Ford 2005 Freestar v.1 User Manual

Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 15Entertainment Systems 18AM/FM stereo 18AM/FM stereo with CD 20AM/FM stereo wi

WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A wa

Opening power liftgate (PLG) (if equipped)Press the control twice within three seconds to power open the powerliftgate. The interior lamps will illumi

Sounding a panic alarmPressto activate the alarm. The alarm will cycle the horn, the turnsignals will flash, and the interior lamps will illuminate.Pr

Replacing lost remote entry transmittersIf you would like to have your remote entry transmitter reprogrammedbecause you lost one, or would like to buy

The illuminated entry system will turn off the interior lights if:• the ignition switch is turned to the 4 (ON) position, or• the keyless entry system

You may also perform the following power door lock sequence toenable/disable the perimeter lamps feature:1. Turn the ignition to the 4 (ON) position,

Memory feature (if equipped)The remote entry system allows you to recall the memory seat/side viewmirrors/adjustable pedals feature.Pressto automatica

• recall memory seat/side view mirrors/adjustable pedals position Driver1 or Driver 2 (if equipped).The keypad can be operated with the factory set 5–

Tips for setting codes:• The factory set code cannot be erased or changed.• The factory code will work even after you have set your own personalcodes.

• the ignition is in the 4 (ON) position,• the brake is pressed before reaching 5 mph (8 km/h), and• then the vehicle increases to more than 5 mph (8

Spare coded keys may be purchased from an authorized Ford dealer. Anauthorized Ford dealer can also program your coded key, or you can doit yourself.

Check fuel cap: Illuminates whenthe fuel cap may not be properlyinstalled. Continued driving withthis light on may cause the Checkengine warning light

1. Insert the first previouslyprogrammed coded key into theignition and turn the ignition fromthe 3 (OFF) position to the 4 (ON)position [maintain ign

Arming the systemWhen armed, this system will help protect your vehicle fromunauthorized entry. When unauthorized entry occurs, the system willflash t

SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a

Always drive and ride with your seatback upright and the lapbelt snug and low across the hips.Lift handle to move seat forward orbackward.Pull lever u

Press to raise or lower the frontportion of the seat cushion.Press to raise or lower the rearportion of the seat cushion.Press the control to move the

Using the manual lumbar support (if equipped)The lumbar control is located on theinboard side of the seat under thearmrest.Rotate the control to chang

To program the memory feature to a remote entry transmitter and formore information on how to use the keypad, refer to Remote entrysystem in the Locks

Seat mounted cup holders (if equipped)Deploy by pressing the button ontop of the cupholder.The cupholder is designed to detach from the seat when subj

Adjusting 2nd row seats (if equipped)Lift control to adjust seat forward or backward.• 2nd row bucket seat (ifequipped)• 2nd row bench seat (if equipp

Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a collision.Ac

Safety belt: Reminds you to fastenyour safety belt. A chime will alsosound to remind you to fasten yoursafety belt.Check transaxle: Illuminates whena

Continuing to lift the handle willtumble the seat forward, allowingeasier access to the third row seat.After entering the 3rd row seat,return the seat

Second row bench seat tip slide feature1. Push the side easy-entry controlhandle forward and allow the seatback to flip forward.2. Push the seat forwa

After exiting the third row, pushrearward on the cushion of the seatto return the seat to its originalposition.Push the seatback rearward until itlatc

4. From inside the vehicle, pull upon front floor release handle(yellow).5. Rotate the seat rearward at a 30to 45 degree angle.6. With the assist hand

Second row bench seat1. Detach the lap/shoulder beltsfrom both sides of the seat byinserting a seat belt tongue or keyinto the buckle release slot, pu

3. Clip the end of the belt to thestationary portion of the shoulderbelt coming out of the trim panel.The end of the shoulder belt mustbe clipped in o

1. Position the seat in vehicle. Placefirst row seat in a forward positionto allow the second row seat to beinstalled.2. Install seat onto rear pin of

4. Rotate seat rearward until theback of the seat latches onto thefloor.5. Operate recline lever and pushthe seat back upright.Ensure seat is latched

3. Lower back of seat onto the reartubs until both release controls latchinto place. Be sure that the seat islocked in place both front and back.Do no

2. If you plan to carry very largeobjects or items that might damagethe center lap/shoulder belt, detachthe belt from the seat. Use a key orseat belt

