Ford 2012 F-550 v.3 User Manual

Introduction 4Instrument Cluster 14Warning lights and chimes 14Gauges 21Message center 23Entertainment Systems 61AM/FM stereo 61AM/FM stereo with CD 6

Additionally, when you connect to Traffic, Directions andInformation (if equipped, U.S. only), the service uses GPStechnology and advanced vehicle sen

TILT/TELESCOPE STEERING WHEELTo adjust the steering wheel:1. Pull the lever down to unlock thesteering column.2. While the lever is in the downpositio

OVERHEAD CONSOLE (IF EQUIPPED)The appearance of your vehicle’s overhead console will vary according toyour option package.Storage compartment (if equi

• Two removable front cupholdermodules• Removable false bottom tray foraccessing hidden storagecompartment (also has space fora large cup)WARNING: Use

To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe ba

The power point can switch to a fault mode when it is overloaded,overheated, or shorted. For overloading and shorting conditions, unplugyour device an

Rear Window Buffeting: When one or both of the rear windows areopen, the vehicle may demonstrate a wind throb or buffeting noise. Thisnoise can be all

Accessory delayWith accessory delay, the window switches may be used for up to10 minutes after the ignition switch is turned to the off position or un

To adjust your mirrors:1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror.2. Mo

To operate the power-fold mirrors:1. Rotate the switch to the center/neutral position.2. Momentarily pull the switch rearward to auto fold in.3. Momen

Note: If the power fold/telescope mirror glass appears loose or vibrateswhen driving, it is possible that the mirrors have been manually folded ortele

Mobile communication equipment includes, but is not limited to, cellularphones, pagers, portable email devices, text messaging devices andportable two

Mirror-mounted side turn signal indicator (if equipped)When the vehicle turn signals areactivated, the outer portion of themirror housing will blink a

The accelerator and brake pedal positions are saved when doing amemory set function and can be recalled along with the vehiclepersonality features whe

Note:• Vehicle speed may vary momentarily when driving up and down asteep hill.• If the vehicle speed increases above the set speed on a downhill, you

STEERING WHEEL CONTROLS (IF EQUIPPED)Audio control featuresMEDIA: Press repeatedly to scrollthrough available audio modes.SEEK :Press to selectthe pre

For further information on the SYNC威 system, refer to the SYNC威supplement.Navigation system/SYNC威 handsfree control features (ifequipped)Press VOICE b

The relays are coded as shown inthe accompanying illustration.There will also be one power leadfor each switch found as a blunt-cutand sealed wire loc

WARNING: When closing the moon roof, you should verify thatit is free of obstructions and ensure that children and/or pets arenot in the proximity of

Car2U姞 Home Automation System (if equipped)The Car2U威 Home AutomationSystem is a universal transmitterlocated in the driver’s visor thatincludes two p

• Fixed code garage door openers were produced prior to 1996. Fixedcode uses the same coded signal every time. It is manuallyprogrammed by setting DIP

1. Firmly press the two outerCar2U威 system buttons for1–2 seconds, then release.2. Go to the garage to locate thegarage door opener motor and its“lear

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

After successful programming, you will be able to operate your Car2U威system by pressing the button you programmed to activate the opener.The indicator

Switchposition 12345678 9101112Up, onor +LLLLLLLLLLLLMiddle,neutralor 0MMMMMMMMMMMMDown,offor–RRRRRRRRRRRRL=left; M=middle; R=right3. To input these p

After successful programming, you will be able to operate your Car2U威system by pressing the button you programmed to activate the opener.The indicator

POSITIVE RETENTION FLOOR MAT (IF EQUIPPED)WARNING: Always use floor mats that are designed to fit thefoot well of your vehicle. Only use floor mats th

WARNING (Continued)• Failure to properly follow floor mat installation or attachmentinstructions can potentially cause interference with pedal operati

1. Before removal of the tailgate,locate and disconnect the tailgatein-line connector under the pickupbox on the passenger side of thevehicle near the

Tailgate step (if equipped)Your vehicle may be equipped with a feature that allows easier entry intothe truck bed. To open the tailgate step:1. Flip d

Note:• Fully close and latch the tailgate step before moving the vehicle.• Never drive with the step or grab handle deployed.• Replace slip resistance

3. Rotate the panels toward thetailgate.Repeat Steps 1–3 for the other side of the bed extender.4. Connect the two panels, then rotate both knobs a qu

Note: When the vehicle is in motion, ensure the locking pins and knobsare fully engaged.Note: Ensure all cargo is secured.Note: When the vehicle is in

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

KEYSYour vehicle may be equipped withtwo integrated keyhead transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and

MyKey威 restricted featuresStandard settings – These settings cannot be changed• The audio system will be muted whenever Belt-Minder威 is activateduntil

4. Wait until KEY RESTRICTED AT NEXT START is displayed.For optional message center:1. At the main menu screen select SETTING then MYKEY by pressingOK

For optional message center:1. At the main menu screen select SETTING then MYKEY by pressingOK or the right arrow key.2. Use the up and down arrows to

Refer to Message center in the Instrument Cluster chapter for MyKey威system warnings displays.Using MyKey威 with remote start systemsMyKey威 is not compa

Note: For all vehicles, the number of MYKEY(S) PROGRAMMED orADMIN KEYS PROGRAMMED that is displayed in the MyKey威 systemstatus menus will include the

TroubleshootingCondition Potential CausesCan’t create a MyKey威 • Key in the ignition is already a MyKey威.• Key in the ignition is the last remainingad

Condition Potential CausesI accidentallyprogrammed all keys asMyKeys威• Vehicle has a non Ford-approved remotestart system that is recognized as an adm

POWER DOOR LOCKS (IF EQUIPPED)Press control to unlock all doors.Press control to lock all doors.Smart locks (if equipped)This feature prevents you fro

The autolock feature repeats when:• any door is opened then closed while the ignition is in the on positionand the vehicle speed is 9 mph (15 km/h) or

WARNING LIGHTS AND CHIMESBase instrument cluster with standard measure shown; metricsimilarOptional instrument cluster with standard measure shown; me

Keyless entry keypad autolock enable/disable procedure1. Turn the ignition to the offposition.2. Close all the doors.3. Enter factory–set 5–digit entr

Power door lock switch autounlock enable/disable procedureBefore starting, ensure the ignition is in the off position and all vehicledoors are closed.

