Locate the correct anchor for theselected rear seating position.• You may need to pull the seatback forward to access the tetheranchors. Make sure

5. Clip the tether strap to theanchor and return the seat back toits locked position. For Adrenalinvehicles fixed left rear seat, clip thetether hook

Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol:Never attach two LATCH child safe

you install a child seat at the center 2nd row position, use the vehiclebelt and the top tether anchor.Follow the child seat manufacturer’s instructio

Seating and Safety Restraints 150Seating 150Safety restraints 156Airbags 172Child restraints 186Tires, Wheels and Loading 200Tire information 202Tire

Trip odometer: Registers the miles (kilometers) of individual journeys.• Standard instrument clusterPress the SELECT/RESET controlonce to switch from

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary

• Narrower — to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUV’s and

government test course. For example, a tire graded 150 would wear oneand one-half (1 1/2) times as well on the government course as a tiregraded 100.

• Tire Identification Number (TIN): A number on the sidewall ofeach tire providing information about the tire brand andmanufacturing plant, tire size

At least once a month and before long trips, inspect each tire and checkthe tire pressure with a tire gauge (including spare, if equipped). Inflateall

To check the pressure in your tire(s):1. Make sure the tires are cool, meaning they are not hot from drivingeven a mile.If you are checking tire press

cracking, cuts, bruises and other signs of damage or excessive wear. Ifinternal damage to the tire is suspected, have the tire demounted andinspected

U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s

When mounting replacement tires and wheels, you should notexceed the maximum pressure indicated on the sidewall of thetire to set the beads without ad

AUDIO SYSTEMSQuick start — How to get goingListening to the radio1. If the audio system is off, pressVOL-PUSH to turn the radio on.Turn VOL-PUSH to ad

If your vehicle is stuck in snow, mud, sand, etc., do not rapidlyspin the tires; spinning the tires can tear the tire and cause anexplosion. A tire ca

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/

12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

Changing tires with TPMSEach road tire is equipped witha tire pressure sensor fastenedto the inside rim of the wheel.The pressure sensor is coveredby

When you believe your system is not operating properlyThe main function of the Tire Pressure Monitoring System is to warn youwhen your tires need air.

Listening to satellite radio (if equipped)1. If the audio system is turned off,press VOL-PUSH to turn the radioon. Turn VOL-PUSH to adjust thevolume.N

Low Tire PressureWarning LightPossible cause Customer Action RequiredFlashing WarningLightSpare tire in use Your temporary spare tire is inuse. Repair

any tire is under-inflated, carefully drive the vehicle to the nearestlocation where air can be added to the tires. Inflate all the tires to therecomm

Vehicle Curb Weight – is the weight of your new vehicle when youpicked it up from your authorized dealer plus any aftermarketequipment.Payload – is th

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

Exceeding any vehicle weight rating limitation could result inserious damage to the vehicle and/or personal injury.Steps for determining the correct l

transport the cement to your home? If you and your friend each weigh220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12 x 100) =1400 - 4

Follow these guidelines to ensure safe towing procedure:• Stay within your vehicle’s load limits.• Thoroughly prepare your vehicle for towing. Refer t

4x2GCWR (Gross Combined Weight Rating)/Trailer WeightEngine Rear axle ratio MaximumGCWR-lb. (kg)Trailer weightrange-lb. (kg)(0-Maximum)4.0L SOHC Class

For a single CD system, if a discis not already loaded, insert onlyone, label side up into the CD slot.LOADING CD and READING DISC will appear in the

4WDGCWR (Gross Combined Weight Rating)/Trailer WeightEngine Rear axle ratio MaximumGCWR-lb. (kg)Trailer weightrange-lb. (kg)(0-Maximum)4.0L SOHCClass

Safety chainsAlways connect the trailer’s safety chains to the frame or hook retainersof the vehicle hitch. To connect the trailer’s safety chains, cr