Traction Control娂 or AdvanceTrac娂 active (if equipped):Illuminates when the Traction Control娂 is active, refer to the Drivingchapter for more informat

4. Store the belt in the housingfound on the ceiling by inserting thesmaller tongue in the slot provided.Note: The seat can be stowed withthe safety b

Important: If you don’t let go ofthe number 1 strap before the seatback folds completely, the seat maynot stow flat in the tub. Refer to thelabel atta

8. Pull the number 3 strap on the seat back to tumble seat all the way into the tub in the floor.Do not use the seat anchors as cargo tie downs.Unstow

2. To return the seat back to theseating position, pull the number 1strap, then while holding thenumber 1 strap, pull the number 3strap to raise the s

This is not a position suitable for driving. Do not drive thevehicle with the seat in this position. The safety belts are notfunctional when the seat

3. To return the seat, ensure seatlatching area is free of objects.Then, raise the seat off the liftgatescuff plate and push at the top ofthe seat bac

conditions. A collection of crash and occupant sensors providesinformation to the Restraints Control Module (RCM). During a crash, theRCM activates th

seat belts or child safety seats and they move forward during pre-crashbraking. The most effective way to reduce the risk of unnecessaryinjuries is to

manner in response to the occupant’s forward momentum. This helpsreduce the risk of force-related injuries to the occupant’s chest bylimiting the load

All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bagsupplemental restraint system (

Low washer fluid: Illuminates when the windshield washer fluid is low.• Without Message Center• With Message CenterDoor ajar: Illuminates when the ign

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle.All restraints in the vehicle are combination lap and shoulder belts.While

This mode should be used any time a child safety seat is installed in apassenger front or outboard rear seating position (if equipped). Children12 yea

Unbuckle the combination lap/shoulder belt and allow it to retractcompletely to disengage the automatic locking mode and activate thevehicle sensitive

The safety belt for the 3rd rowcenter occupant may be stowed inthe ceiling if it has been detachedfrom the seat to carry large cargo.Remove the safety

Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition...The safety belt war

If... Then...The driver’s and front passenger’ssafety belts are buckled before theignition switch is turned to the ONposition or less than 1-2 minutes

Reasons given... Consider...“Belts areuncomfortable”We design our safety belts to enhance comfort. Ifyou are uncomfortable - try different positions f

re-enable during the same ignition cycle if the occupant buckles andremains buckled for approximately 30 seconds. Confirmation is not givenfor the one

• This will enable the BeltMinder feature for that seating position if it iscurrently disabled. As confirmation, the restraint system warning lightwil

Refer to Interior in the Cleaning chapter.Replacing the front seat belt assemblies after a collisionThe front outboard safety belt assemblies have a s

• With Message CenterDisplays which bulb is burned out.Depress the RESET control to clear.High beams: Illuminates when thehigh beam headlamps are turn

Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in

Do not attempt to service, repair, or modify the air bagsupplemental restraint systems or its fuses. See your Ford orLincoln Mercury dealer.Modifying

How does the air bag supplemental restraint system work?The air bag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration suff

Several air bag system components get hot after inflation. Do nottouch them after inflation.If the air bag has deployed, the air bag will not function

• a front passenger takes his/her weight off the seat for a period of timeFor larger children and very small adults, the passenger sensing systemmay l

system to detect that person and then enable the passenger’s air bag. Ifthe indicator lamp remains lit even after this, then the occupant shouldbe adv

Relationship Center at the phone number shown in the CustomerAssistance section of this Owner’s Guide.Any alteration/modification to the front passeng

Do not attempt to service, repair, or modify the air bag SRS, itsfuses or the seat cover on a seat containing an air bag. See yourFord or Lincoln Merc

The air bag SRS is designed to activate when the vehicle sustains lateraldeceleration sufficient to cause the sensors to close an electrical circuitth

Do not lean your head on the door. The Safety Canopy娂 couldinjure you as it deploys from the headliner.Do not attempt to service, repair, or modify th

Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtemperature,

How does the Safety Canopy姟 system work?The design and development of theSafety Canopy娂 system includedrecommended testing proceduresthat were develop

The Safety Canopy娂 is mounted to roof side-rail sheet metal, behind theheadliner, along the entire side of the vehicle. In certain lateral collisionso

• The readiness light will not illuminate immediately after ignition isturned on.• A series of five beeps will be heard. The tone pattern will repeatp

Follow all the important safety restraint and air bag precautions thatapply to adult passengers in your vehicle.If the shoulder belt portion of a comb

• Is the shoulder belt centered on the shoulder and chest?• Can the child stay seated like this for the whole trip?Types of booster seatsThere are two

never use a booster seat with a lap belt only. It is best to use a boosterseat with lap/shoulder belts in the back seat- the safest place for children

When installing a child safety seat:• Review and follow the informationpresented in the Air BagSupplemental Restraint Systemsection in this chapter.•

Installing child safety seats with combination lap and shoulderbeltsAir bags can kill or injure a child in a child seat. NEVER place arear-facing chil

3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi

7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with your knee on thechild seat.