CHILDPROOF DOOR LOCKS (IF EQUIPPED)• When these locks are set, therear doors cannot be opened fromthe inside.• The rear doors can be openedfrom the ou

The typical operating range for your IKT is approximately 33 feet(10 meters). A decrease in operating range could be caused by:• weather conditions,•

Switching from two step to one step door unlockingYour vehicle comes with two step unlocking enabled. Unlocking can beswitched between two step and on

Programming memory feature to transmitterTo activate this feature:1. Move the driver seat, power mirrors, and adjustable pedals to thedesired position

Integrated keyhead transmitter (IKT)To replace the battery:1. Twist a thin coin in the slot nearthe key ring to remove the batterycover (1).Note: Do n

Illuminated entryThe interior lamps and parking lamps illuminate when the remote entrysystem is used to unlock the door(s).The illuminated entry syste

The remote start system will not work if:• The ignition is in the on position.• The alarm system is triggered.• The feature has been disabled.• The ho

The ignition switch must be turned to the on position and then back tothe off position or allow one hour to pass before using remote startagain.Turnin

Standard message centerNote: Some warning lights arereconfigurable telltale (RTT)indicator lights and will illuminate inthe message center. These ligh

5. The doors will again lock then unlock to confirm that your personalentry code has been programmed to the module.Tips:• Do not set a code that uses

SECURILOCK姞 PASSIVE ANTI-THEFT SYSTEM (IF EQUIPPED)SecuriLock威 passive anti-theft system is an engine immobilizationsystem. This system is designed to

Programming spare keysA maximum of eight keys can be coded to your vehicle. OnlySecuriLock威 keys can be used. To program a coded key yourself, youwill

6. To program additional new unprogrammed key(s), repeat Steps 1through 5.If successful, the new coded key(s) will start the vehicle’s engine.If not s

Disarming the systemYou can disarm the system by any of the following actions:• Unlock the doors by pressing thecontrol on your remote entrytransmitte

FRONT SEATSWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the eve

The adjustable head restraintsconsist of :• a trimmed energy absorbing foamand structure (1),• two steel stems (2),• a guide sleeve adjust/releasebutt

1. Insert the two stems (2) into theguide sleeve collars.2. Push the head restraint downuntil it locks.Properly adjust the head restraint so that the

Front row center non-adjustable head restraint (if equipped)Vehicle’s equipped with a front center seat will have head restraints thatare non-adjustab

WARNING: The non-adjustable head restraint is a safety device.It should be installed whenever the seat is occupied.WARNING: To minimize the risk of ne

WARNING: Under engine misfire conditions, excessive exhausttemperatures could damage the catalytic converter, the fuelsystem, interior floor coverings

20 percent front seat armrest and console (if equipped)To release the armrest and gainaccess to the cupholders andseatback storage bin, press thebutto

The under-seat storagecompartment (if equipped) has aprogrammable lock. Use the ignitionkey to program the lock to thecompartment. Electronics may bep

Power recline (if equipped)Press the control to recline theseatback forward or rearward.Using the power lumbar support (if equipped)The power lumbar c

Heated seatsWARNING: Persons who are unable to feel pain to the skinbecause of advanced age, chronic illness, diabetes, spinal cordinjury, medication,

Climate controlled seats air filter replacement (if equipped)The heated and cooled seat system includes air filters that must bereplaced periodically.

To install a filter:1. First, position the filter in itshousing making sure that the farforward end is all the way up in thehousing.2. Push in on the

Easy-access/easy-out feature (if equipped)The easy entry feature can be turned off or on through the vehiclemessage center. Refer to Message center in

Outboard head restraints (Crew Cab)Center head restraint (Crew Cab)The non-adjustable second row head restraints consist of :• a trimmed energy absorb

Folding up the rear seats (SuperCab)1. Pull control to release seatcushion.2. Rotate seat cushion up until itlocks into vertical storage position.Retu

Folding up the rear seat cushion1. Pull control to release seatcushion.2. Rotate seat cushion up until itlocks into vertical storage position.Returnin

WARNING: Driving a vehicle with the brake system warninglight on is dangerous. A significant decrease in brakingperformance may occur. It will take yo

Rear under seat storage (if equipped) (Crew Cab)The rear seat has storage space located under the seat cushion.Lift up the lever and flip up the seatc

SAFETY RESTRAINTSWARNING: Always drive and ride with your seatback uprightand the lap belt snug and low across the hips.WARNING: To reduce the risk of

WARNING: Safety belts and seats can become hot in a vehiclethat has been closed up in sunny weather; they could burn asmall child. Check seat covers a

Before you can reach and latch a combination lap and shoulder belt(with a cinch tongue) into the buckle, you may have to lengthen the lapbelt portion

While you are fastened in the safety belt, the combination lap/shoulderbelt with a cinch tongue adjusts to your movement. However, if youbrake hard, t

Automatic locking modeIn this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt

WARNING: BELT AND RETRACTOR ASSEMBLY MUST BEREPLACED if the safety belt assembly “automatic lockingretractor” feature or any other safety belt functio

Safety belt height adjustmentYour vehicle has safety belt heightadjustments at the front outboardseating positions. Adjust the heightof the shoulder b

Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition...The safety belt war

If... Then...The driver’s safety belt isbuckled before the ignitionswitch is turned to the onposition...The Belt-Minder威 feature will notactivate.The

Engine oil pressure (RTT andstatic warning light): Displayswhen the oil pressure falls below thenormal range. Refer to Engine oilin the Maintenance an

Reasons given... Consider...“The people I’m with don’twear belts”Set the example, teen deaths occur 4times more often in vehicles withTWO or MORE peop

WARNING: While the design allows you to deactivate yourBelt-Minder威, this system is designed to improve your chances ofbeing safely belted and survivi

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right

WARNING: Never place your arm over the airbag module as adeploying airbag can result in serious arm fractures or otherinjuries.To properly position yo

WARNING: An infant in a rear-facing seat faces a high risk ofserious or fatal injuries from a deploying passenger airbag. Rearfacing infant seats shou

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt

• one or more impact and safing sensors,• a readiness light and tone• and the electrical wiring which connects the components.The diagnostic module mo

How does the side airbag system work?The design and development of theside airbag system includedrecommended testing proceduresthat were developed by

to inflate in side-impact collisions, not roll-over, rear-impact, frontal ornear-frontal collisions, unless the collision causes sufficient lateraldec

WARNING: All occupants of the vehicle including the drivershould always wear their safety belts even when an airbag SRSand Safety Canopy威 System is pr

Transmission Tow/Haul Feature(if equipped): Displays when theTow/Haul feature has beenactivated. Refer to the Drivingchapter for transmission function

restrained using a properly installed child or booster seat because it isdesigned to inflate downward from the headliner above the doors alongthe side

A difficulty with the system is indicated by one or more of the following:• The readiness light (same light as for front airbag system) will eitherfla

Turning the passenger airbag off1. Insert the ignition key, turn theswitch to OFF position and hold inthe OFF position while removing thekey.2. When t

Turning the passenger airbag back onThe passenger airbag remains off until you turn it back on.1. Insert the ignition key and turnthe switch to ON.2.