Driving while you towWhen towing a trailer:• Keep your speed no faster than 70 mph (112 km/h) during the first500 miles (800 km) of towing a trailer,

refilling your rear axle with synthetic gear lube if not already soequipped. Refer to the Maintenance and Specifications chapter forthe lubricant spec

Rear Wheel Drive (RWD) 4x2 vehicles:This applies to all 4x2 trucks/sport utilities with rear wheel drivecapability.• Place the transmission in N (Neut

STARTINGPositions of the ignition1. OFF/LOCK, shuts off the engineand all accessories/locks the steeringwheel, gearshift lever and allows keyremoval.2

If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smellexhaust fumes.Important saf

• Make sure the gearshift is inP (Park).3. Turn the key to 3 (ON) withoutturning the key to 4 (START).Some warning lights will briefly illuminate. See

Starting the engine1. Turn the key to 3 (ON) withoutturning the key to 4 (START). Ifthere is difficulty in turning the key,rotate the steering wheel u

To reduce the risk of electrical shock, do not use your heaterwith ungrounded electrical systems or two-pronged (cheater)adapters.BRAKESOccasional bra

Press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engageshuffle mode right away, press SEEK to begin random pl

Even when the ABS is disabled,normal braking is still effective. (Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake

Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.ADVANCETR

If your vehicle should become stuck in deep snow or mud, try switchingthe AdvanceTrac威 with RSC system off by pressing the AdvanceTrac威with RSC button

• Driving on slick surfaces.• Cornering while towing a heavily loaded trailer (refer to Trailertowing in the Tires, Wheels and Loading chapter.)Roll S

If the vehicle is above 25 mph (40 km/h), momentarily pressing theAdvanceTrac威 with RSC button will steadily illuminate the “sliding car”icon, however

Aggressive driving in any road conditions can cause you to losecontrol of your vehicle increasing the risk of severe personalinjury or property damage

PREPARING TO DRIVEUtility vehicles have a significantly higher rollover rate thanother types of vehicles.In a rollover crash, an unbelted person is si

2. Remove the rubber pad at thebottom of the cup holder to locatethe access cap of the floor shifterassembly.3. Using a screwdriver (orequivalent), re

Driving with a 5–speed automatic transmission (if equipped)This vehicle is equipped with an Adaptive Transmission Control Strategy.This Adaptive Trans

P (Park)This position locks the transmissionand prevents the rear wheels fromturning.To put your vehicle in gear:• Start the engine• Depress the brake

AM/FM Single CD/MP3 satellite compatible sound system(if equipped)Accessory delay: Your vehicle is equipped with accessory delay. Withthis feature, th

D (Drive) without OverdriveOverdrive can be deactivated bypressing the transmission controlswitch on the side of the gearshiftlever.• This position al

Forced downshifts• Allowed in D (Overdrive) or Drive.• Depress the accelerator to the floor.• Allows transmission to select an appropriate gear.Drivin

P (Park)This position locks the transmissionand prevents the rear wheels fromturning.To put your vehicle in gear:• Depress the brake pedal• Start the

D (Drive) without OverdriveOverdrive can be deactivated bypressing the transmission controlswitch on the side of the shift lever.• This position allow

• Allows upshifts by moving gearshift lever.• Will not downshift into 1 (First) at high speeds; allows for 1 (First)when vehicle reaches slower speeds

Certain add-on devices such as large trailer hitches, bike orsurfboard racks and any device that may block the normaldetection zone of the RSS system

If your vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone may be altered causinginaccurate measurement

mode is appropriate for severe winter and off-road conditions, such asdeep snow, ice or shallow sand.4X4 LOW (4WD Low) - Provides locked four-wheel dr

Drive cautiously to avoid vehicle damage from concealed objects such asrocks and stumps.You should either know the terrain or examine maps of the area

If your vehicle gets stuckIf your vehicle gets stuck in mud or snow it may be rocked out byshifting between forward and reverse gears, stopping betwee