Trip odometer: Registers the miles (kilometers) of individual journeys.• Without Message CenterPress and release the button on thecluster to toggle be

The tether anchors in your vehicleare in the positions shown:The front passenger seat with power adjustment does not have atether anchor. The two teth

2. Route the child safety seat tetherstrap over the back of the seat. Ifthe head restraint is adjustable,route the tether strap under thehead restrain

If the tether strap is clippedincorrectly (as shown) thechild safety seat may not beretained properly in the event of acollision.5. Rotate the tether

Rear seating positionsFollow steps 1–7 as described above for the following available seats:• 2nd row bucket• 2nd row bench• 3rd row benchFor addition

Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol.If your vehicle has a second rowb

Follow the child seat manufacturer’s instructions to properly install achild seat with LATCH attachments.Attach LATCH lower attachments of the child s

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o

Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr

tread grooves. Check for holes or cuts that may permit air leakage fromthe tire and make necessary repairs.Also inspect the tire sidewalls for cuts, b

AM/FM STEREO SYSTEM (IF EQUIPPED)1./ Tuner: Press tomanually go up or down the radiofrequency. Also use in menu modeto select various settings.2. Audi

pressure should never be set lower than the recommended pressure onthe tire label or certification label.When weather temperature changes occur, tire

Only use replacement tires and wheels that are the same sizeand type (such as P-metric versus LT-metric or all-season versusall-terrain) as those orig

• If your low tire warning light is on, refer to Low tire warning in thischapter.The use of tire sealants is not recommended and may damageyour tires.

• try to repair the temporary spare tire or remove it from its wheel• use the wheel for any other type of vehicleUse of a temporary spare tire at any

• All-Wheel driving capability (if applicable)• Load leveling adjustment (if applicable)When driving with the dissimilar spare tire/wheel additional c

Removing the spare tire1. Wagon only: Open liftgate andlift flap in the carpeting on the reartub cargo floor to expose the hexnut. Insert the lug nut

3. Remove the primary retainer from the center of the tire. Unlock thesecondary (locking) retainer by rotating the top portion one-quarter turnand rem

• Secondary lock in locked positionNote: Do not stow the full size tire or any flat tire under the vehicle.Tire change procedureWhen one of the front

2. Place gearshift lever in P (Park),turn engine off, and block thediagonally opposite wheel.3. Remove the spare tire, jack andlug wrench.4. Removing

If Ford Accessory Running Boardshave been installed, use the jackadapters supplied with the runningboards as described on the inside ofthe jack storag

3. Seek: Press to access thenext/previous strong station ortrack.4. Memory presets: To set astation: Select frequency bandAM/FM; tune to a station, pr

11. Remove the jack and fullytighten the lug nuts in the ordershown. Refer to Wheel lug nuttorque specifications later in thischapter for the proper l

4. Check that the flat tire is properly secured.Stowing the spare tireNote: If no tire is to be stowed under the vehicle, attach the secondary(locking

tightness. Tighten to the best of your ability, to the point where theratchet/slip occurs, if possible. The spare tire carrier will not allow you toov

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/

12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

the road in adverse (wet, snowy, etc.) conditions. Visually check yourtires for uneven wear, looking for high and low areas or unusuallysmooth areas.