WARNING: If your vehicle has rear seats, always transportchildren who are 12 and younger in the rear seat. Always usesafety belts and child restraints

2. Child age 1 to 12. A child age 1 to 12 must ride in the front seatbecause:• the vehicle has no rear seat;• although children ages 1 to 12 ride in t

2. Child age 12 or under: A child age 12 or under must ride in thefront seat because:• my vehicle has no rear seat;• although children age 12 and unde

SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag suppleme

Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfantsortoddlersChildren weighing 40 lb

• When possible, always properly restrain children twelve (12) years ofage and under in a rear seating position of your vehicle. Accidentstatistics su

Locks and Security 130Keys 130Locks 138Anti-theft system 151Seating and Safety Restraints 155Seating 155Safety restraints 171Airbags 182Child restrain

Electronic locking differential(RTT and static) (if equipped):Displays when using the electroniclocking differential.Speed control (if equipped): Thes

WARNING: Always carefully follow the instructions andwarnings provided by the manufacturer of any child restraint todetermine if the restraint device

Transporting childrenAlways make sure your child is secured properly in a device that isappropriate for their age, height and weight. All children are

SAFETY SEATS FOR CHILDRENInfant and/or toddler seatsUse a safety seat that is recommended for the size and weight of thechild.When installing a child

Installing child safety seats with automatic locking modecombination lap and shoulder belts (front passenger and rearoutboard seating positions)Check

Installing the child safety seatPerform the following steps when installing the child seat in theoutboard combination lap/shoulder belts:Note: Althoug

3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi

7. Try to pull the belt out of the retractor to make sure the retractor isin the automatic locking mode (you should not be able to pull more beltout).

Installing child safety seats in cinch tongue combination lap andshoulder belt seating positions (All front center and Super/Crewcab rear center posit

3. While holding both shoulder andlap portions next to the tongue,route the tongue and webbingthrough the child seat according tothe child seat manufa

6. Attach the tether strap (if the child seat is equipped). Refer toAttaching child safety seats with tether straps later in this chapter.7. Before pl

Key-in-ignition warning chime: Sounds when the key is left in theignition in the off or accessory position and the driver’s door is opened.Headlamps o

The tether anchors in your vehicle may be straps on the seatback or ananchor bracket mounted to the body shell on the back panel.The SuperCab rear sea

• F-Series Crew CabAttach the tether strap only to the appropriate tether anchor as shown.The tether strap may not work properly if attached somewhere

4. Remove tether cover.5. Clip the tether strap to the anchor as shown.• Front seats (Regular Cab)• Rear seats (Crew Cab)If the tether strap is clippe

6. Refer to the Installing child safety seats with automatic lockingmode combination lap and shoulder belts and Installing child safetyseats in cinch

2. Attach the strap hook onto theloop behind an adjacent seatingposition.3. Install the child safety seat tightlyusing the vehicle belts. Follow thein

Booster seats position a child so that vehicle lap/shoulder safety belts fitbetter. They lift the child up so that the lap belt rests low across the h

Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a

Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

2. Engine coolant temperature gauge: Indicates engine coolanttemperature. At normal operating temperature, the needle will be in thenormal range (betw

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary

• Narrower – to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUVs and

TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen

TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary

• Tread area of the tire: Area of the perimeter of the tire thatcontacts the road when mounted on the vehicle.• Rim: The metal support (wheel) for a t

Note: Do not reduce tire pressure to change the ride characteristics ofthe vehicle. If you do not maintain the inflation pressure at the levelsspecifi

3. Add enough air to reach the recommended air pressure.Note: If you overfill the tire, release air by pushing on the metal stem inthe center of the v

WARNING: An inflated tire and rim can be very dangerous ifimproperly used, serviced or maintained. To reduce the risk ofserious injury, never attempt

other signs of damage or excessive wear. If internal damage to the tire issuspected, have the tire demounted and inspected in case it needs to berepai

U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s

Odometer and trip odometer: The odometer is displayed on the lowerline in the message center and registers the total accumulated distancethe vehicle h

WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w

Safety PracticesWARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the tires; spinning the tires can tear the tire andcaus

The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear.Tire rotationRotating your tire

• Dual rear wheel (DRW) vehicles –Six tire rotationIf your vehicle is equipped with dualrear wheels it is recommended thatthe front and rear tires (in

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

7. H: Indicates the tire’s speed rating. The speed rating denotes thespeed at which a tire is designed to be driven for extended periods oftime under

9. M+S or M/S: Mud and Snow, orAT: All Terrain, orAS: All Season.10. Tire Ply Composition and Material Used: Indicates the number ofplies or the numbe

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS) (IF EQUIPPED)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe

XXX MILES (km) TO EThis displays an estimate of approximately how far you can drive withthe fuel remaining in your tank under normal driving condition

The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw

When your temporary spare tire is installedWhen one of your road tires needs to be replaced with the temporary spare,the TPMS will continue to identif

Low tirepressurewarning lightPossiblecauseCustomer action requiredFlashingwarning lightSpare tire inuseRepair the damaged road wheel/tireand reinstall

WARNING: To determine the required pressure(s) for yourvehicle, refer to the Safety Compliance Certification Label orTire Label located on the B-Pilla

3. Cycle the ignition to the onposition with the engine off.4. Turn the hazard flashers on thenoff three times. This must beaccomplished within 10 sec

7. Remove the valve cap from the valve stem on the right front tire;decrease the air pressure until the horn sounds.8. Remove the valve cap from the v

Follow these guidelines when using snow tires and chains:• If possible, avoid fully loading your vehicle.• Use only SAE Class S chains.• Install chain

Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

TIMERTimer displays the trip elapsed drive time.To operate, do the following:1. Press and release RESET in order to start the timer.2. Press and relea

• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

WARNING: Exceeding any vehicle weight rating limitation couldresult in serious damage to the vehicle and/or personal injury.Steps for determining the

to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12x 100) = 1400

Towing a trailer places an additional load on your vehicle’s engine,transmission, axle, brakes, tires and suspension. Inspect thesecomponents carefull

Vehicle type Rear axleratioMaximumGCWR - lb (kg)F–250/F–350 Single Rear Wheel (SRW) 3.73 19000 (8617)4.30 22000 (9977)F–350 Dual Rear Wheel (DRW) 3.73

WARNING: The hitch rating listed on the trailer hitch label aremaximum possible trailer ratings for that hitch but may not bewhat your vehicle is capa

Fifth-wheel and gooseneck towingYour vehicle may be equipped with a fifth-wheel prep package. Thispackage enables your vehicle to accept certain fifth

If you use a rental trailer, follow the instructions that the rental agencygives to you.Do not attach safety chains to the bumper.Trailer brakesElectr

The TBC user interface consists ofthe following:1. +/- (GAIN adjustmentbuttons): Pressing these buttonsadjusts the TBC’s power output tothe trailer br

