Introduction 4Instrument Cluster 10Warning lights and chimes 10Gauges 15Entertainment Systems 18AM/FM stereo 18AM/FM stereo with CD 20AM/FM stereo cas
WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may
To adjust the front seatback usingthe manual recliner:• Lift and hold the handle locatedon the side of the seat.• Lean against the seatback toadjust i
To reduce the risk of possible serious injury: Do not hang objectsoff seat back or stow objects in map pocket (if equipped) whena child is in the fron
Press to move the front portion ofthe seat cushion up or down.Press to move the rear portion ofthe seat cushion up or down.Using the power lumbar supp
• Push the indicated side of thecontrol for minimum heat.• Push again to deactivate.The heated seat module resets at every ignition run cycle. While t
• Front safety belts with pretensioners, energy management retractors,and safety belt usage sensors• Driver’s seat position sensor• Front crash severi
allows your Personal Safety System娂 to distinguish between differentlevels of crash severity and modify the deployment strategy of thedual-stage airba
will light and stay lit to remind you that the front passenger frontalairbag is off. See Front passenger sensing system in the airbags sectionof this
• A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and warning light are repaired.If any of these thin
Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints.Safety belts and seats can becom
Lap beltsAdjusting the front center seat lap belt (if equipped)The lap belt should fit snugly and as low as possible around thehips, not across the wa
Check engine: The Check engineindicator light illuminates when theignition is first turned to the ONposition to check the bulb and toindicate whether
Webbing extraction sensitive modeThe webbing sensitive locking mode locks the webbing and preventsmore belt from being pulled out if the belt is pulle
• Grasp the shoulder portion andpull downward until the entirebelt is pulled out.• Allow the belt to retract. As the belt retracts, you will hear a cl
Front safety belt height adjustmentYour vehicle has safety belt heightadjustments for the driver and frontoutboard passenger. Adjust theheight of the
Safety belt warning light and indicator chimeThe safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occup
If... Then...The driver’s and front passenger’ssafety belts are buckled before theignition switch is turned to the ONposition or less than 1-2 minutes
Reasons given... Consider...“Belts areuncomfortable”We design our safety belts to enhance comfort. Ifyou are uncomfortable - try different positions f
One time disableIf at any time the driver/front passenger quickly buckles then unbucklesthe safety belt for that seating position, the Belt-Minder威 is
3. For the seating position being disabled, at a moderate speed, bucklethen unbuckle the safety belt 9 times, ending in the unbuckled state.(Step 3 mu
Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in
To properly position yourself away from the airbag:• Move your seat to the rear as far as you can while still reaching thepedals comfortably.• Recline
Brake system warning light: Toconfirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the ON
Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear
The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt
The diagnostic module monitors its own internal circuits as well as thesupplemental airbag electrical system wiring (including the impactsensors), the
For side airbag equipped vehicles, the front passenger sensing systemwill turn off the passenger seat side airbag if:• the seat is empty and safety be
• Restart the vehicle and have the person remain in this position forabout two minutes. This will allow the system to detect that personand enable the
ObjectsPass Airbag OffIndicator LampPassengerAirbagSmall (i.e. 3 ring binder,small purse, bottled water)Unlit DisabledMedium (i.e. heavy briefcase,ful
In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit.If the airbag readi
Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref
All occupants of the vehicle should always wear their safety beltseven when an airbag SRS is provided.How does the side airbag system work?The design
to inflate in side-impact collisions, not roll-over, rear-impact, frontal ornear-frontal collisions, unless the collision causes sufficient lateraldec
Charging system: Illuminates whenthe battery is not charging properly.Engine oil pressure: Illuminateswhen the oil pressure falls below thenormal rang
SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag suppleme
belt will provide some protection, these children are still too small forlap/shoulder belts to fit properly, which could increase the risk of seriousi
Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi
Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the sto