3. MENU: Press repeatedly toaccess the following settings:CATEGORY (satellite radio if equipped): Press MENU until thecurrently active category appear

ParkingOn some 4WD vehicles, when the transfer case is in the N (Neutral)position, the engine and transmission are disconnected from the rest ofthe dr

Note: If your vehicle is equipped with the Tire Pressure MonitoringSystem (TPMS), the system indicator light may illuminate depending onhow much air i

“Tread Lightly” is an educationalprogram designed to increase publicawareness of land-use regulationsand responsibilities in our nationswilderness are

Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral;

Never drive with chains on the front tires of 4WD vehicles without alsoputting them on the rear tires. This could cause the rear to slide andswing aro

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

Canadian customers refer to your Customer Information Guidefor information on:• coverage period• exact fuel amounts• towing of your disabled vehicle•

HAZARD FLASHERThe hazard flasher is located on thesteering column, just behind thesteering wheel. The hazard flasherswill operate when the ignition is

FUEL PUMP SHUT-OFF SWITCHFUELRESETThe fuel pump shut-off switch is a device intended to stop the electricfuel pump when your vehicle has been involved

FUSES AND RELAYSFusesIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinth

The default setting is off; increasing your vehicle speed will not changethe volume level.Adjust 1–7: Increasing this setting from 1 (lowest setting)

Passenger compartment fuse panelThe fuse panel is located below theinstrument panel on the driver’sside.To remove a fuse use the fuse puller tool prov

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description7 15A Trailer tow stop/turn lamps8 15A Ignition switch power, PATS9 2A 6-sp

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description26 15A License plate lamps, Rear parklamps, Front park lamps, Manualclimate

The high-current fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription1 50A** BATT 2 (SJB)2 50A** BATT 3 (SJB)3

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription15 40A** Heated mirror16 40A** Blower motor17 30A** Trailer tow electronic brakes18 —

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription42 15A* Speed control deactivationswitch, EVMV, MAFS, HEGO,EVR, CMS, (VCT1, VCT2, CMC

Have a flat serviced by an authorized dealer in order to prevent damageto the TPMS sensor, refer to Changing tires with TPMS in the Tires,Wheels and L

• Use snow chains on the end of the vehicle with the dissimilar sparetire• Use more than one dissimilar spare tire at a time• Use commercial car washi

When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to:• Towing a trailer• Driving vehicles equipped with a

Location of the spare tire and toolsThe spare tire and tools for your vehicle are stowed in the followinglocations:Tool LocationSpare tire Under the v

5. SEEK: In radio mode,press/ to access theprevious/next strong station.In CD mode, press/ toaccess the previous/next CD track.In satellite radio mode

Removing the spare tire1. Assemble the jack handle to thelug wrench by sliding the squareend of the jack handle through theplastic grommet on the lug

Changing the spare tireTo help prevent the vehicle from moving when you change a tire,be sure the parking brake is set, then block the wheel that isdi

4. Position the jack according to theillustrated guides and turn the jackhandle clockwise until the tire is amaximum of 1 inch (25 mm) off theground.T

8. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torquespecifications later in this chapterfor the proper lu

Stowing the jack and tools1. Unblock the wheels.2. Stow the wheel ornament (if removed) in a safe location in the vehicle(such as the glove box or jac

JUMP STARTINGThe gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury orvehicle da

Connecting the jumper cables1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery.Note: In the illustrations,

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to the g

Do not connect the end of the second cable to the negative (-)terminal of the battery to be jumped. A spark may cause anexplosion of the gases that su

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

8. FOLDER : In folder mode,press FOLDERto access nextfolder on MP3 discs, if available.9.FOLDER: In folder mode,press FOLDER to access theprevious fol

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up

GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling

In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo

In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.Experience has sh

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformatio

ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro

To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov;or write to:

Maintenance and Specifications 308Engine compartment 310Engine oil 313Battery 318Engine coolant 320Fuel information 326Air filter(s) 340Part numbers 3

In satellite radio mode (if equipped), press and hold to hear a briefsampling of the next channels. Press again to stop. In CATEGORYMODE, press SCAN t

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is

• After polishing chrome bumpers, apply a coating of MotorcraftPremium Liquid Wax (ZC-53-A), available from your authorized dealer,or an equivalent qu

• To remove tar and grease, use Motorcraft Bug and Tar Remover(ZC-42), available from your authorized dealer.ENGINEEngines are more efficient when the

4.6L V8 Engine• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.PLASTIC (NON-PAINTED) EXTERIO

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft Premium Windshield Washer Concentrate (ZC-32-A),available from your au

1. Wipe up spilled liquid using a clean white cotton cloth.2. Apply Motorcraft Deluxe Leather and Vinyl Cleaner (ZC-11-A) [InCanada use Motorcraft Mul

• To help maintain its resiliency and color, use the Motorcraft DeluxeLeather Care Kit (ZC-11-D), available from your authorized dealer.• Do not use h

Motorcraft Premium Car Wash Concentrate (U.S. only) (ZC-17-B)Motorcraft Premium Glass Cleaner (Canada only) (CXC-100)Motorcraft Premium Liquid Wax (ZC

SERVICE RECOMMENDATIONS• Use the scheduled maintenance information to track routineservice.• Use only recommended fuels, lubricants, fluids and servic

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th

Audiophile AM/FM in-dash six CD/MP3 satellite compatible soundsystem (if equipped)Accessory delay: Your vehicle is equipped with accessory delay. With

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.0L SOHC V6 engine1. Engine oil filler cap2. Engine oil dipstick (out of view)3. Brake fluid reservoi

4.6L V8 engine1. Air filter assembly2. Engine oil filler cap3. Engine oil dipstick4. Brake fluid reservoir5. Power distribution box6. Battery7. Power

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

CHANGING THE WIPER BLADES1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to releas

• 4.0L V6 engine• 4.6L V8 engine6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.• If the oil level is between the lower a

• 4.0L V6 engine• 4.6L V8 engine• Oil levels above the upper hole may cause engine damage. Some oilmust be removed from the engine by an authorized de

To avoid possible oil loss, DO NOT operate the vehicle with theengine oil level indicator and/or the engine oil filler cap removed.Engine Oil Recommen

4.6L 3V V8 EngineLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils “Certified For Gasoline Engines” by the AmericanPetroleum

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyeswhen working near

2. MUTE/ : Press to mute theplaying media. Press again to returnto the playing media.3. MENU: Press repeatedly toaccess the following settings:CATEGOR

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

• 4.0L V6 engine• 4.6L V8 engine• The engine coolant should be at the “FULL COLD” level as listed onthe engine coolant reservoir (depending upon appli

Adding engine coolantWhen adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to the coolant reservo

For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when

Recycled engine coolantFord Motor Company does NOT recommend the use of recycled enginecoolant in vehicles originally equipped with Motorcraft Premium

• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures i

Oil overheat can be triggered in severe driving conditions, such astowing heavy loads over mountainous terrain in extreme hottemperatures. As oil temp

The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, wait until it stopsbefore completely rem

• Be particularly careful if you are taking “Antabuse” or other forms ofdisulfiram for the treatment of alcoholism. Breathing gasoline vapors,or skin

Fuel Filler CapYour fuel tank filler cap has an indexed design with a 1/4 turn on/offfeature.When fueling your vehicle:1. Turn the engine off.2. Caref

To search for specific RBDS music categories: When the desiredcategory appears in the display, press/ to find the desired type,then press and release

Choosing the right fuelUse only UNLEADED fuel or UNLEADED fuel blended with a maximumof 10% ethanol. Your vehicle was not designed to run on E85 fuels