8. TBC GAIN = XX.X (if equipped)9. FUEL LEVEL10. MYKEY DISTANCE (if MyKey威 is programmed)11. MYKEY(S) PROGRAMMED12. ADMIN KEYS PROGRAMMEDNote: Some sy

activated while the brake is also applied, the greater of the two inputsdetermines the power sent to the trailer brakes.• Stop lamps: Activating the T

Explanation of instrument cluster warning messages:The TBC interacts with the instrument cluster message center to displaythe following messages:TRAIL

• The TBC interacts with the brake system of the vehicle, includingABS, in order to reduce the likelihood of trailer wheel lock-up;therefore, if these

than the road tires on your vehicle, your spare tire is considered“temporary”. Consult information on the Tire Label or Safety ComplianceCertification

• The trailer brakes (including the shoes, drum and trailer brakemagnets) must be inspected and serviced at intervals specified by themanufacturer.• E

Note: Put your climate control system in recirculated air mode toprevent exhaust fumes from entering the vehicle. Refer to the ClimateControls chapter

Before using the recovery hooks:• Make sure all attaching points are secure and capable of withstandingthe applied load.• Never use chains, cables or

STARTINGPositions of the ignition1. Off— shuts off the engine and allaccessories/locks the steering wheeland allows key removal. Note: Inorder to swit

WARNING: Do not park, idle, or drive your vehicle in dry grassor other dry ground cover. The emission system heats up theengine compartment and exhaus

• Make sure the parking brake isset.• Make sure the gearshift is in P(Park).3. Turn the key to 3 (on) withoutturning the key to 4 (start).Some warning

AUTOUNLOCKThis feature automatically unlocks all vehicle doors when the driver’sdoor is opened within 10 minutes of the ignition being turned off.Pres

Note: Cranking may be stopped at any time by turning the key to the offposition.3. After idling for a few seconds, release the parking brake, apply th

2. When the engine starts, release the key, then gradually release theaccelerator pedal as the engine speeds up. If the engine still fails to start,re

Prior to using the engine block heater, follow these recommendations forproper and safe operation:• For your safety, use an outdoor extension cord tha

of power per hour. Your factory installed block heater system does nothave a thermostat; however, maximum temperature is attained afterapproximately t

application is detected, the system will remain activated as long as thebrake pedal is pressed or ABS is engaged. The system is deactivated byeither r

The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated until theparking brake is released.Pull the release lever to releas

four-wheel drive mode (if equipped), the traction control system will beautomatically disabled. Traction control operation will resume when thevehicle

ADVANCETRAC姞 WITH ROLL STABILITY CONTROL™ (RSC姞)STABILITY ENHANCEMENT SYSTEM(SINGLE REAR WHEEL (SRW) VEHICLES ONLY)The AdvanceTrac威 with RSC威 system p

WARNING: If a failure has been detected within theAdvanceTrac威 with RSC威 system, the stability control light willilluminate steadily. Verify that the

• If the driving condition is severe and your foot is not on the brake, thebrake pedal may move as the systems applies higher brake forces. Youmay als

Compass zone/calibration adjustment1. Determine your magnetic zone byreferring to the zone map.2. Turn ignition to the on position.3. Start the engine

Certain adverse driving maneuvers may activate the ESC system, whichinclude but are not limited to:• Taking a turn too fast• Maneuvering quickly to av

If you switch off the AdvanceTrac威 with RSC威 system, the stabilitycontrol off light will illuminate steadily. Pressing the stability controlbutton aga

Trailer sway controlYour vehicle may be equipped with trailer sway control. When properlyequipped, trailer sway control will use the vehicle’s Advance

WARNING: Hill descent control cannot control descent in allsurface conditions and circumstances, such as ice or extremelysteep grades. Hill descent co

Hill descent modes• At speeds below 20 mph (32 km/h): When the HDC switch is pressedand HDC is active, the HDC telltale will flash.• At speeds below 2

If any steering components are serviced or replaced, install newfasteners (many are coated with thread adhesive or have prevailingtorque features whic

For 2WD vehicles and vehiclesequipped with a manual shift4WD system:Turn the control to ON. Theindicator light will display in theinstrument cluster.O

WARNING: Vehicles with a higher center of gravity such asutility vehicles and trucks handle differently than vehicles with alower center of gravity. U

5. Remove the top half of the shroud.6. Remove the three fasteners underthe column that secure the lowershroud half to the column.7. Pull the lock lev

WARNING: If the parking brake is fully released, but the brakewarning lamp remains illuminated, the brakes may not beworking properly. See your author

RESET FOR REMOTE START (if equipped)Press RESET to enable remote start on or off and choose the remotestart duration time (5, 10, 15 minutes) and othe

R (Reverse)With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Re

WARNING: Do not use the tow/haul feature when driving in icyor slippery conditions as the increased engine braking can causethe rear wheels to slide a

to relearn the normal shift strategy parameters, much like having to resetyour radio stations when your vehicle battery has been disconnected.The adap

To activate tow/haul, press thebutton on the end of the gearshiftlever.The TOW HAUL indicator light willilluminate in the instrument cluster.Tow/haul

To return to normal D (Overdrive) position, move the shift lever backfrom M to D.• The transmission will operate in gears one through six.2 (Second)Us

All available gears will be displayed with the current gear indicated.Press the – button again to lock out gears beginning with the highestgear. Examp

this time, you have time to move your foot from the brake to theaccelerator pedal and pull away. The brakes are released automaticallyonce the engine

If Your Vehicle Gets Stuck in Mud or SnowNote: Do not rock the vehicle if the engine is not at normal operatingtemperature or damage to the transmissi

The RSS detects obstacles up to6 feet (2 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the fi

Keep the RSS sensors (located on the rear bumper/fascia) freefrom snow, ice and large accumulations of dirt (do not clean thesensors with sharp object

Customer Assistance 353Reporting safety defects (U.S. only) 360Reporting safety defects (Canada only) 360Cleaning 361Maintenance and Specifications 37

• Some messages will appear once and then again when the vehicle isrestarted.• Some messages will reappear after clearing or being reset if a problemo

• (1) Rear bumper• (2) Red zone• (3) Yellow zone• (4) Green zone• (5) Centerline of vehicleAlways use caution while backing.Objects in the red zone ar

WARNING: The camera system is a reverse aid supplementdevice that still requires the driver to use it in conjunction withthe rear view mirror and the

4WD operation is not recommended on dry pavement. Doing so couldresult in difficult disengagement of the transfer case, increased tire wearand decreas

• auto-manual hub locks can bemanually overridden by rotatingthe hub lock control from AUTOto LOCK if desired.• automatic operation of thehub locks is

2H (2WD) – For general on-road driving. Sends power to the rearwheels only should be used for street and highway driving. Providesoptimal smoothness a

Shifting from 4H (4x4 High) to 2H (2WD)Move the transfer case lever to 2H(2WD) at a stop or a vehicle speedbelow 3 mph (5 km/h).With the vehicle at co