Never use pillows, books, or towels to boost a child. They canslide around and increase the likelihood of injury or death in acollision.SAFETY SEATS F
Ford recommends the use of a child safety seat having a top tetherstrap. Install the child safety seat in a seating position with LATCH andtether anch
1. Position the child safety seat in aseat with a combination lap andshoulder belt.2. Pull down on the shoulder beltand then grasp the shoulder beltan
4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear
8. Allow the safety belt to retract toremove any slack in the belt.9. Before placing the child in theseat, forcibly move the seat forwardand back to m
2. Route the child safety seat tether strap over the back of the seat.For vehicles with adjustable head restraints, route the tether strap underthe he
Low fuel (if equipped):Illuminates when the fuel level inthe fuel tank is at or near empty(refer to Fuel gauge in this chapterfor more information).O/
Attaching safety seats with LATCH (Lower Anchors and Tethers forChildren) attachmentsSome child safety seats have two rigid or webbing mounted attachm
If you install a child seat with rigid LATCH attachments, do not tightenthe tether strap enough to lift the child seat off the vehicle seat cushionwhe
INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade
The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o
Increasing the inflation pressure beyond this pressure will not increasethe tire’s load carrying capability.• kPa: Kilopascal, a metric unit of air pr
Under-inflation is the most common cause of tire failures andmay result in severe tire cracking, tread separation or ⬙blowout⬙,with unexpected loss of
Note: If you have to drive a distance to get air for your tire(s), checkand record the tire pressure first and add the appropriate air pressurewhen yo
Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them
U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s
When mounting replacement tires and wheels, you should notexceed the maximum pressure indicated on the sidewall of thetire to set the beads without ad
GAUGESSpeedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge: Indicates engine coolanttemperature. At normal operatingtempera
Highway hazardsNo matter how carefully you drive there’s always the possibility that youmay eventually have a flat tire on the highway. Drive slowly t
• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can
Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (
Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/
11. Maximum Load: Indicates the maximum load in kilograms andpounds that can be carried by the tire. Refer to the Safety ComplianceCertification Label
Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;
Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8
SNOW TIRES AND CHAINSSnow tires must be the same size and grade as the tires youcurrently have on your vehicle.The tires on your vehicle have all weat
Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab
Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load
Odometer: Registers the total miles (kilometers) of the vehicle.• Without Message CenterTo switch the display from Metric toEnglish, press and hold th
GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S
GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)
Steps for determining the correct load limit:1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.
calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 -540 = -103 kg. You will need to reduce the load weight by at least240 lb. (104
Safety chainsAlways connect the trailer’s safety chains to the frame or hook retainersof the vehicle hitch. To connect the trailer’s safety chains, cr
• Anticipate stops and brake gradually.• Do not exceed the GCWR rating or transmission damage may occur.Servicing after towingIf you tow a trailer for
• do not allow waves to break higher than 6 inches (15 cm) above thebottom edge of the rear bumper.Exceeding these limits may allow water to enter veh
STARTINGPositions of the ignition1. OFF/LOCK, shuts off the engineand all accessories/locks thegearshift lever and allows keyremoval.2. ACC, allows th
If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smellexhaust fumes.Important saf
5. Turn the key to 3 (ON) withoutturning the key to 4 (START).Some warning lights will briefly illuminate. See Warning lights andchimes in the Instrum
Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel tank (when the ignitionis in the ON position). The fuelgauge may vary slightly whe
Do not use starting fluid such as ether in the air intake system. Suchfluid could cause immediate explosive damage to the engine and possiblepersonal
ENGINE BLOCK HEATER (IF EQUIPPED)To reduce the risk of electrical shock, do not use your heaterwith ungrounded electrical systems or two-pronged (chea
Anti-lock brake system (ABS)This vehicle is equipped with an anti-lock braking system (ABS). A noisefrom the hydraulic pump motor and pulsation in the