• Avoid potholes and objects on the road• Do not run over curbs or hit the tire against a curb when parkingIf your vehicle is stuck in snow, mud, sand

Seating and Safety Restraints 112Seating 112Safety restraints 135Air bags 149Child restraints 162Tires, Wheels and Loading 176Tire Information 177Chan

AM/FM STEREO/ SINGLE CD SOUND SYSTEM (IF EQUIPPED)1./ Tuner: Press tomanually go up or down the radiofrequency. Also use in menu modeto select various

your tires wear more evenly, providing better tire performance andlonger tire life. Unless otherwise specified, rotate the tires approximatelyevery 5,

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can

Tire pressure monitoring system (TPMS) (Direct system)(if equipped)When the Tire Pressure MonitoringSystem warning light is lit, one ormore of your ti

The tire pressure should be checked periodically (at least monthly) usingan accurate tire gauge, refer to Inspecting and inflating your tires inthis c

Low Tire WarningLightCustomer Action RequiredSolid Warning Light 1. Check your tire pressure to ensure they areproperly inflated, refer to Inspecting

therefore it may take up to a minute for the light to turn off after youhave filled your tires to the recommended tire pressure.• If your vehicle has

interference, and (2) This device must accept any interference received,including interference that may cause undesired operation.The Tire Pressure Mo

• The system will not detect a pressure loss without driving the vehiclefor at least 0.5 mile (0.8 km) at speeds greater than 25 mph (40km/h).Reset wi

• Vehicle speeds less than 20 mph (30 km/h), greater than 70 mph (120km/h) or driving duration less than 10 miles.• Transporting a heavy load or towin

capability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design performance. Before loadingyour vehi

Speed sensitive volume (if equipped): Radio volume automaticallychanges slightly with vehicle speed to compensate for road and windnoise. Press MENU t

GVW (Gross Vehicle Weight) – is the Vehicle Curb Weight + cargo +passengers.GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle.3. Subtract the combined weight of the driver and pas

TRAILER TOWINGYour vehicle is capable either of towing Class I trailers or up to Class IItrailers when equipped with the optional trailer tow package.

Vehicle towing capability/Trailer hitchrequirementTrailerModel/EngineGCWR - lbs(kg)Hitch typerequiredTrailer Weightrange - lbs (kg)Tongue loadVan, 3.9

Trailer brakesBe sure your trailer conforms to all applicable local and FederalRegulations regarding trailer braking. If your trailer is equipped with

Trailer towing tips• Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turni

STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo

Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,

• Turn the key to 4 (ON) withoutturning the key to 5 (START).Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to i

11. Rewind: Press to manuallyreverse in a CD track.12. Memory presets: To set astation: Select frequency bandAM/FM; tune to a station, press andhold a

1. Turn the key to 5 (START)without pressing the acceleratorpedal and release as soon as theengine starts. The key will return to4 (ON).2. When the en

BRAKESOccasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-o

Brake Assist (if equipped as part of the AdvanceTrac姟 system)The Brake Assist system provides full braking force during panic brakingsituations. It de

vehicle does not respond to steering inputs, the system will attempt toincrease the turning response of the vehicle.AdvanceTrac娂 enhances your vehicle

with a message center will also have CHECK ADVANCETRAC shown inthe display. Have the vehicle system serviced immediately.If the vehicle is stuck in sn

STEERINGTo prevent damage to the power steering system:• Never hold the steering wheel at its furthest turning points (until itstops) for more than a

When the key is in the 3 (OFF) position, the automatictransmission shift lever can be moved from the P (Park) positionwithout the brake pedal depresse

Understanding the gearshift positions of the 4–speed automatictransaxleP (Park)This position locks the transaxle and prevents the front wheels fromtur

1 (First)• Transaxle operates in first gear only.• Provides maximum engine braking.• Allows upshifts by moving gearshift lever.• Will not downshift in

To help avoid personal injury, always use caution when in R(Reverse) and when using the RSS.This system is not designed to prevent contact with small

PREMIUM IN-DASH SIX CD SOUND SYSTEM (IF EQUIPPED)1./ Tuner: Press tomanually go up or down the radiofrequency. Also use in menu modeto select various

The RSS is automatically enabledwhen the gear selector is placed inR (Reverse) and the ignition is ON.The park aid disable switch allowsthe driver to

GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program

Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will

This switch is located behind theservice panel on the right side ofthe cargo area.To reset the switch:1. Turn the ignition OFF.2. Check the fuel syste

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey ———3A Violet Vio

The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingPassenger Compartment Fuse PanelDescription1 Relay Accessory delay relay 12 Relay Acces

Fuse/RelayLocationFuse AmpRatingPassenger Compartment Fuse PanelDescription13 5A Compass/Driver heated seat/Passengerheated seats/Reverse sensingsyste

Power distribution boxThe power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that prot

Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description5 30A** Right-hand power sliding door6 30A** SJB accessory #2 (driver powerwindow)7

Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description40 15A* Engine #1 (A/C relay coil, IMRC, HEGOsensors, Canister purge, Transaxle,Cani