3. Move the transfer case shift leverthrough N (Neutral) directly to 4H(4x4 High) or 2H (2WD).4. If the transfer case will notengage into 4H (4x4 High

4L (4X4 LOW) - Uses extra gearing to provide maximum power to allfour wheels at reduced speeds. Intended only for off-road applicationssuch as deep sa

Note: Some noise may be heard as the system shifts or engages; this isnormal.Note: 4x4 low mode is not intended for use on dry pavement.Driving off-ro

• Be extremely careful when driving on pavement made slippery byloose sand, water, gravel, snow or ice.If your vehicle goes off the edge of the paveme

FUEL LEVEL LOW — Displayed as a reminder of a low fuel condition.CHECK PARK AID (if equipped) — Displayed when the transmissionis in R (Reverse) and t

WARNING: Do not spin the wheels at over 35 mph (56 km/h).The tires may fail and injure a passenger or bystander.Refer to Gauges in the Instrument Clus

WARNING: Always set the parking brake fully and make surethe gearshift is latched in P (Park). Turn the ignition to the offposition and remove the key

Mud and waterIf you must drive through highwater, drive slowly. Traction orbrake capability may be limited.When driving through water,determine the de

Driving on hilly or sloping terrainAlthough natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should

Should you start to slide while driving on snowy or icy roads, turn thesteering wheel in the direction of the slide until you regain control.Avoid sud

Failure to maintain your vehicle properly may void the warranty, increaseyour repair cost, reduce vehicle performance and operational capabilitiesand

SNOWPLOWINGFord recommends that the Super Duty F-Series used for snow removalinclude the Snow Plow Package Option.Installing the snowplowWeight limits

Operating the vehicle with the snowplow attachedDo not use your vehicle for snow removal until it has been driven atleast 500 miles (800 km).The attac

Transmission operation while plowingOperate the vehicle with the automatic transmission gearshift lever inthe D (Overdrive) position and tow/haul off.

ROADSIDE ASSISTANCEVehicles sold in the U.S. : Getting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany off

INTKEY COULD NOT PROGRAM — Displayed when an attempt ismade to program a fifth integrated key to the remote keyless entrysystem. For more information

U.S. Ford vehicle customers who require Roadside Assistance, call1-800-241-3673.If you need to arrange roadside assistance for yourself, Ford MotorCom

FUEL PUMP SHUT-OFFIn the event of a moderate to severe collision, this vehicle is equippedwith a fuel pump shut-off feature that stops the flow of fue

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V

To remove the fuse panel cover, pullthe panel toward you. When theclips of the panel disengage, let thepanel fall easily.To remove a fuse use the fuse

The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingProtected Circuits1 30A Not used (spare)2 15A Upfitter relay #43 30A Not used (spare)4

Fuse/RelayLocationFuse AmpRatingProtected Circuits11 10A Instrument cluster12 15A Interior lighting, Lighted runningboard lamps13 15A Right turn signa

Fuse/RelayLocationFuse AmpRatingProtected Circuits31 5A Trailer brake controller (brakesignal), Customer access32 15A Moon roof, Telescoping mirrorswi

Power distribution boxThe power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that prot

Fuse/RelayLocationFuse AmpRatingProtected Circuits10 — Not used11 — Not used12 — Not used13 — Not used14 — Not used15 Diode Fuel pump (diesel engine)1

Fuse/RelayLocationFuse AmpRatingProtected Circuits38 Relay Powertrain control module(PCM) (diesel engine),Electronic control module (ECM)(gas engine)3

alarm system from triggering, the ignition must be turned to start or onbefore the 12 second chime expires. See Perimeter alarm system in theLocks and

Fuse/RelayLocationFuse AmpRatingProtected Circuits62 — Not used63 — Not used64 — Not used65 — Not used66 20A** Fuel pump67 — Not used68 10A** Fuel pum

Fuse/RelayLocationFuse AmpRatingProtected Circuits92 20A* Auxiliary power point #493 20A* Auxiliary power point #394 25A* Upfitter #195 25A* Upfitter

WARNING: The use of tire sealants may damage your tirepressure monitoring system (TPMS) and should not be used.However, if you must use a sealant, the

Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following:• Handling, stability and braki

Spare tire informationNote: If your vehicle is equipped the tire pressure monitoring system(TPMS), the system indicator light will illuminate when the

Tool LocationJack handle, lug wrench, lugwrench extension (only availableon Dual Rear Wheel [DRW]vehicles) and wheel chock (onlyavailable on Single Re

2. Attach the spare tire lock key (A)to the jack handle (B).3. Fully insert the jack handle (withone extension) through the bumperhole and into the gu

WARNING: To prevent the vehicle from moving when youchange a tire, be sure the parking brake is set, then block (inboth directions) the wheel that is

6. Position the jack according to the following guides:• Front (4x2)• Front driver side (4x4)Note: Make sure the jack fits ontothe flat area on the ou

• RearNever use the front or reardifferential as a jacking point.WARNING: To lessen therisk of personal injury, donot put any part of your bodyunder t

by doing the following: Turn the ignition on, without starting the engine.Press and release the brake pedal fully five times and press the hazardbutto

The following steps apply to F–350 Dual Rear Wheel (DRW) andF–450/F–550 vehicles only:11. Slide the notched end of thejack handle over the release val

• Front passenger side (4x4): F-350DRWNote: View shown from the rear ofthe vehicle to clearly identify thejack point.Note: Place the jack directly und

13. Insert the jack handle into thepump linkage.14. Use an up-and-down motionwith the jack handle to raise thewheel completely off the ground.Hydrauli

10–lug nut torque sequence19. Stow the flat tire. Refer to Stowing the flat/spare tire if the vehicleis equipped with a spare tire carrier.20. Stow th

If the ornament retention towers arealigned between the studs/lug nuts,the ornament is improperlyinstalled. This improper installationmay appear and s

4. Be sure to install all the clips on the nuts over the flanges so thatthere is an even gap all around and the retention clips are fully seated.Stowi

5. Turn the jack handle clockwise until the tire is raised to its stowedposition underneath the vehicle. The effort to turn the jack handleincreases s

On all two-piece flat wheel nuts,apply one drop of motor oil betweenthe flat washer and the nut.WARNING: When a wheel is installed, always remove anyc

JUMP STARTINGWARNING: The gases around the battery can explode ifexposed to flames, sparks, or lit cigarettes. An explosion couldresult in injury or v

Connecting the jumper cablesNote: In the illustration, the vehicle on the bottom is used to designatethe assisting (boosting) battery.1. Connect the p

TO EXIT 4X4 LOW SHIFT TO N (if equipped) — Displayed when2WD is selected while the vehicle has been stopped in 4X4 LOW. Formore information, refer to