With the ABS light on, the anti-lockbrake system is disabled and normalbraking is still effective unless thebrake warning light also remainsilluminate
If the parking brake fails to releaseafter completing this procedure, usethe manual parking brake releaselever.Pull the lever to manually releasethe p
During Traction Control娂 operation you may hear an electric motor typeof sound coming from the engine compartment and the engine will not“rev-up” when
It is also important to maintain a proper power steering fluid level in thepower steering fluid reservoir:• Do not operate the vehicle with a low powe
This system keeps the rear of your vehicle at a constant level byautomatically adding air or releasing air from the springs.If you exceed the load lim
2. Locate the access plug on theunderside of the steering columncover.3. Remove the access plug using a flat head screwdriver. Insert thescrewdriver i
2. Insert the key and turn it to ACC. Apply the brake pedal and shiftto N (Neutral).When the key is in the ignition and in the ACC position, theautoma
AUDIO SYSTEMSAM/FM stereo (if equipped)1. Seek: Press/ to find thenext strong station down/up thefrequency band.2. Tune: Press/ to manuallychange radi
• Depress the brake pedal• Move the gearshift lever into the desired gearTo put your vehicle in P (Park):• Come to a complete stop• Move the gearshift
If your vehicle is equipped with afloor-shift transmission, overdrivecan be deactivated by pressing thetransmission control switch on thegearshift han
1 (First)• Provides maximum engine braking.• Allows upshifts by moving gearshift lever.• Will not downshift into 1 (First) at high speeds; allows for
ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside
• towing of your disabled vehicle• emergency travel expense reimbursement• travel planning benefitsUsing roadside assistanceComplete the roadside assi
• The hazard lights control islocated on top of the steeringcolumn.• Depress hazard lights control toactivate all hazard flasherssimultaneously.• Depr
3. If no fuel leak is apparent, reset the fuel pump shut-off switch bypushing in on the reset button.4. Turn the ignition to the ON position. Pause fo
COLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge50A — — Red Red Red60A — — Blue Yellow Yellow70A — — Tan — Brown80A
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 10A Ignition (START) - Starter relaycoil, DTRS2 7.5A Power mirrors, Door
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description13 10A Ignition (ON) - Anti-lock BrakeSystem (ABS) module, Rear AirSuspensi
5. Power/volume: Press to turnON/OFF; turn to increase ordecrease volume levels.6. Tone: Press TONE until thedesired level — Bass, Treble, Fadeappears
Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description24 10A Ignition (ON/START) - PassiveAnti-Theft System (PATS)module, Powertr
The high-current fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription1 30A* Ignition switch2 20A* Moon roof, S
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription12 20A* Audio (Subwoofer)25A* Tray lamps (Police vehicles only)13 20A* Instrument pan
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription108 20A** Police accessory battery feed 3(Police vehicles only)109 20A** ABS module (
Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription208 — Not used2091⁄2ISO relay Horn301 Full ISO relay Starter302 Full ISO relay Air co
and tread design. If this is the case, this dissimilar spare tire is still ratedfor your vehicle loads (GAWR and GVWR).The use of tire sealants may da
Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following:• Handling, stability and braki
Full-size Matching Spare Tire/Wheel InformationThis spare tire/wheel will match the road tire/wheel. When driving withthe full size matching spare tir
3. Remove the spare tire and thejack. The jack could be located:• A — behind the mini spare tire or• B — behind the full size sparetireOn vehicles equ
5. Locate pry off notch (ifequipped) and remove the centerornament from the aluminum wheelwith the tapered end of the wheelnut wrench that came with y
Seating and Safety Restraints 98Seating 98Safety restraints 103Airbags 117Child restraints 130Tires, Wheels and Loading 142Tire information 142Vehicle
AM/FM Stereo Single CD Premium audio system (if equipped)1. CD slot: Insert a CD, label sideup. With the ignition on, the radiowill begin play when a
To lessen risk of personalinjury, do not put any partof your body under the vehiclewhile changing a tire. Do not startthe engine when your vehicle iso
Bolt size Wheel lug nut torque*lb.ft. N•m1⁄2x 20 100 135* Torque specifications are for nut and bolt threads free of dirt andrust. Use only Ford recom
3. Park the booster vehicle close to the hood of the disabled vehiclemaking sure the two vehicles do not touch. Set the parking brake onboth vehicles
3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery.4. Make the final connection of the negative (-) cable to an ex