Speed sensitive volume (if equipped): Radio volume automaticallychanges slightly with vehicle speed to compensate for road and windnoise. Press MENU t

Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description62 30A* SJB #3 – Right cornering/auxiliarylamps, Right low beam, Left frontpark/turn

Auxiliary relay box (cooling fans)The relay box is located in the engine compartment by the radiator.Fuse/RelaylocationFuse ampratingDescription1 — Co

Do not attempt to push-start your vehicle. Automatictransmissions do not have push-start capability; doing so maydamage the catalytic converter.Prepar

2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarbureto

Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli

In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo

10. Fast forward: Press tomanually advance in a CD track.11. Rewind: Press to manuallyreverse in a CD track.12. Memory presets: To set astation: Selec

In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a

THE DISPUTE SETTLEMENT BOARD (U.S. ONLY)The Dispute Settlement Board is:• an independent, third-party arbitration program for warranty disputes.• avai

Board membershipThe Board consists of:• Three consumer representatives• A Ford or Lincoln Mercury dealership representativeConsumer candidates for Boa

Oral presentationsIf you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral

unsatisfactory, Ford of Canada participates in an impartial third partymediation/arbitration program administered by the Canadian MotorVehicle Arbitra

details about Ford Extended Service Plan coverage options, or visit theFord ESP website at www.ford-esp.com.GETTING ASSISTANCE OUTSIDE THE U.S. AND CA

Or call:For a free publication catalog, order toll free: 1-800-782-4356Monday-Friday 8:00 a.m. - 6:00 p.m. ESTHelm, Incorporated can also be reached b

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is

sliding door. If necessary, clean the contacts with Motorcraft Bug andTar Remover (ZC-42) to remove any sealant. Do not use any abrasiveson the contac

• Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all partsthat require cleaning and pressure rinse clean.• Cover the highlighted areas to pr

19. CD eject: Press to eject a CD,then select the desired CD slotusing the radio presets 1 through 6.If a slot is not selected within 5 seconds, the r

• Do not use fuel, kerosene, or paint thinner to clean any parts.• Wiper blades can be cleaned with isopropyl (rubbing) alcohol orwindshield washer so

Do not use cleaning solvents, bleach or dye on the vehicle’ssafety belts, as these actions may weaken the belt webbing.Do not use chemical solvents or

FORD, LINCOLN AND MERCURY CAR CARE PRODUCTSYour Ford, Lincoln or Mercury dealer has many quality products availableto clean your vehicle and protect i

SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.9L/4.2L V6 engines1. Brake fluid reservoir2. Air filter assembly3. Power distribution box4. Battery5

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

4. Open the hood. Protect yourself from engine heat.5. Locate and carefully remove theengine oil level indicator (dipstick).6. Wipe the indicator clea

3. Recheck the engine oil level. Make sure the oil level is not above theMAX mark on the engine oil level indicator (dipstick).4. Install the indicato

It is recommended you use the appropriate Motorcraft oil filter (oranother brand meeting Ford specifications) for your engine application.BATTERYYour

4. Menu: Press to toggle throughthe following modes:Treble: Press to adjust the treble setting. Use/ / SEEK .Bass: Press to adjust the bass setting. U

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a

7. Drive the vehicle to complete the relearning process.• The vehicle may need to be driven 10 miles (16 km) or more torelearn the idle and fuel trim

• Freeze protection down to -34°F (-36°C).• Boiling protection up to 265°F (129°C).• Protection against rust and other forms of corrosion.• Enables ca

Adding engine coolantWhen adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to the coolant reservo

For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when

Recycled engine coolantFord Motor Company does NOT recommend the use of recycled enginecoolant in vehicles originally equipped with Motorcraft Premium

• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures i

swallowed can cause death or permanent injury. If fuel is swallowed,call a physician immediately, even if no symptoms are immediatelyapparent. The tox

• DO NOT use a device that would hold the fuel pump handle in the fillposition.Fuel Filler CapYour fuel tank filler cap has an indexed design with a 1

these additives can cause your vehicle’s emission control system todeteriorate more rapidly. In Canada, premium grade fuel generallycontains more meta

5. AUX: Press to toggle betweenFES/DVD and AUX modes. If noauxiliary sources are available, NOAUX AUDIO will be displayed. To return to radio mode, pr