Jump Starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

Note: Towing an ESOF 4x4 vehicle with the front wheels on the groundwithout disengaging the front hubs may cause damage to the automatictransmission.N

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehi

• Ford Genuine Accessories• Service specials and promotions.In Canada:Mailing addressCustomer Relationship CentreFord Motor Company of Canada, Limited

IN CALIFORNIA (U.S. ONLY)California Civil Code Section 1793.2(d) requires that, if a manufactureror its representative is unable to repair a motor veh

procedure outlined earlier in this chapter in the Getting the servicesyou need section, you may be eligible to participate in the BBB AUTOLINE program

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee

If your vehicle must be serviced while you are traveling or living inAsia-Pacific Region, Sub-Saharan Africa, U.S. Virgin Islands, CentralAmerica, the

If your vehicle must be serviced while you are traveling or living in theMiddle East, contact the nearest authorized dealer. If the authorizeddealer c

OK TO DRIVE (diesel engine only) — Displayed when the timecounter has reached 0 (zero) and the engine is sufficiently warm enoughto drive in extremely

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i

WAXING• Wash the vehicle first.• Use a quality wax that does not contain abrasives.• Do not allow paint sealant to come in contact with any non-body(l

• Do not spray a hot engine with cold water to avoid cracking theengine block or other engine components.• Spray Motorcraft威 Engine Shampoo and Degrea

• 6.8L V10 gasoline enginePLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft威 Premium Windshield Washer Concentrate (ZC-32-A) inthe U.S., or Premiu

3. If necessary, apply more soap and water solution or cleaning productto a clean, white, cotton cloth and press the cloth onto the soiledarea–allow t

INTERIORFor fabric, carpets, cloth seats and safety belts:• Remove dust and loose dirt with a vacuum cleaner.• Remove light stains and soil with Motor

LEATHER SEATS FOR THE KING RANCH姞 EDITION ONLY(IF EQUIPPED)Your vehicle is equipped with seating covered in premium, top-grainleather which is extreme

UNDERBODYFlush the complete underside of your vehicle frequently. Keep body anddoor drain holes free from packed dirt.Note: Use care when using a powe

CLEANING EXHAUST FILTER (diesel engine only) — Displayedwhen the vehicle has entered the cleaning mode. Various engine actionswill raise the exhaust t

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel.2. Go to the front of th

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENTRefer to the diesel supplement for diesel engine component locations.6.2L V8 gasoline engine1. Windshi

6.8L V10 gasoline engine1. Windshield washer fluid reservoir2. Battery3. Automatic transmission fluid dipstick4. Engine oil filler cap5. Engine oil di

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

Poor wiper quality can be improved by cleaning the wiper blades and thewindshield. Refer to Windows and wiper blades in the Cleaningchapter.To prolong

• Oil levels above the upper hole may cause engine damage. Some oilmust be removed from the engine by a service technician.7. Put the dipstick back in

To protect your engine and engine’s warranty, use Motorcraft威 SAE5W-20 or an equivalent SAE 5W-20 oil meeting Ford specificationWSS-M2C945-A. SAE 5W-2

If you see any corrosion on the battery or terminals, remove the cablesfrom the terminals and clean with a wire brush. You can neutralize theacid with

Because your vehicle’s engine is electronically controlled by a computer,some control conditions are maintained by power from the battery. Whenthe bat

REDUCED ENGINE POWER (diesel engine only) — Displayedapproximately two hours after the DRIVE TO CLEAN EXHAUSTSYSTEM message has displayed and the vehi

ENGINE COOLANTChecking engine coolantThe concentration and level of engine coolant should be checked at theintervals listed in scheduled maintenance i

Note: Automotive fluids are not interchangeable; do not use enginecoolant/antifreeze or windshield washer fluid outside of its specifiedfunction and v

• Do not add extra inhibitors or additives to the coolant. Thesecan be harmful and compromise the corrosion protection of the enginecoolant.For vehicl

If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your authorized dealer check the engine cooling system.Your coolin

If you drive in extremely hot climates:• It is still necessary to maintain the coolant concentrationabove 40%.• NEVER decrease the coolant concentrati

Once the engine temperature cools, the engine can be re-started. Takeyour vehicle to an authorized dealer as soon as possible to minimizeengine damage

WARNING: To reduce the risk of collision and injury, beprepared that the vehicle speed may reduce and the vehicle maynot be able to accelerate with fu

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELSImportant safety precautionsWARNING: Do not overfill the fuel tank. The pressure in anoverfilled tank may c

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek med

WARNING: Flexible fuel components and standard unleadedgasoline fuel components are not interchangeable. If your vehicleis not serviced in accordance

SPEED LIMITED XXMPH IN XXXMI EXHAUST FLUID SYSTEMFAULT (diesel engine only) — Displayed when the SCR systemdetects a fault. The vehicle’s top speed wi

Fuel filler capWhen fueling your vehicle:1. Turn the engine off.2. Carefully turn the filler cap counterclockwise until it spins off.3. Pull to remove

Your vehicle was not designed to use fuel or fuel additives with metalliccompounds, including manganese-based additives.Note: Use of any fuel other th

problems continue, fill the vehicle with regular unleaded gasoline anddrive vehicle normally until gasoline is used. See your authorized dealerif the

ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform

2. Each time you fill the tank, record the amount of fuel added (ingallons or liters).3. After at least three to five tank fill-ups, fill the fuel tan

• Warming up a vehicle on cold mornings is not required and mayreduce fuel economy.• Resting your foot on the brake pedal while driving may reduce fue

EMISSION CONTROL SYSTEMWARNING: Do not park, idle, or drive your vehicle in dry grassor other dry ground cover. The emission system heats up theengine

Do not make any unauthorized changes to your vehicle or engine. Bylaw, vehicle owners and anyone who manufactures, repairs, services,sells, leases, tr

Readiness for Inspection/Maintenance (I/M) testingSome state/provincial and local governments may haveInspection/Maintenance (I/M) programs to inspect

POWER STEERING FLUIDCheck the power steering fluid. Refer to scheduled maintenanceinformation. If adding fluid is necessary, use only MERCON威 ATF.• Ga

CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The

LOW FUEL PRESSURE SEE MANUAL (diesel engine only) —Ifthis message appears during a cold start or during cold operation 32°F(0°C) up to 10 minutes afte

BRAKE FLUID• Vacuum boost system• Hydroboost systemThe fluid level will drop slowly as the brakes wear, and will rise when thebrake components are rep

2. Park the vehicle on a level surface and engage the parking brake.3. With the engine running, parking brake engaged and your foot on thebrake pedal,

Correct fluid levelFor vehicles equipped with 5-speed transmissions, the fluid should bechecked at normal operating temperature 150°F-170°F (66°C-77°C