3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables.Removing the jum
3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of
WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y
GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling
In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo
In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a
5. Eject: Press to eject the CD. Ifthe disc is not removed within theallotted time, the system willautomatically reload the CD and begin play. Note: T
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY)Your satisfaction is important to Ford Motor Company and to your dealer.Experience has sh
UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to fee
If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformatio
ORDERING ADDITIONAL OWNER’S LITERATURETo order the publications in this portfolio, contact Helm, Incorporated at:HELM, INCORPORATEDP.O. Box 07150Detro
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov;or write to:
WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is
WAXINGApplying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage.• Wash the ve
ENGINEEngines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing:• Take care when
• If tar or grease spots are present, use Motorcraft Bug and TarRemover (ZC-42).• For plastic headlamp lenses, use Motorcraft Ultra Clear Spray GlassC
cotton cloth; you may also use Motorcraft Dash & Vinyl Cleaner(ZC-38-A) on the instrument panel and interior trim areas.• Avoid cleaners or polish
When activated, AUTOSET will momentarily appear in the display whenany of the preset controls are pressed.Speed sensitive volume: Radio volume changes
• Do not use household cleaning products or glass cleaners, which canstain and discolor the fabric and affect the flame retardant abilities ofthe seat
Motorcraft Bug and Tar Remover (ZC-42)Motorcraft Car Care Kit (ZC-26)Motorcraft Car Wash (Canada only) (CXC-21)Motorcraft Custom Bright Metal Cleaner
SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your
OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under theinstrument panel.2. Go to the front of the vehicle andrelease the
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT4.6L SOHC V8 engine1. Brake fluid reservoir2. Engine oil dipstick3. Windshield washer fluid reservoir4
WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer
Poor wiper quality can be improved by cleaning the wiper blades and thewindshield, refer to Windows and wiper blades in the Cleaningchapter.To prolong
• If the oil level is within thisrange, the oil level is acceptable.DO NOT ADD OIL.• If the oil level is below thismark, engine oil must be addedto ra
To avoid possible oil loss, DO NOT operate the vehicle with theengine oil level indicator and/or the engine oil filler cap removed.Engine oil and filt
BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.If
16. SCAN: Press SCAN to hear abrief sampling of radio stations orCD tracks. Press again to stop.Premium/Audiophile Satellite Compatible AM/FM Stereo S
Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyeswhen working near
• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin
When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “FULL COLD” level or within the“CO
Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn youbadly. Also, you can be bur
coolant degas system with a pressurized cap, or if it is necessary toremove the coolant pressure relief cap on the radiator of a vehicle withan overfl
Recycled engine coolantFord Motor Company does NOT recommend the use of recycled enginecoolant in vehicles originally equipped with Motorcraft Premium
• Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperatures i
1. Pull off the road as soon as safely possible and turn off the engine.2. Arrange for the vehicle to be taken to an authorized dealer.3. If this is n
Automotive fuels can cause serious injury or death if misused ormishandled.Fuel ethanol and gasoline may contain benzene, which is acancer-causing age
“Fuel Ethanol ”. To identify if your vehicle is an FFV, it may beequipped with a yellow fuel cap with the writing “E85/Gasoline”, orcheck if there is
3. BASS: Press BASS; thenpressSEL-TEXT todecrease/increase the level of bassoutput.TREB (Treble): Press TREB; thenpressSEL-TEXT todecrease/increase th
The flow of fuel through a fuel pump nozzle can produce staticelectricity, which can cause a fire if fuel is pumped into anungrounded fuel container.R
5. Turn the filler cap clockwise 1/4 of a turn until it clicks at least once.If the Check Fuel Cap indicator or message comes on and stays on afteryou
The use of leaded fuel is prohibited by law and could damage yourvehicle.Your vehicle was not designed to use fuel or fuel additives with metalliccomp
performance and emission control system protection for your vehicle.Gasolines that meet the World-Wide Fuel Charter should be used whenavailable. Ask