Cleaner airFord endorses the use of reformulated “cleaner-burning” gasolines toimprove air quality.Running out of fuelAvoid running out of fuel becaus

amount of fuel in a full tank and a tank when the fuel gauge indicatesempty. Empty reserve is the small amount of fuel remaining in the fueltank after

economy under current driving conditions. Additionally, keeping recordsduring summer and winter will show how temperature impacts fueleconomy. In gene

• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in your vehicle sche

• Do not turn off the ignition while your vehicle is moving, especially athigh speeds.• Have the items listed in your Scheduled Maintenance Guideperfo

service technician in properly servicing your vehicle. When the Checkengine/Service engine soon light illuminates, the OBD-II system hasdetected a mal

CHECKING AND ADDING POWER STEERING FLUIDCheck the power steering fluid.Refer to the scheduled maintenanceguide for the service intervalschedules. If a

However, the fluid level should be checked if the transaxle is not workingproperly, i.e., if the transaxle slips or shifts slowly or if you notice som

The transmission fluid should be inthis range if at normal operatingtemperature (66°C-77°C[150°F-170°F]).High fluid levelFluid levels above the safe r

Changing the air filter element1. Disconnect the Mass Air FlowSensor from the air outlet tube.2. Reposition the locking clip (onthe connector) and squ

16. AM/FM: Press to select AM/FMfrequency band.17. ON/OFF/Volume: Press to turnON/OFF. Turn to increase/decreasevolume.If the volume is set above a ce

4. Remove the air cleaner assemblyfrom the vehicle.5. Release the two clamps thatsecure the cover to the air filterhousing and place the cover aside.6

9. Replace the air filter housingcover and secure the clamps. Besure all the tabs on the bottom edgeare properly aligned.10. Reinstall the air cleaner

11. Ensure the pads on the bottomof the air cleaner assembly areproperly seated.12. Reconnect the outlet tube to theair cleaner assembly and tighten t

MOTORCRAFT PART NUMBERSComponent 3.9L OHV V6 engine 4.2L OHV V6 engineAir filter element FA-1679 FA-1679Battery BXT-59 BXT-59BXT-65-750 BXT-65-750Fuel

REFILL CAPACITIESFluid Ford PartNameApplication CapacityBrake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluid1All Fill to MAX lineon res

3Use of synthetic or synthetic blend motor oil is not mandatory. Engineoil need only meet the requirements of Ford specificationWSS-M2C930-A and the A

Item Ford partnameFord partnumberFordspecificationDoor latch, hoodlatch, auxiliaryhood latch, doorand liftgatehinges, strikerplates, seattracks, slidi

1Use only brake fluids certified to meet Ford specifications. DOT 3 fluidis recommended. However, if DOT 3 is not available, DOT 4 fluid can beused.2E

14REVIEW COPY2005 Freestar (win), Owners Guide (post-2002-fmt) (own2002),Market: USA_English (fus)Maintenance and Specifications298

IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt

Maintenance and Specifications 263Engine compartment 265Engine oil 266Battery 269Fuel information 276Air filter(s) 289Part numbers 293Refill capacitie

AUXILIARY AUDIO CONTROLS (IF EQUIPPED)Your vehicle may be equipped with auxiliary audio controls. This featureallows the front and middle seat passeng

1. World manufacturer identifier2. Brake type and gross vehicleweight rating (GVWR)3. Vehicle line, series, body type4. Engine type5. Check digit6. Mo

complete listing of the accessories that are available for your vehicle,please contact your dealer or visit our online store at:www.fordaccessoriessto

communications systems — such as two-way radios, telephones andtheft alarms - that are equipped with radio transmitters. Any suchequipment installed i

AAccessory delay ...68AdvanceTrac ...222Air bag supplemental restraintsystem ...149–150

washing ...257waxing ...257wheels ...258wiper bl

FFloor mats ...75Fluid capacities ...294Fuel ...276calc

LLampsautolamp system ...45bulb replacementspecifications chart ...51daytime running light ...46headlam

Remote entry system ...99illuminated entry ...47, 102–103locking/unlocking doors ...95, 99Reverse sensing system ...228Road

Transaxleautomatic operation ...225fluid, refill capacities ...294lubricant specifications ...297Transmissionbrake-shift

309

PARENTAL CONTROLSimultaneously press the radiopreset controls 3 and 5 toenable/disable the rear seat audiocontrols as well as the Family Entertainment

310

311

312

RADIO RECEPTION FACTORSThere are three factors that can affect radio reception:• Distance/strength: The further you travel from an FM station, theweak