Adjusting automatic transmission fluid levelsBefore adding any fluid, make sure the correct type is used. The type offluid used is normally indicated

TRANSFER CASE FLUID (IF EQUIPPED)1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level.3. Add only enough fluid throughthe fil

The following procedure is for vehicles equipped with a gasoline engine.If your vehicle is equipped with a diesel engine, refer to the dieselsupplemen

5. Release the three clamps thatsecure the cover to the air filterhousing. Push the air filter covertoward the center of the vehicle andup slightly to

10. Reconnect the mass air flowsensor electrical connector to theoutlet tube. Make sure the lockingtab on the connector is in the“locked” position (co

• Keep all rubber parts free from oil and solvents.Engine• The engine oil and filter should be changed prior to storage, as usedengine oil contain con

• Move vehicles at least 25 feet (8 m) every 15 days to lubricateworking parts and prevent corrosion.Removing vehicle from storageWhen your vehicle is

Press the up/down buttons to moveup/down through the messagecenter choices.Press the left/right buttons to moveleft/right through the messagecenter ch

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem Capacity Ford part nameFord part number /Ford specificationFront axle 5.8 pints (2.8L)Motorcraft

Item Capacity Ford part nameFord part number /Ford specificationEngine and fuel coolant- diesel engineRefer to the diesel supplement.Engine oil (inclu

Item Capacity Ford part nameFord part number /Ford specificationHinges, latches, strikerplates, fuel filler doorhinge and seat tracks— Multi-Purpose G

Item Capacity Ford part nameFord part number /Ford specificationWindshield washer fluid Fill as requiredMotorcraft威 PremiumWindshield WasherConcentrat

ENGINE DATAEngine 6.2L V8 engine 6.8L V10 engineCubic inches 378 413Required fuelMinimum 87 octane orEthanol (E85)Minimum 87 octaneFiring order 1-5–4–

6.8L V10 engine - without A/CIDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulation

Vehicle identification number (VIN)The vehicle identification number islocated on the driver sideinstrument panel.Please note that in the graphic,XXXX

TRANSMISSION CODE DESIGNATIONSYou can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmis

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLEA wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of C

Peace of mind•Keyless entry keypad •Back up alarm*•Remote start •Cable lock*•Vehicle security systems •Bed hooks*•Wheel locks •Tool/Cargo boxes*•Prote

Gauge ModeIn this mode, the following options are available in different graphicalformats:• Engine Oil Temperature (diesel only)• Transmission Tempera

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY)More than 32 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the

Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With

Ford Extended Service Plan4222012 F-250/350/450/550 (f23)Owners Guide, 3rd PrintingUSA (fus)

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY)You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is

GENERAL MAINTENANCE INFORMATIONThe following information pertains to 6.2L V8 and 6.8L V10 gasolineengines only. Scheduled maintenance for the diesel e

Ford strongly recommends the use of genuine Ford replacement parts.Parts other than Ford, Motorcraft威 or Ford-authorized remanufacturedparts that are

Genuine Ford and Motorcraft姞 replacement partsDealerships stock Ford and Motorcraft威 branded replacement parts.These parts meet or exceed Ford Motor C

Check every monthEngine oil levelFunction of all interior and exterior lightsTires for wear and proper pressure, including spareWindshield washer flui

Multi-point inspection – Recommended each visitAccessory drive belt(s) Half-shaft dust boots (if equipped)Battery performance Horn operationClutch ope

NORMAL SCHEDULED MAINTENANCE AND LOGThe following section contains the “Normal Schedule”. This schedule ispresented at specific mileage (kilometer) in

If you calculate your average fuel economy by dividing miles traveled bygallons of fuel used (liters of fuel used by 100 kilometers traveled), yourfig

6.2L and 6.8L enginesMiles (x 1,000)* 7.5 15 22.5 30 37.5 45 52.5 60 67.5 75Kilometers (x 1,000)* 12 24 36 48 60 72 84 96 108 120Months* 6 12 18 24 30

6.2L and 6.8L enginesMiles (x 1,000)* 82.5 90 97.5 105 112.5 120 127.5 135 142.5 150Kilometers (x 1,000)* 132 144 156 168 180 192 204 216 228 240Month

6.2L and 6.8L enginesEvery 15,000 miles(24,000 km)Replace cabin air filter (if equipped)Every 30,000 miles(48,000 km)Replace climate-controlled seat f

Maintenance Schedule LogDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDAT

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

SPECIAL OPERATING CONDITIONSThe following information pertains to 6.2L V8 and 6.8L V10 gasolineengines only. Scheduled maintenance for the diesel engi

Extensive idling and/or low-speed driving for long distances asin heavy commercial use (i.e. delivery, taxi, patrol car or livery)Inspect frequently,s

Operating in dusty conditions such as unpaved or dusty roadsInspect frequently,service as requiredReplace cabin air filter (if equipped)Replace engine

Off-road operationInspect frequently,service as requiredInspect steering linkage, ball joints and U-joints;lubricate if equipped with grease fittingsR

Truck Apps (if equipped)In this mode, off-road and trailer towing application options are available.Off Road*Pitch and bank angle (in degrees). Displa

Special Operating Condition LogDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

EXCEPTIONSThere are several exceptions to the Normal Schedule. They are listedbelow:Normal vehicle axle maintenance: Rear axles and power take-off(PTO

Edge/MKX AWD only – vehicles operating off-road in sand during highambient temperatures must replace the AWD PTU (All-wheel drivePower Transfer Unit)

AAccessory delay ...106AdvanceTrac ...277Airbag supplemental restraintsystem ...1

LATCH ...209recommendations ...199Child safety seats - boosterseats ...

checking and adding ...375dipstick ...375filter, specifications ...376, 409recommendations ...

Inspection/maintenance (I/M)testing ...398Instrument panelcleaning ...365–366cluster ...

Parking brake ...274Parts (see Motorcraft威 parts)...409Pedals (see Power adjustablefoot pedals) ...

Snowplowing ...7, 316–317SOS Post Crash Alert ...191Spark plugs,specifications ...409, 414Special notice .