• The indicator may come on. For more information on the “checkengine” or the “service engine soon” indicator, refer to Warning lightsand chimes in th
• Have the vehicle loading and distribution the same every time.Your results will be most accurate if your filling method is consistent.Calculating fu
• Revving the engine before turning it off may reduce fuel economy.• Using the air conditioner or defroster may reduce fuel economy.• You may want to
EPA window stickerEvery new vehicle should have the EPA window sticker. Contact yourauthorized dealer if the window sticker is not supplied with your
Exhaust leaks may result in entry of harmful and potentiallylethal fumes into the passenger compartment.Do not make any unauthorized changes to your v
OBD-II may not have symptoms that are apparent, continued drivingwith theindicator on can result in increased emissions, lower fueleconomy, reduced en
stations are independently operated and individually elect to use RDStechnology to transmit station ID and program type as desired.FIND Program type:
POWER STEERING FLUIDCheck the power steering fluid.Refer to scheduled maintenanceinformation for the service intervalschedules.1. Start the engine and
BRAKE FLUIDThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels below the “MAX” lineth
Low fluid levelDo not drive the vehicle if the fluidlevel is at the bottom of the dipstickand the ambient temperature isabove 50°F (10°C).Correct flui
Use of a non-approved automatic transmission fluid may causeinternal transmission component damage.If necessary, add fluid in 1/2 pint (250 ml) increm
5. Install a new air filter element. Becareful not to crimp the filterelement edges between the air filterhousing and cover. This could causefilter da
equivalent replacement part. The customer warranty may be voidfor any damage to the emissions system if such a PCV valve is notused.2For spark plug re
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem Capacity Ford part nameFord part number /Ford specificationBrake fluidBetween MIN andMAX on rese
Item Capacity Ford part nameFord part number /Ford specificationPower steering fluidFill to line onreservoirMotorcraft MERCON威 VATFXT-5-QM /MERCON威 VA
4Automatic transmissions that require MERCON威 V should only use MERCON威 V fluid or fluid thatis specified dual usage MERCON威/MERCON威 V. Refer to sched
ENGINE DATAEngine 4.6L V8 engine 4.6L FFV V8 engineCubic inches 281 281Required fuel 87 octane 87 octane or Ethanol(E 85)Firing order 1-3-7-2-6-5-4-8
Dolby: Works in tape mode to reduces tape noise and hiss. Press MENUuntil DOLBY XX appears in the display. PressSEL-TEXT totoggle ON/OFF.The Dolby威 no
IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli
The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating
GENUINE FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of
For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle:• When adding accessories,
AABS (see Brakes) ...172Air cleaner filter ...253–254Air conditioning ...35Air suspension ...
washing ...215waxing ...216wheels ...216wiper bl
Exhaust fumes ...170FFail safe cooling ...236Flexible Fuel Vehicle (FFV) ...237Floor mats ...
autolock ...83keypad ...90programming entry code ...90Keys ...
Relays ...186, 194Remote entry system ...86, 90illuminated entry ...89locking/unlocking doors
wrecker ...206Traction control ...174Traction-lok rear axle ...177Transmission ...
13. SCAN: Press SCAN to hear abrief sampling of radio stations,selections or CD tracks. Press againto stop.14. SHUF (Shuffle): Press to playthe tracks
270
271
272
Audiophile AM/FM Satellite Compatible Stereo In-dash Six CDsound system (if equipped)1. CD slot: To insert a CD, pressLOAD. When the system is ready,i
4. MUTE: Press to mute the playingmedia. Press again to return to theplaying media or turn the volumecontrol to adjust the volume.5. Eject: Press to e
Maintenance and Specifications 222Engine compartment 224Engine oil 226Battery 229Engine coolant 231Fuel information 237Air filter(s) 253Part numbers 2
9. MENU: Press MENU repeatedlyto access RDS on/off.UseSEL-TEXT to toggleRDS on/off. Press MENU again to access Program type mode or ShowType mode. (ME
Speed sensitive volume: Radio volume changes automatically andslightly with vehicle speed to compensate for road and wind noise.Recommended level is 1
16. SHUF (Shuffle) /SCAN: Press SCAN to hear a brief sampling ofradio stations or CD tracks on the current CD. Press again to stop.SHUF (Shuffle): Pre
CD/CD player care:Do:• Handle discs by their edges only. Never touch the playing surface.• Inspect discs before playing. Clean only with an approved C
MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature sele
To aid in side window defogging/demisting in cold weather:1. Select NORM A/C.2. Adjust the temperature control to maintain comfort.3. Set the fan spee