CD units are designed to play commercially pressed 4.75 in (12cm) audio compact discs only. Due to technical incompatibility,certain recordable and re

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow sele

Operating tips• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up

DUAL ZONE MANUAL HEATING AND AIR CONDITIONING SYSTEMWITH REAR PASSENGER COMPARTMENT CLIMATE CONTROL(IF EQUIPPED)1. Air flow selections: Controlsthe di

will be warmer or cooler than the driver airflow temperature settingwhen more than one rear temperature light (REAR )isilluminated.5.RRear defrost: Pr

In the and modes:• Move the temperature control selector to the coldest setting.• Select A/C and recirculated air. Use with A/C to providecolder airfl

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITH REARPASSENGER COMPARTMENT CLIMATE CONTROL (IF EQUIPPED)1.Defrost: Distributes outside air through the win

CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth

engaged manually in any airflow selection except . Recirculated airmay turn off automatically in all airflow selections.7. A/C: Press to activate/deac

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITHHEATED SEATS AND REAR PASSENGER COMPARTMENTCLIMATE CONTROL (IF EQUIPPED)1.Defrost: Distributes outside air

7. :Distributes air through the windshield defroster vents and thefloor vents.8.: Distributes air through the floor vents.9.: Distributes air through

19. REAR: Press to enable the control located in the rear seat. Pressagain to turn the auxiliary system off.OPERATING TIPS• To reduce fog build up on

AUXILIARY CLIMATE CONTROL (IF EQUIPPED)1. Fan speed: Turn to select thedesired fan speed.2. Temperature/mode selection:The distribution of air from th

HEADLAMP CONTROLTurns the lamps off.Turns on the parking lamps,instrument panel lamps, licenseplate lamps and tail lamps.Turns the headlamps on.Note:

2. Deselect the auto lamps.3. Put the ignition in RUN.4. Put the ignition in OFF.5. Select the autolamps.• Note: Steps 2 through 5 must be performed w

Flash to passPull toward you slightly to activateand release to deactivate.Battery saverThe battery saver will shut off the exterior lamps and interio

Domelamp ControlThe panel dimmer control also controls the domelamp operation.• Rotate the thumbwheel fully to the right, past detent to activate thed

4. On the wall or screen you willobserve a light pattern with highintensity flat segments at the topedge of the pattern. If the flat edgesare not at t

SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ

Map lamps (if equipped)The map lamps and controls arelocated on the center overheadconsole. Press the raised portion oneach lens to activate the lamps

door is opened. If the control is moved to the driver’s side position, thelamp will not come on at all.The dome lamp will illuminate whenever a front

Function Trade NumberRear license plate lamps W5WLHigh-mount brake lamp LED (see dealer)Rear tail/stop/turn lamps 3157KBackup lamps 3156KDome lamp (fr

3. Disconnect the electricalconnector from the bulb by pullingrearward and unlock the bulb byrotating it counterclockwise.Handle a halogen headlamp bu

4. To remove the parking/turnbulb, turn the socket on the bottomof the headlamp assemblycounterclockwise and pull the bulbstraight out of the socket.I

Replacing license plate lamp bulbThe license plate bulbs are located in the license plate housing assemblyon the liftgate. To change the license plate

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

Changing the wiper blades1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to releas

ILLUMINATED VISOR MIRROR (IF EQUIPPED)Lift the mirror cover to turn on thevisor mirror lamp.Slide on rod feature (ifequipped)Rotate the visor towards

Electronic compass/temperature display (if equipped)The overhead console may have an electronic compass and outside airtemperature display. The compas

SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and

Zone variation mode1. Determine which magnetic zoneyou are in by referring to the zonemap.2. Turn the ignition to the ONposition.3. Press and hold the

Note: Look for a parking lot away from buildings, light posts, manholecovers, sewer and drainage grates and other metallic objects. Somemagnetic objec

Manual door operation when vehicle is stopped or parked on adownhill gradeIn some cases it may be necessaryto have someone hold the doorwhile rear sea

The sliding door must be unlocked for the PSD to power open from therear trim switches and the inside or outside PSD handles. The fuel fillerdoor must

• Manually pull the inside or outside sliding door handle to engage thepower assist feature. Release the handle as soon as the PSD begins topower open

Resetting the PSDThe power sliding door may operate incorrectly or not at all because ofthe following conditions:• a low voltage or dead battery• the