“Regular” unleaded gasoline because it may cause these problems tobecome more pronounced. If the problems persist, see your authorizeddealer.Do not ad

possible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel economy. We do not recommendtaking fuel econ

3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current odometer reading.4. Subtract your initial odometer reading fro

• Resting your foot on the brake pedal while driving may reduce fueleconomy.• Combine errands and minimize stop-and-go driving.Maintenance• Keep tires

expected on the vehicle under optimum conditions. Your fuel economymay vary depending upon the method of operation and conditions.EMISSION CONTROL SYS

sells, leases, trades vehicles, or supervises a fleet of vehicles are notpermitted to intentionally remove an emission control device or preventit fro

Readiness for Inspection/Maintenance (I/M) testingSome state/provincial and local governments may haveInspection/Maintenance (I/M) programs to inspect

POWER STEERING FLUIDCheck the power steering fluid. Refer to scheduled maintenanceinformation for the service interval schedules.1. Start the engine a

TRANSMISSION FLUIDChecking automatic transmission fluidThe automatic transmission does not have an underhood transmissionfluid dipstick.Refer to your

COMPRESS (Compression): Available only in CD/MP3 mode. PressMENU until COMPRESS ON/OFF appears in the display.Use/ / SEEK, SEEK to toggle ON/OFF. When

DRIVELINE UNIVERSAL JOINT AND SLIP YOKEIf the original universal joints are replaced with universal joints equippedwith grease fittings, lubrication w

MOTORCRAFT PART NUMBERSComponent 4.0L SOHC V6 engine 4.6L 3V V8 engineAir filter element FA-1695 FA-1780Fuel filter FG-1083 FG-1083Battery BXT-65-650

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationBrake fluidBetween MIN an

Item CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationEngine oil 4.0L engine 5.0 quarts (4.7L)Motorcraft SAE 5W-30Premium Synthe

Item CapacityFord Part Name orequivalentFord Part Number /Ford SpecificationPower steering fluidFill between theMIN and MAXlines on reservoirMotorcraf

ENGINE DATAEngine 4.0L SOHC V6engine4.6L 3V V8engineCubic inches 245 281Required fuel 87 octane 87 octaneFiring order 1-4-2-5-3-6 1-3-7-2-6-5-4-8Ignit

IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli

1. World manufacturer identifier2. Brake type and gross vehicleweight rating (GVWR)3. Vehicle line, series, body type4. Engine type5. Check digit6. Mo

GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of

Peace of mindMobile-Ease娂 hands-free communication systemRemote startVehicle security systemsWheel locksNot all accessories are available for all mode

6. / Play/Pause: This controlis operational in CD and DVD mode(if equipped). When a CD or DVD isplaying in the FES system, press this control to play

AAccessory delay ...93AdvanceTrac ...241Air cleaner filter ...340–341Air conditioning ..

Climate control (see Airconditioning or Heating) ...73Clock adjust6-CD in dash ...32AM/FM/CD ...

Family entertainment system ...44Floor mats ...126Fluid capacities ...342Foglamps ...

Keys ...148positions of the ignition ...235LLampsbulb replacementspecifications chart ...81–82d

Rear seat entertainmentsystem ...44Relays ...269Remote entry system ...

changing ...275, 281checking the pressure ...206inflating ...204label ...

356

357

358

359

In satellite radio mode (if equipped), there are 18 available presets,six each for SAT1, SAT2 and SAT3. To save satellite channels in yourmemory prese

360

17. LOAD: Toloadadiscintothesystem, press LOAD. Select a slotnumber using memory presets 1–6.When the display reads LOAD CD#,load the desired disc, la

Auxiliary input jackYour vehicle is equipped with anAuxiliary Input Jack (AIJ). TheAuxiliary Input Jack provides a wayto connect your portable musicpl

Troubleshooting:1. Do not connect the audio input jack to a line level output. Line leveloutputs are intended for connection to a home stereo and are

CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth

CD/CD player careDo:• Handle discs by their edges only. Never touch the playing surface.• Inspect discs before playing. Clean only with an approved CD

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required.This m

Radio Display Condition Action RequiredNO TEXT Song title informationnot available.Song title informationnot available at thistime on this channel.The

Quick startYour Family Entertainment System includes a DVD system, two sets ofwireless infrared (IR) headphones and a wireless infrared (IR) remotecon

1. Ensure that the vehicle ignition is in the RUN or ACCESSORYposition.2. Insert a CD into the system,label-sideuptoturnontheDVDsystem. It will load a

2. Press the power button to turnthe DVD system on. The indicatorlight next to the power button willilluminate.3. Connect an auxiliary audio/videosour

Note: Channel A can access any possible media source (AM, FM1, FM2,SAT (if equipped), CD, DVD, AUX). Channel B can only access DVD andAUX sources.Note

DVD player controls1. Headphone control A/B: Pressto select either the A or Bheadphone source. Then pressMEDIA to select the desired playingmedia for

SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ

4. (Fast forward): Press andrelease for the next chapter ortrack. Press and hold to forwardsearch a DVD, Video CD, or FES CD in DVD/CD mode.5./ (Play/

11. / (Headphones/Speakers): Press once for Dual Play(Headphone mode- the rear speakers are muted) and press again forSingle Play (same media playing

Remote controlUnless otherwise stated, all operations can be carried out with theremote control. Always point the remote control directly at the playe

7. VOL (Volume): When in Single Play, press to increase ( )ordecrease () the volume over all speakers. When in Dual Play, press toincrease () or decre

22. ENTER: Press to select the highlighted menu option.23. ILLUMINATION: Press to illuminate the remote control andbacklight all of the buttons.Batter

HeadphonesWireless headphonesYour FES system is equipped with two sets of battery powered, infraredwireless headphones. Two AAA batteries are needed t

To operate the headphones:• Press ON/OFF on the ear piece toturn on the headphones. A redindicator light will illuminateindicating the headphones areO

Channel A source. The wired headphone jack for Channel B is located onthe right side of the FES and is labeledB. Headphones plugged intothis headphone

Press the Headphone Control buttonA to change the audio source forChannel A.Press MEDIA to change the audiosource for Channel A. Thisinformation will

Press MENU twice to access the DVD set-up menu and the followingfeatures:1. ZOOM2. ANGLE3. ASPECT RATIO4. LANGUAGE5. SUB TITLESAngle modeSelect ANGLE

SPECIAL NOTICESNew Vehicle Limited WarrantyFor a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited

You can select from: WIDE, LETTERBOX or PAN SCAN. Once you havemade your selection, press ENTERto confirm. The LCD screen displaywill immediately chan

Once you have made your selection,press ENTER to confirm. This isdisc dependent.Audio CDsTo play audio CDs on your DVD system:1. Ensure that the vehic

4. The folder, track and elapsedtime will appear in the status bar.The screen will list the Artist, Title,Album and File Name.COMP (Compression):Compr

CD, MP3 and CD player care• Handle discs by their edges only. Never touch the playing surface.• Do not expose discs to direct sunlight or heat sources

4. Use the DVD bezel controls to:Press to play or pause a DVD.Press to stop or eject a DVD.Press and release to go to theprevious chapter. Press and h

2. Press the right cursor button. TheDVD will advance one frame. Eachpress of the right cursor button willadvance the DVD video by oneframe.Headphone/

Audio displaysYour DVD system interacts closely with the front audio system. Statusmessages will appear in the radio display showing the DVD status. S

When the DVD system is ON, youcan then press the memory presetcontrols 2 and 4 simultaneously totoggle between Single Play and Dual Play. In Single Pl

The front glass on the liquid crystal display (LCD) flip-downscreen may break when hit with a hard surface. If the glassbreaks, do not touch the liqui