3. Fan speed: Turn to manuallyincrease or decrease fan speed.4. Defrost:Distributes outside air through the windshield defrostervents and the side win
• Remove any snow, ice or leaves from the air intake area at the base ofthe windshield.To aid in side window defogging/demisting in cold weather:1. Se
HEADLAMP CONTROLTurns the lamps off.Turns on the parkinglamps, instrument panel lamps,license plate lamps and tail lamps.Turns the headlamps on.Autola
5. At the desired autolamp time delay, place the headlamp switch in theOFF position.• At this point, the exterior lamps turn off and the time delay is
CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth
PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel during headlampand parklamp operation.• Rotate the thumbwheel from leftto righ
INTERIOR LAMPSMap/Courtesy lampsThe courtesy lamps light when:• any door is opened.• the instrument panel dimmerswitch is rotated past the detent.• th
Rear courtesy/reading lampsRotate the lens to illuminate thelamp. With the lens in the flatposition, the courtesy lamp lightswhen:• Any door is opened
Function Trade NumberRear reading lamp 578Map lamp 906Dual floorwell lamp 906Glove compartment 168Visor vanity lamp - Slide on Rail system(SOR)37All r
3. Remove two retainers and pullheadlamp assembly forward toexpose bulb.4. Disconnect the electricalconnector from the bulb by pullingrearward.5. Remo
right to align the grooves in the plastic base with the tabs in the lampassembly. When the grooves are aligned, push the bulb into the lampassembly un
Replacing front side marker bulbTo remove the front side marker bulb:1. Make sure headlamp switch is in the OFF position, then open thehood.2. Remove
1. Make sure headlamp switch is inOFF position, then open the trunkand remove the pin-type retainerand carefully pull the carpet away toexpose the lam
ensuring the grommets are pushed all the way into the trunk lid andsecure with two screws.Replacing backup lamp bulbs1. Open trunk and remove bulbsock
MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the
SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury to yourself or others? Inthis guide, answ
TILT STEERING WHEELTo adjust the steering wheel:1. Pull and hold the steering wheelrelease control toward you.2. Move the steering wheel up ordown unt
CENTER CONSOLE (IF EQUIPPED)Your vehicle may be equipped with a variety of console features. Theseinclude:• Utility compartment• Power point (inside s
3. Press and hold the MODE controluntil VAR appears in the display,then release. The display shouldshow the current zone number.4. Press the MODE cont
3. From a blank display press andrelease the MODE button once. Thedirectional heading will bedisplayed.Note: If the compass isde-calibrated, CAL will
4. Determine which magnetic zoneyou are in by referring to the zonemap.5. Repeatedly press and release theRESET button to scroll through thezones 1–15
4. Press the RESET button tode-calibrate the compass. Thedisplay will read CIRCLE SLOWLYTO CALIBRATE for a few secondsand then display a direction wit
ProgrammingDo not program the HomeLink威 with the vehicle parked in thegarage.Note: Some vehicles may require the ignition switch to be turned to these
3. Simultaneously press and holdboth the HomeLink威 and hand-heldtransmitter button. The messageCHANNEL “X” (1,2 or 3) TRAININGwill appear on the displ
If the indicator light(s) underneath the house icon blink rapidly for twoseconds and then turn to a continuous light, proceed with steps 6through 8 to
Operating the HomeLink姞 Wireless Control SystemTo operate, simply press and release the appropriate HomeLink威 button.Activation will now occur for the
Notice to owners of Severe Duty vehiclesBefore you drive your vehicle, be sure to read the Severe Duty Owner’sGuide supplement. This book contains imp
Reprogramming a single HomeLink姞 buttonTo program a device to HomeLink威 using a HomeLink威 button previouslytrained, follow these steps:1. Press and ho
To prevent the battery from being discharged, do not use the powerpoint longer than necessary when the engine is not running.Always keep the power poi
One touch downAllows the driver’s window to openfully without holding the controldown. Press completely down onthe bottom part of the rocker switchand
EXTERIOR MIRRORSPower side view mirrorsTo adjust your mirrors:1. Select to adjust the leftmirror orto adjust the rightmirror.2. Move the control in th
POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED)The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is
3. Press the SET + control andrelease it.4. Take your foot off the acceleratorpedal.5. The indicatorlight (ifequipped) on the instrument clusterwill t
Increasing speed while using speed controlThere are two ways to set a higherspeed:• Press and hold the SET + controluntil you get to the desiredspeed,
Turning off speed controlThere are two ways to turn off the speed control:• Depress the brake pedal. This willnot erase your vehicle’spreviously set s