To open the sliding door when thechild safety lock is on:• Unlock the sliding door and openthe door from the outside.• Press the right or left handcon

Do not use the power point for operating the cigarette lighter element.The Maximum power each power point can supply depends on the fuserating. For ex

POWER WINDOWSDo not leave children unattended in the vehicle and do not letchildren play with the power windows. They may seriously injurethemselves.W

Power vent windowsThe power vent windows areoperated by a single switch locatedon the instrument panel. Press andhold the bottom of the switch toopen

Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Supplemental restraint

Heated outside mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated.Do not re

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED)The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is

3. Press the SET + control andrelease it.4. Take your foot off the acceleratorpedal.5. The indicatorlight on theinstrument cluster will turn on.Note:•

• Use the accelerator pedal to get to the desired speed. When thevehicle reaches that speed press and release the SET + control.Reducing speed while u

STEERING WHEEL CONTROLS (IF EQUIPPED)RADIO CONTROL FEATURES• Press MEDIA to select AM, FM1,FM2, TAPE or CD (if equipped).In Radio mode:• Press SEEK to

Mobile Communication Equipment includes, but is not limited to cellularphones, pagers, portable email devices, in vehicle communicationssystems, telem

Retain the original transmitter for use in other vehicles as well as forfuture programming procedures (i.e. new HomeLink威 equipped vehiclepurchase). I

5. Press and hold the just-trained HomeLink威 button and observe theindicator light. If the light is constant, programming is complete and yourdevice s

• Continue to press and hold the HomeLink威 button (note step 3 in the“Programming” section) while you press and release — every twoseconds (“cycle”) y

2. The indicator light will begin to flash after 20 seconds. Withoutreleasing the HomeLink威 button, follow step 2 in the “Programming”section.For ques

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-

Distance to empty (DTE)Selecting this function from theINFO menu estimates approximatelyhow far you can drive with the fuelremaining in your tank unde

Trip elapsed drive timeSelect this function from the INFOmenu to display your trip elapseddrive time. When selected thedisplay will accumulate when th

3. Press and hold the RESETcontrol for 2 seconds to set thelanguage choice.Units (English/Metric)1. Select this function from theSETUP menu for the cu

System warningsSystem warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems.In the event of a multiple warning si

Liftgate ajar Warning returns after the ignition keyis turned from OFF to ONCheck left park lampCheck right park lampCheck left headlampCheck fuel cap

PARK BRAKE SET. Displayed when the manual park brake is set. Ifthe warning stays on after the park brake is released, contact your dealeras soon as po

CHECK TIRES/LOW TIRE PRESSURE (if equipped). Displayedwhen one or more tires on your vehicle have low tire pressure. Refer toInspecting and Inflating

2. Press and release the RESETcontrol to display “OIL LIFE XX%HOLD RESET NEW”.3. Press and hold the RESETcontrol for 2 seconds to display “IFNEW OIL H

4. Release the RESET controlmomentarily, then press RESET andSETUP controls at the same time toactivate a service mode which willdisplay “OIL LIFE XX%

Make sure that the liftgate door is closed to prevent exhaustfumes from being drawn into the vehicle. This will also preventpassengers and cargo from

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng

The Power Door Lockout Control islocated in the overhead console.With the control in the OFFposition, power operation is disabledfrom the liftgate han

Note: Continued force applied after unlatching may activate the obstacledetection feature and stop the power system. For the best performanceallow the

If any of these conditions occur, the PLG must be reset. To reset thePLG:1. Manually close and fully latch the liftgate.2. Power open the liftgate by

Utility hooksThe utility hooks can be used tohang small items. Do not hang morethan 12 kg (20 lbs.) on each of thehooks. The hooks are not designedto

To remove the cross-bar (if equipped) assembly:1. Loosen the thumbwheel (2) at both ends of the cross-bar (1) andslide the cross-bar (1) to the end of

KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w

remote entry keypad (if equipped), or using the lock button on theremote entry transmitter (if equipped).Childproof door locks• When these locks are s

• For vehicles without powerliftgate, pull the lock/unlock leverto the right (drivers side).• For vehicles with power liftgate,pull the lock/unlock le

• 3–button remote• 5–button remote• 6–button remoteThe remote entry system allows you to:• lock or unlock all vehicle doors and liftgate without a key

If there is any potential remote keyless entry problem with your vehicle,ensure ALL remote entry transmitters are taken to your authorizeddealer to ai