Trailer*Change ActiveTrailerWhen this is highlighted, press the right arrow key tochange the currently selected trailer. Use the up anddown arrows to

Washer fluid...374Water, Driving through...315Windowspower...104Windshield wa

SettingsIn this mode, you can configure different driver setting choices. Pressthe right arrow key (when in the Settings menu) to reach the DriverAssi

Vehicle* (cont’d)Locks Autolock, On/OffAutounlock On/OffUnlocking One Stage or Two StageMaintenance Coolant (ifequipped)Hold OK if coolant maintenance

System ResetHold OK to Reset System to Factory DefaultInformationIn this mode, you can view different vehicle system information andperform a system c

Compass/transmission indicator displaysThe compass heading will display in the upper right corner of themessage center; the transmission gear indicato

Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti

FUEL LEVEL LOW — Displayed as a reminder of a low fuel condition.BRAKE FLUID LEVEL LOW — Indicates the brake fluid level is lowand the brake system sh

WARNING: When the CLEANING EXHAUST FILTER messageappears in the message center, do not park near flammablematerials, vapors or structures until filter

ENGINE TURNS OFF IN 1 SECOND (diesel engine only) —Displayed when the vehicle is in the final second of a countdown towhere the engine will intentiona

EXHAUST FLUID RANGE XXX MI (diesel engine only) — Displaysthe distance you can travel before depleting the remaining diesel exhaustfluid. Refer to you

SPEED LIMITED TO 50 MPH EXHAUST FLUID SYSTEM FAULT(diesel engine only) — Displayed when the SCR system detects afault. The vehicle’s top speed is limi

• Normal Operation: If the message appears during normal operationwhen the vehicle / engine is fully warm, and fuel level is not low, thefuel filters

TRAIN INNER RIGHT REAR TIRE — Displayed when training theTPMS. Refer to TPMS reset procedure in the Tires, Wheels andLoading chapter for more informat

4X4 SHIFT IN PROGRESS (if equipped) — Displayed when the 4X4system is making a shift. For further information, refer to Four-wheeldrive (4WD) operatio

LOCKING DIFFERENTIAL DISENGAGED (if equipped) —Displayed when the electronic locking differential is disengaged. SeeElectronic locking differential in

CHECK SPEED DRIVE SAFELY — Displayed when a MyKey威 is inuse and the optional setting is on and the vehicle exceeds a preselectedspeed. Refer to MyKey威

Drive your new vehicle at least 1,000 miles (1,600 km) before towing atrailer. For more detailed information about towing a trailer, refer toTrailer t

REAR PARK AID OFF (if equipped) — Displayed when the rear parkaid is disabled by the driver.REAR PARK AID ON (if equipped) — Displayed when the rear p

AUDIO SYSTEMSAM/FM stereo system (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strong

1. / (Tuner): Press tomanually go up or down the radiofrequency. Press and hold for a fastadvance through radio frequencies.Also use in AUDIO mode to

6. ON/OFF/Volume: Press VOL -PUSH to turn ON/OFF. Turn VOL -PUSH to increase/decrease volume.7. CLK (Clock): Press CLK totoggle between the clock and

Accessory delay: Your vehicle is equipped with accessory delay whichallows you to operate the window switches and the audio for up to10 minutes after

• SAVE SONG: Press OK to save the currently playing song title in thesystem’s memory. (If you try to save something other than a song,CANT SAVE will a

When the six strongest stations are filled, the station stored in preset 1will begin playing. If there are less than six strong stations, the systemwi

COMPRESS (Compression): Available only in CD/MP3 mode. PressMENU until COMPRESS ON/OFF appears in the display.Use/ / SEEK, SEEK to toggle ON/OFF. When

7. SHUFFLE: In CD/MP3 mode,press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engage shuffle mode right away, p

13. TEXT/SCAN: In radio andCD/MP3 mode, press and hold fora brief sampling of radio stations orCD tracks. Press again to stop.In CD/MP3 mode, press an

Notice to owners of pickup trucks and utility type vehiclesWARNING: Utility vehicles have a significantly higher rolloverrate than other types of vehi

18. CD slot: Insert a CD label sideup in the CD slot.Auxiliary input jack (if equipped)WARNING: Driving while distracted can result in loss of vehicle

3. Attach one end of the audio extension cable to the headphone outputof your player and the other end of the audio extension cable to the AIJin your

USB port (if equipped)WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdriver

CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio for theselected channel.No action required. Thism

Radio Display Condition Action RequiredNO TEXT Category informationnot available.Category informationnot available at this timeon this channel. Thesys

SINGLE ZONE CLIMATE CONTROL1.Defrost: Distributes outside air through the windshield defrostervents and de-mister vents. Can be used to clear the wind

Using your vehicle as a stationary power source (PTO)Refer to the Driving chapter for more information and guidelines foroperating a vehicle equipped

5. Recirculated air (if equipped): Press to activate/deactivate airrecirculation in the vehicle. Recirculated air may reduce the amount oftime needed

• To improve the A/C cool down, drive with the windows slightly openfor 2-3 minutes after start up or until the vehicle has been “aired out.”• A small

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED)Temperature conversion: To switch between Fahrenheit and Celsius,refer to Optional or Standard mes

4. Manual control: Allows you to manually select where airflow isdirected. To return to full automatic control, press AUTO. Whenchoosing to control ai

9. Passenger heated seat (if equipped): Press to control thepassenger heated seat. Refer to Heated and cooled seats in the Seatingand Safety Restraint

• Do not put objects under the front seats that will interfere with theairflow to the back seats.• Remove any snow, ice or leaves from the air intake

REAR WINDOW DEFROSTER (IF EQUIPPED)RThe rear defroster control is located on the climate control panel andworks to defrost your rear window from fog a

For moderate weather conditions:• The interior cabin will be heated, cooled or off, based upon theprevious operating state (last ignition-on cycle).•

HEADLAMP CONTROLRotate the headlamp controlclockwise to the first position toturn on the parking lamps.Rotate clockwise to the secondpositionto also t

2. Turn the headlamp control to off.3. Turn the ignition switch to on and then back to off.4. Turn the headlamp control to the autolamp position. The

This data can help provide a better understanding of thecircumstances in which crashes and injuries occur.Note: EDR data is recorded by your vehicle o

Daytime running lamps (DRL) (if equipped)Turns the headlamps on with a reduced output.To activate:• the ignition must be in the on position,• the head

Vertical aim adjustmentThe headlamps on your vehicle can only be vertically adjusted. Yourvehicle does not require horizontal aim adjustments.To adjus

TURN SIGNAL CONTROLThe turn signal lever does not mechanically lock in the upward ordownward position when activated. The turn signal control activati

Rear dome/map lampsYour vehicle may have map lampswithin the rear dome lamp. Pressthe switches on either side of thedome lamp to turn the lamps on.BUL

Replacing exterior bulbsCheck the operation of all the bulbs frequently.Function Numberof bulbsTrade numberHeadlamps 2 H13/9008Park/Turn lamp 2 3157NA

Replacing headlamps, park lamps, turn lamps1. Make sure that the exterior lamps are off, then open the hood.2. Using masking tape or a marker,make an

10. For the headlamp bulb, removethe bulb by turning itcounterclockwise and pulling itstraight out.11. For the park or turn lamp bulb,remove the bulb

3. Rotate the bulb socket counterclockwise and remove from lampassembly.4. Pull the bulb straight out of the socket.Install the new bulb(s) in reverse

Replacing front clearance and identification lamp bulbs(if equipped)1. Make sure the headlamps are off.2. Remove the screw and lens fromthe lamp assem

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the