Climate control features• Press TEMP + or - to adjusttemperature.MOON ROOF (IF EQUIPPED)Do not let children play with the moon roof or leave childrenu
HOMELINK姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED)The HomeLink威 Wireless Control System, located on the overheadconsole, provides a convenient way to rep
To access this information, special equipment must be directly connectedto the recording modules. Ford Motor Company and Ford of Canada donot access e
1. Press and hold the two outsidebuttons releasing only when theindicator light begins to flash after20 seconds. Do not repeat Step 1to program additi
6. Firmly press and release the “learn” or “smart” button. (The name andcolor of the button may vary by manufacturer.)Note: There are 30 seconds in wh
Operating the HomeLink姞 Wireless Control SystemTo operate, simply press and releasethe appropriate HomeLink威 button.Activation will now occur for thet
MESSAGE CENTER (IF EQUIPPED)With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle info
ResetPress this control to reset functions shown in the INFO menu andSETUP menu.Info menuThis control displays the following control displays:• Trip o
Average fuel economy (AFE)Select this function from the INFOmenu to display your average fueleconomy in miles/gallon orliters/100 km.If you calculate
Trip elapsed drive timeSelect this function from the INFOmenu to display a timer.To operate the Trip Elapsed DriveTime perform the following:1. Press
The sequence of the system check report and how it appears in themessage center is as follows:1. OIL LIFE— PRESS RESET IF NEW OIL2. WASHER FLUID3. AIR
Language1. Select this function from theSETUP menu for the currentlanguage to be displayed.2. Pressing the SELECT controlcycles the message center thr
• They will not reappear until an ignition OFF-ON cycle has beencompleted.This acts as a reminder that these warning conditions still exist withinthe
These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag
LOW FUEL. Displayed as an early reminder of a low fuel condition.Warning message can be reset by pressing the RESET button, but willreturn after 10 mi
2. Press and hold the RESETcontrol for 3 seconds and release.Oil life is set to 100% and “OIL LIFESTART VALUE SET TO XXX%” isdisplayed.POSITIVE RETENT
KEYSThe vehicle is equipped with a master (black) key and valet (gray) keylock system (if equipped with valet feature).• The master key will access th
The vehicle may still be locked with the key in the ignition, andperforming one of the following actions:• Pressing the manual lock button on the door
wait at least 30 seconds. Note: Before following the procedure, makesure that the ignition is in the 1 (OFF/LOCK) position and all vehicledoors, the h
CHILDPROOF DOOR LOCKSWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoo
Keep vehicle doors andluggage compartmentlocked and keep keys and remotetransmitters out of a child’s reach.Unsupervised children could lockthemselves
Unlocking the doors1. Press and release to unlock the driver’s door. Note: The interiorlamps will illuminate.2. Pressand release again within five sec
To replace the battery:1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIR
• Perform the following programming procedure yourself:Note: Ensure the brake pedal is notdepressed during this sequence.Place the key in the ignition
Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng
The inside lights will not turn off if:• they have been turned on with the dimmer control, or• any door is open.The battery saver will shut off the in
To create your own personal entry code:1. Enter the factory set code. Note: The keypad will illuminate whenpressed.2. Within five seconds press 1 • 2
Erasing personal codeTo erase all of the personal entry codes programmed to a vehicle:1. Enter the factory-set code.2. Press and release 1 • 2 within
This device complies with part 15 of the FCC rules and with RSS-210 ofIndustry Canada. Operation is subject to the following two conditions:(1) This d
Immobiliser System PATS XCVR certification numbersTunisia 269/MAT/2004United Arabian Emirates 5/10-2/3274/3774Uruguay 025/FR/2003USA NT8-15607PAT3XCVR
Automatic armingThe vehicle is armed immediatelyafter switching the ignition to the 1(OFF/LOCK) position.The theft indicator on theinstrument panel wi
1. Insert the first previouslyprogrammed coded key into theignition and turn the ignition from 1(OFF/LOCK) to the 3 (ON) position(maintain ignition in
The system is ready to arm whenever the key is out of the ignition. Anyof the following actions will arm the alarm system:• Press the remote transmitt
SEATINGAdjustable head restraintsHead restraints help to limit head motion in the event of a rear collision.To properly adjust your head restraints, l
Lift handle to move seat forward orbackward.Pull lever up to adjust seatback.Before returning theseatback to its originalposition, make sure that carg
Comments to this Manuals