However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interferenceto radio

Event Data RecordingOther modules in your vehicle — event data recorders — are capable ofcollecting and storing data during a crash or near crash even

Cleaning the liquid crystal display (LCD) flip-down screenClean the display screen by applying a small amount of water or anyammonia-based household g

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele

• Remove any snow, ice or leaves from the air intake area at the base ofthe windshield.• To improve the A/C cool down when the vehicle interior issign

DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEM(IF EQUIPPED)1. A/C control: Press to turn onthe air conditioning. Press again toturn off the air cond

4. MAX A/C: Distributesrecirculated air through theinstrument panel vents to cool thevehicle. This recooling of theinterior air is more economical and

14. Driver’s side temperaturecontrol: Press to increase ordecrease the temperature on thedriver side of the cabin. This controlalso sets the passenger

To allow side window defogging and demisting while warming up thevehicle cabin:1. Select.2. Select A/C.3. Set the temperature control to maintain comf

HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Autola

Push the headlamp control towards the instrument panel to deactivatethe foglamps.Daytime running lamps (DRL) (if equipped)To activate DRL:• the igniti

PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel when exteriorlights are on.• Rotate the thumbwheel from leftto right to bright

Notice to owners of pickup trucks and utility type vehiclesUtility vehicles have a significantly higher rollover rate thanother types of vehicles.Befo

3. Turn on the low beam headlamps.The brightest part of the lightshould be below the horizontal line(4). If it is above the line theheadlamp will need

INTERIOR LAMPSMap lampsThe front map lamps are located inthe overhead console. Press thecontrols on either side of each maplamp to activate the lamps.

Using the right bulbsReplacement bulbs are specified in the chart below. Headlamp bulbsmust be marked with an authorized “D.O.T.” for North America an

Replacing headlamp bulbsDo not touch the glass of a halogen bulb.1. Turn off the headlamps and openthe hood.2. Remove three screws from theheadlamp as

Replacing front parking lamp/turn signal/sidemarker bulbs1. Turn off the headlamps and openthe hood.2. Remove three screws from theheadlamp assembly a

4. Rotate the bulb socketcounterclockwise and remove itfrom the lamp assembly.5. Pull the bulb straight out of thesocket.Reverse steps to reinstall bu

Replacing high-mount brake and cargo lamp bulbsMake sure the headlamp control isin the OFF position.1. Remove the two screws and movethe lamp assembly

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

TILT STEERING COLUMNPull the lever down and release, tounlock the steering column tilt lock.With the lever in the down position,tilt the steering colu

OVERHEAD CONSOLEThe appearance of your vehicle’s overhead console will vary according toyour option package.Storage compartmentPress the latch to open

Export Unique (Non United States / Canada) vehicle specificinformationFor your particular global region, your vehicle may be equipped withfeatures and

• Place the provided heightadaptors onto the back of thedoor as needed.• Close the door.• Press the depression in the doorto activate the transmitter.

Rear auxiliary power pointA second auxiliary power point is located on the rear side of the console.It is accessible from the rear seats.Truck bed aux

POWER WINDOWSDo not leave children unattended in the vehicle and do not letchildren play with the power windows. They may seriously injurethemselves.W

Window lockThe window lock feature allows onlythe driver to operate the powerwindows.To lock out all the window controlsexcept for the driver’s press

Press and release the control toopen window to the vent position.Press and release thecontrolagain to open window to the fullopen position.Press and r

up direction only. Down will be a one touch down operation. If thewindow is stalled in the down position and there are no other systemfaults, the moto

Fold-away mirrorsFold the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash.Heated outside mirrors(if equipped)B

SPEED CONTROLWith speed control set, you can maintain a set speed without keepingyour foot on the accelerator pedal.Do not use the speed control in he

Resuming a set speedPress the RES (resume) control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed.Increasing spee

Turning off speed controlThere are two ways to turn off the speed control:• Depress the brake pedal. This will not erase your vehicle’s previouslyset